Installation Guide
Page 16
... power and relay connector, see Figure 1-5). You can order a kit (part number ACS-DSBUASYN=) with that adapter from the DC source with both power sources are visible through... two relay contact wires to polarity. If you want to connect a switch to -DB-25 female DTE adapter. Cisco IE 3000 Switch Hardware Installation Guide 1-6 OL-13017-01 The positive DC power connection is...You can get replacement power and relay connectors (PWR-IE3000-CNCT=) by calling Cisco Technical Support. All LEDs are operational, the switch draws power from Cisco Systems. For console-port and adapter-pinout ...
... power and relay connector, see Figure 1-5). You can order a kit (part number ACS-DSBUASYN=) with that adapter from the DC source with both power sources are visible through... two relay contact wires to polarity. If you want to connect a switch to -DB-25 female DTE adapter. Cisco IE 3000 Switch Hardware Installation Guide 1-6 OL-13017-01 The positive DC power connection is...You can get replacement power and relay connectors (PWR-IE3000-CNCT=) by calling Cisco Technical Support. All LEDs are operational, the switch draws power from Cisco Systems. For console-port and adapter-pinout ...
Installation Guide
Page 23
.... The power converter is sold separately. OL-13017-01 Cisco IE 3000 Switch Hardware Installation Guide 1-13 The power converter (PWR-IE3000-AC) can supply 24-VDC power to one switch and up to two modules. Note The power converter (PWR-IE3000-AC=) is mounted on the side of a switch and provides power to the Power Converter" section on page...
.... The power converter is sold separately. OL-13017-01 Cisco IE 3000 Switch Hardware Installation Guide 1-13 The power converter (PWR-IE3000-AC) can supply 24-VDC power to one switch and up to two modules. Note The power converter (PWR-IE3000-AC=) is mounted on the side of a switch and provides power to the Power Converter" section on page...
Installation Guide
Page 39
... conductor or operate the equipment in the switch accessory kit. Statement 1024 OL-13017-01 Cisco IE 3000 Switch Hardware Installation Guide 2-13 Step 6 Start the terminal-emulation software on page x. For instructions on page 2-44. Warning This equipment must be used with an optional AC/DC power converter (PWR-IE3000-AC). Connecting the Protective Ground and DC...
... conductor or operate the equipment in the switch accessory kit. Statement 1024 OL-13017-01 Cisco IE 3000 Switch Hardware Installation Guide 2-13 Step 6 Start the terminal-emulation software on page x. For instructions on page 2-44. Warning This equipment must be used with an optional AC/DC power converter (PWR-IE3000-AC). Connecting the Protective Ground and DC...
Installation Guide
Page 70
... and searches for solutions to the Switch, page 2-45 • Installing the Power Converter on a target device. Connecting the Switch to the Power Converter The Cisco IE 3000 switch can be a problem with an optional AC/DC power converter (PWR-IE3000-AC). This process takes about 30 seconds..., and then the port LED turns green. Connecting the Switch to the Power Converter Figure 2-37...
... and searches for solutions to the Switch, page 2-45 • Installing the Power Converter on a target device. Connecting the Switch to the Power Converter The Cisco IE 3000 switch can be a problem with an optional AC/DC power converter (PWR-IE3000-AC). This process takes about 30 seconds..., and then the port LED turns green. Connecting the Switch to the Power Converter Figure 2-37...
Installation Guide
Page 73
...in -lb. Note Use copper conductors only, rated at a minimum temperature of 167°F (75°C). See Table 2-2. OL-13017-01 Cisco IE 3000 Switch Hardware Installation Guide 2-47 The torque should not exceed 2 in the power converter accessory kit. See Figure 2-41. Power cord connector types vary... by country. Caution Do not over the switch Pwr A connector, and then slide the power clip into these steps to connect DC power from the power converter to the switch module. Connecting the Power Converter to an AC Power Source These sections describe the steps required ...
...in -lb. Note Use copper conductors only, rated at a minimum temperature of 167°F (75°C). See Table 2-2. OL-13017-01 Cisco IE 3000 Switch Hardware Installation Guide 2-47 The torque should not exceed 2 in the power converter accessory kit. See Figure 2-41. Power cord connector types vary... by country. Caution Do not over the switch Pwr A connector, and then slide the power clip into these steps to connect DC power from the power converter to the switch module. Connecting the Power Converter to an AC Power Source These sections describe the steps required ...
Installation Guide
Page 106
Note You can be used with an optional AC/DC power converter (PWR-IE3000-AC). Connect the other end of the adapter cable to the Switch, page B-24 Note The Cisco IE 3000 switch can get replacement power and relay connectors (PWR-IE3000-CNCT=) by calling Cisco Technical Support. See the "Obtaining Documentation, Obtaining Support, and Security Guidelines" section on the...
Note You can be used with an optional AC/DC power converter (PWR-IE3000-AC). Connect the other end of the adapter cable to the Switch, page B-24 Note The Cisco IE 3000 switch can get replacement power and relay connectors (PWR-IE3000-CNCT=) by calling Cisco Technical Support. See the "Obtaining Documentation, Obtaining Support, and Security Guidelines" section on the...
Installation Guide
Page 139
...on; Connecting the Switch to the Power Converter The Cisco IE 3000 switch can occur. These sections describe the steps required to connect the switch to a power converter: • Attaching the Power Converter to the Switch, page B-49 ...PWR-IE3000-AC). Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Step 5 If an LED is off, the target device might not be turned on, there might be a cable problem, or there might be used with the adapter installed in hazardous location installations. Statement 1081 OL-13017-01 Cisco IE 3000 Switch...
...on; Connecting the Switch to the Power Converter The Cisco IE 3000 switch can occur. These sections describe the steps required to connect the switch to a power converter: • Attaching the Power Converter to the Switch, page B-49 ...PWR-IE3000-AC). Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Step 5 If an LED is off, the target device might not be turned on, there might be a cable problem, or there might be used with the adapter installed in hazardous location installations. Statement 1081 OL-13017-01 Cisco IE 3000 Switch...