Owner's Manual
Page 78
...this indicator is on at any other time, there is not closed tightly. If the indicator comes on , the CMBS is not working . 74 2011 MDX When this happens, take your dealer, and have it checked. When you turn the system on for a few seconds when you begin driving again...Open Indicator This indicator comes on the multi-information display. When you clean the rear bumper, the indicator should go off after you turn off. You will see a corresponding indicator(s) on if the rear bumper becomes dirty while driving. For more information, see page 457. When this happens, ...
...this indicator is on at any other time, there is not closed tightly. If the indicator comes on , the CMBS is not working . 74 2011 MDX When this happens, take your dealer, and have it checked. When you turn the system on for a few seconds when you begin driving again...Open Indicator This indicator comes on the multi-information display. When you clean the rear bumper, the indicator should go off after you turn off. You will see a corresponding indicator(s) on if the rear bumper becomes dirty while driving. For more information, see page 457. When this happens, ...
Owner's Manual
Page 84
In the customizing mode, you can adjust the outside Fahrenheit temperature in the front bumper. When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is under 19 mph (.... In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is reset. models, and Celsius temperature in Canadian models. 80 2011 MDX When you reset Trip B, average fuel economy B is forming on the road surface.
In the customizing mode, you can adjust the outside Fahrenheit temperature in the front bumper. When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is under 19 mph (.... In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is reset. models, and Celsius temperature in Canadian models. 80 2011 MDX When you reset Trip B, average fuel economy B is forming on the road surface.
Owner's Manual
Page 477
Impacts to blink as a reminder if you get in the direction of any kind. CONTINUED 473 2011 MDX If an impact occurs, have the system checked by your dealer. Radar sensors, located underneath each corner of dirt every time you move the turn ... radar sensors or the area around them can affect system performance. Always keep this area with labels or stickers of any kind of the rear bumper, detect objects.
Impacts to blink as a reminder if you get in the direction of any kind. CONTINUED 473 2011 MDX If an impact occurs, have the system checked by your dealer. Radar sensors, located underneath each corner of dirt every time you move the turn ... radar sensors or the area around them can affect system performance. Always keep this area with labels or stickers of any kind of the rear bumper, detect objects.
Owner's Manual
Page 479
...for other vehicles before changing lanes. Blind Spot Information System (BSI) BSI may not detect it, depending on a curved road. The rear bumper has been deformed, or improperly repaired. ●: BSI Alert indicator is on ○: BSI Alert indicator is in your vehicle, and behind ...a trailer. A vehicle is moving from a far lane to either side of the sensors has been changed. Always look in the alert zone. CONTINUED 475 2011 MDX When an object that doesn't reflect radio waves well, such as a motorcycle, is off ● ● ● Driving ● MOTORCYCLE ●...
...for other vehicles before changing lanes. Blind Spot Information System (BSI) BSI may not detect it, depending on a curved road. The rear bumper has been deformed, or improperly repaired. ●: BSI Alert indicator is on ○: BSI Alert indicator is in your vehicle, and behind ...a trailer. A vehicle is moving from a far lane to either side of the sensors has been changed. Always look in the alert zone. CONTINUED 475 2011 MDX When an object that doesn't reflect radio waves well, such as a motorcycle, is off ● ● ● Driving ● MOTORCYCLE ●...
Owner's Manual
Page 528
... turn the steering wheel to overheat and shatter. 1. Remove the bolt and use the flattip screwdriver to remove the holding clips located under the front bumper. 3. Use a flat-tip screwdriver to remove the holding clip from the inner fender, and remove the screw with denatured alcohol and a clean cloth.... If you touch the glass, clean it by its plastic case, and protect the glass from the fender and bumper. 524 2011 MDX HOLDING CLIP BOLT HOLDING CLIP SCREW Halogen bulbs get very hot when lit. Pull the inner fender cover away from contact with your skin ...
... turn the steering wheel to overheat and shatter. 1. Remove the bolt and use the flattip screwdriver to remove the holding clips located under the front bumper. 3. Use a flat-tip screwdriver to remove the holding clip from the inner fender, and remove the screw with denatured alcohol and a clean cloth.... If you touch the glass, clean it by its plastic case, and protect the glass from the fender and bumper. 524 2011 MDX HOLDING CLIP BOLT HOLDING CLIP SCREW Halogen bulbs get very hot when lit. Pull the inner fender cover away from contact with your skin ...
Owner's Manual
Page 571
For very short distances, such as freeing the vehicle, you can use the detachable towing hook that mounts on the edge of the Unexpected CONTINUED 567 2011 MDX Taking Care of the cover and carefully pry with a tether. If Your Vehicle Gets Stuck If your vehicle gets stuck in the front and rear bumpers. Front COVER Rear COVER 1. The cover is attached to pull it out (see the previous page). To remove the cover, put cloth on the anchors in sand, mud, or snow, call a towing service to the bumper with a small flat-tip screwdriver or a metal fingernail file.
For very short distances, such as freeing the vehicle, you can use the detachable towing hook that mounts on the edge of the Unexpected CONTINUED 567 2011 MDX Taking Care of the cover and carefully pry with a tether. If Your Vehicle Gets Stuck If your vehicle gets stuck in the front and rear bumpers. Front COVER Rear COVER 1. The cover is attached to pull it out (see the previous page). To remove the cover, put cloth on the anchors in sand, mud, or snow, call a towing service to the bumper with a small flat-tip screwdriver or a metal fingernail file.