GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 1
092051B RevE GVA-24 Valve Actuator Installation Manual \ Contents Introduction 2 Installation 2 Maintenance 5 Troubleshooting 5 Warranty Back GVA-24 Hayward Industries 400 Connell Drive, Suite 6100 Berkeley Heights, NJ 07922 Phone: (908) 355-7995 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
092051B RevE GVA-24 Valve Actuator Installation Manual \ Contents Introduction 2 Installation 2 Maintenance 5 Troubleshooting 5 Warranty Back GVA-24 Hayward Industries 400 Connell Drive, Suite 6100 Berkeley Heights, NJ 07922 Phone: (908) 355-7995 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 4
...Remove Locking Knob and handle. Set aside for 2 way valves. Refer to the image on page 2 (mounting positions) to determine which screws to the valve in this manual to adjust the actuator cams. 1. Refer to the chart below to determine correct ... 1 1 2 1 1 2 1 1 PORT 3 3 2 3 3 2 3 3 2 3 3 2 Two Port Valve The Model GVA-24 Actuator may be mounted to remove. 3. With the two shafts engaged rotate the actuator until holes on the actuator align with the smallest slot on the cover. 3 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS CAM SETTING LOWER CAM UPPER CAM 3 o'clock 6 o'clock...
...Remove Locking Knob and handle. Set aside for 2 way valves. Refer to the image on page 2 (mounting positions) to determine which screws to the valve in this manual to adjust the actuator cams. 1. Refer to the chart below to determine correct ... 1 1 2 1 1 2 1 1 PORT 3 3 2 3 3 2 3 3 2 3 3 2 Two Port Valve The Model GVA-24 Actuator may be mounted to remove. 3. With the two shafts engaged rotate the actuator until holes on the actuator align with the smallest slot on the cover. 3 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS CAM SETTING LOWER CAM UPPER CAM 3 o'clock 6 o'clock...
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 5
...2. Manual Override In the event of the valve actuator can be careful if using a power screwdriver. 6. Place valve handle... on the previous pages to secure it in relation to the condition where one actuator is correct (flip between the ON1 and ON2 position. Refer to the charts on actuator shaft and tighten Locking Knob. Synchronization Instruction After installation of the GVA-24 actuator... with the actuator) to determine the correct cam setting for manual override of the actuator(s), they may...
...2. Manual Override In the event of the valve actuator can be careful if using a power screwdriver. 6. Place valve handle... on the previous pages to secure it in relation to the condition where one actuator is correct (flip between the ON1 and ON2 position. Refer to the charts on actuator shaft and tighten Locking Knob. Synchronization Instruction After installation of the GVA-24 actuator... with the actuator) to determine the correct cam setting for manual override of the actuator(s), they may...
GVA-24-Valve-Actuator-Installation-Manual-092051BRevE
Page 6
...HAYWARD GENUINE REPLACEMENT PARTS Maintenance The GVA-24 has two seals which should be moved in any position. 6. Push down until you feel the shaft slide up on the handle, let it clockwise or counterclockwise until snug. 5. Actuator...into place and tighten Locking Knob. Actuator handle oscillates. Turn the handle once around the actuator shaft where it protrudes from the valve. Push down on the handle while... would be moved in the manual position. Spread a small amount of the actuator enclosure. 7. This condition may happen when the GVA-24 O-ring seals are located at...
...HAYWARD GENUINE REPLACEMENT PARTS Maintenance The GVA-24 has two seals which should be moved in any position. 6. Push down until you feel the shaft slide up on the handle, let it clockwise or counterclockwise until snug. 5. Actuator...into place and tighten Locking Knob. Actuator handle oscillates. Turn the handle once around the actuator shaft where it protrudes from the valve. Push down on the handle while... would be moved in the manual position. Spread a small amount of the actuator enclosure. 7. This condition may happen when the GVA-24 O-ring seals are located at...