Installation Instructions
Page 2
... for Installation: 1. NOTE: Do not under ANSI Z21.5.1 or ANSI/UL 2158- Channel-lock adjustable pliers. 3. Rigid or flexible metal 4 inch (10.16 cm) duct. 7. The hot water temperature should be between 10 and 120 pounds per square inch (maximum unbalance pressure, hot vs. I/NFPA 54, or... 14- 30 type SRDT or ST (as restaurants or beauty salons, etc. Individual 15 amp minimum branch circuit fused with clothes dryers. Phillips head screwdriver. 2. Pipe thread sealer (Gas). 9. do not use with a time delay fuse or circuit breaker. Clear the room, building or area of your...
... for Installation: 1. NOTE: Do not under ANSI Z21.5.1 or ANSI/UL 2158- Channel-lock adjustable pliers. 3. Rigid or flexible metal 4 inch (10.16 cm) duct. 7. The hot water temperature should be between 10 and 120 pounds per square inch (maximum unbalance pressure, hot vs. I/NFPA 54, or... 14- 30 type SRDT or ST (as restaurants or beauty salons, etc. Individual 15 amp minimum branch circuit fused with clothes dryers. Phillips head screwdriver. 2. Pipe thread sealer (Gas). 9. do not use with a time delay fuse or circuit breaker. Clear the room, building or area of your...
Installation Instructions
Page 3
... installing laundry center dryer duct. 0 56 ft. (17.07 m) 42 ft. (12.8 m) 1 46 ft. (14.02 m) 36 ft. (10.97 m) 2 34 ft. (10.36 m) 28 ft. (8.53 m) 3 32 ft. (9.75 rn) 18 ft. (5.48 m) MAXIMUM LENGTH OF 4-INCH (10.2 CM) DIAMETER FLEXIBLE METAL DUCT 0 30 ft. (9.14 m) 22 ft. (6.7 m) 1 22 ft. (6.7 rn) 14 ft. (4.27 rn) 2 16 ft. (4.88 m) 10 ft. (3.05 m) 3 10 ft. (3.05 m) 5 ft. (1.5 m) The laundry...
... installing laundry center dryer duct. 0 56 ft. (17.07 m) 42 ft. (12.8 m) 1 46 ft. (14.02 m) 36 ft. (10.97 m) 2 34 ft. (10.36 m) 28 ft. (8.53 m) 3 32 ft. (9.75 rn) 18 ft. (5.48 m) MAXIMUM LENGTH OF 4-INCH (10.2 CM) DIAMETER FLEXIBLE METAL DUCT 0 30 ft. (9.14 m) 22 ft. (6.7 m) 1 22 ft. (6.7 rn) 14 ft. (4.27 rn) 2 16 ft. (4.88 m) 10 ft. (3.05 m) 3 10 ft. (3.05 m) 5 ft. (1.5 m) The laundry...
Installation Instructions
Page 4
...: 1.In an area exposed to or less than 1/2 psig (3.45 kPa). 7.The dryer MUSTbe isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 16 I (104.77 CM) 29 7116 IN ._,_ (REAR) (74.77 CM) \J ...22 CM) 411/4IN I /4 IN. (41.27 CM) 25 ¼IN. No other fuel burning appliance shall be used to connect your dryer to be outdoors. 2. CM) 30 13/16 IN. (78.26 CM) 4. A minimum of 120 square inches (774.2 square cm) of opening, Closet Door equally divided at test pressures...
...: 1.In an area exposed to or less than 1/2 psig (3.45 kPa). 7.The dryer MUSTbe isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 16 I (104.77 CM) 29 7116 IN ._,_ (REAR) (74.77 CM) \J ...22 CM) 411/4IN I /4 IN. (41.27 CM) 25 ¼IN. No other fuel burning appliance shall be used to connect your dryer to be outdoors. 2. CM) 30 13/16 IN. (78.26 CM) 4. A minimum of 120 square inches (774.2 square cm) of opening, Closet Door equally divided at test pressures...
Installation Instructions
Page 5
...is not applicable, with the termination securely fastened to the mobile home structure. 3. From the back of unit. (c) tape from dryer door. (d) foam dryer support pads. (e) inlet hoses. (f) enclosure package. 5. Using the four shipping carton corner posts (two on each side), carefully ...foam tub blocking pad. (b) foam shipping blocks from the center of the washer backsheet. ii i 4.When installing a gas dryer into a mobile home, a provision must be 4 inches (10.16 cm) in diameter with 3/8 inch (0.96 cm) socket, remove the mechanism shipping bolt and plastic spacer block from...
...is not applicable, with the termination securely fastened to the mobile home structure. 3. From the back of unit. (c) tape from dryer door. (d) foam dryer support pads. (e) inlet hoses. (f) enclosure package. 5. Using the four shipping carton corner posts (two on each side), carefully ...foam tub blocking pad. (b) foam shipping blocks from the center of the washer backsheet. ii i 4.When installing a gas dryer into a mobile home, a provision must be 4 inches (10.16 cm) in diameter with 3/8 inch (0.96 cm) socket, remove the mechanism shipping bolt and plastic spacer block from...
Installation Instructions
Page 8
Connect the exhaust duct to the dryer cabinet. NOTE: On gas dryers, before calling for future reference. REPLACEMENT PARTS If replacement parts are needed for the gas line to "OFF" and wait 5 minutes before plugging the power cord into a grounded outlet. Lift the ...with the hose pointed toward the drain. Place all other flammable vapors. Place these instructions in a location near the laundry center for service. 16. Destroy the carton, plastic bags, and metal band after servicing. Verify proper operation after the laundry center is unpacked. 8. Form a " ...
Connect the exhaust duct to the dryer cabinet. NOTE: On gas dryers, before calling for future reference. REPLACEMENT PARTS If replacement parts are needed for the gas line to "OFF" and wait 5 minutes before plugging the power cord into a grounded outlet. Lift the ...with the hose pointed toward the drain. Place all other flammable vapors. Place these instructions in a location near the laundry center for service. 16. Destroy the carton, plastic bags, and metal band after servicing. Verify proper operation after the laundry center is unpacked. 8. Form a " ...