S200 Sand Filter
Page 1
... accumulated dirt in the backwash position, the water flow is automatically reversed through the sand, flushing the previously trapped dirt and debris out the waste line. IS200-98 Your Hayward S200 high-rate sand filter is a high performance, totally corrosion-proof filter that blends superior flow characteristics and features with only the least attention and care...
... accumulated dirt in the backwash position, the water flow is automatically reversed through the sand, flushing the previously trapped dirt and debris out the waste line. IS200-98 Your Hayward S200 high-rate sand filter is a high performance, totally corrosion-proof filter that blends superior flow characteristics and features with only the least attention and care...
S200 Sand Filter
Page 2
... LOSS AT MAXIMUM WORKING REQUIRED CLEARANCE DESIGN FLOW RATE PRESSURE SIDE ABOVE PSI BAR PSI BAR INCH MM INCH MM MEDIA REQUIRED TYPE AMOUNT FILTER SAND** LBS KGS S200 2.2 0.21 44 167 3.7 0.26 50 3.45 18 457 24 610 0.45-0.55 200 91 *Based on -ground pools, advises that components such ...as the filtration system, pumps and heater be positioned so as to prevent their being used as No. 20 or No. 1/2 Silica Sand. Access Dome O-Ring Filter ...
... LOSS AT MAXIMUM WORKING REQUIRED CLEARANCE DESIGN FLOW RATE PRESSURE SIDE ABOVE PSI BAR PSI BAR INCH MM INCH MM MEDIA REQUIRED TYPE AMOUNT FILTER SAND** LBS KGS S200 2.2 0.21 44 167 3.7 0.26 50 3.45 18 457 24 610 0.45-0.55 200 91 *Based on -ground pools, advises that components such ...as the filtration system, pumps and heater be positioned so as to prevent their being used as No. 20 or No. 1/2 Silica Sand. Access Dome O-Ring Filter ...
S200 Sand Filter
Page 3
...the pool water, the accumulation in the diffuser. Replace diffuser on diffuser with water to provide a cushioning effect when the filter sand is poured in the normal filter mode, filtering particles from the internal diffuser elbow pipe and place flexible automatic air relief tube to the side, out of...Carefully pour in correct amount and grade of the pool water it is good practice to backwash (clean) the filter (see BACKWASH under Filter Control Valve Functions). Remove sand shield from excessive shock. (Be sure the drain cap is securely in place and all suction and return lines ...
...the pool water, the accumulation in the diffuser. Replace diffuser on diffuser with water to provide a cushioning effect when the filter sand is poured in the normal filter mode, filtering particles from the internal diffuser elbow pipe and place flexible automatic air relief tube to the side, out of...Carefully pour in correct amount and grade of the pool water it is good practice to backwash (clean) the filter (see BACKWASH under Filter Control Valve Functions). Remove sand shield from excessive shock. (Be sure the drain cap is securely in place and all suction and return lines ...
S200 Sand Filter
Page 4
... pH levels are in intake line (indicated by unscrewing drain cap at least one complete turnover of your local authorized Hayward dealer or service center. Check surface of filter tank. partially drain & refill pool with water that has not been treated with Cyanuric Acid Rev. 12/98 ... water to set on your pool, maintain a free chlorine level of 1 to 3 ppm and a pH range of 7.2 to obtain at base of filter sand for restrictions in pool and strainer baskets for longer periods. 4. Check for algae in intake and discharge lines. 3. WINTERIZING 1. Leave cap off during winter...
... pH levels are in intake line (indicated by unscrewing drain cap at least one complete turnover of your local authorized Hayward dealer or service center. Check surface of filter tank. partially drain & refill pool with water that has not been treated with Cyanuric Acid Rev. 12/98 ... water to set on your pool, maintain a free chlorine level of 1 to 3 ppm and a pH range of 7.2 to obtain at base of filter sand for restrictions in pool and strainer baskets for longer periods. 4. Check for algae in intake and discharge lines. 3. WINTERIZING 1. Leave cap off during winter...