Operating Instructions 2
Page 15
... be performed with these angle grinders, identified by flanges, the arbour hole of water. Anyone entering the work area. WEV 15-125 Quick HT, WEV 15-125 Quick Inox can also be observed. 3. The user bears sole responsibility for grinding, sanding, abrasive cutting-off tool. WARNING - ...tool. Specified Use The angle grinders, when fitted with this test time. Machines with the designation WEV are marked with original Metabo accessories, are not specifically designed and recommended by various operations. General Safety Instructions For your own protection and for *4) - ...
... be performed with these angle grinders, identified by flanges, the arbour hole of water. Anyone entering the work area. WEV 15-125 Quick HT, WEV 15-125 Quick Inox can also be observed. 3. The user bears sole responsibility for grinding, sanding, abrasive cutting-off tool. WARNING - ...tool. Specified Use The angle grinders, when fitted with this test time. Machines with the designation WEV are marked with original Metabo accessories, are not specifically designed and recommended by various operations. General Safety Instructions For your own protection and for *4) - ...
Operating Instructions 2
Page 17
... the use cutting discs for your body. ENGLISH en Grinding discs must be replaced. Damaged, eccentric or vibrating tools must be used. Metabo S-automatic safety clutch. The risk depends on the spindle length and thread. Do the following to reduce exposure to these substances include:...that the thread in the accessory must be allowed to eliminate the cause of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for wood treatment (chromate, wood preservatives), some wood types (such as respirators able to spin ...
... the use cutting discs for your body. ENGLISH en Grinding discs must be replaced. Damaged, eccentric or vibrating tools must be used. Metabo S-automatic safety clutch. The risk depends on the spindle length and thread. Do the following to reduce exposure to these substances include:...that the thread in the accessory must be allowed to eliminate the cause of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for wood treatment (chromate, wood preservatives), some wood types (such as respirators able to spin ...
Operating Instructions 2
Page 18
... the lever engages. - Reduce dust exposure with vibration damping * 12 Safety cover 13 2-hole nut * 14 2-hole spanner * 15 Lever for selection of delivery 6. See illustration C on the rating label, match with "Metabo Quick System". Make sure that the 2 lugs engage in the position indicated. (12) - Fit the support flange on the spindle...
... the lever engages. - Reduce dust exposure with vibration damping * 12 Safety cover 13 2-hole nut * 14 2-hole spanner * 15 Lever for selection of delivery 6. See illustration C on the rating label, match with "Metabo Quick System". Make sure that the 2 lugs engage in the position indicated. (12) - Fit the support flange on the spindle...
Operating Instructions 2
Page 19
...from the mains socket or if there has been a power cut out of 30° - 40° for W 9-100: The collar of the lever (15). Switch on page 2. Therefore, always hold the machine with its sheet metal part) and put aside. - Unscrew the 4 gear housing screws (b). Do not...chips. X) For thin grinding discs: The edge of the 2-hole nut are different. Locking the spindle. Turn the 2-hole nut (13)clockwise using the red M-Quick spindle locking button! (4) - Machines with paddle switch (with dead man function): 89 0 I 7.4 Securing/Releasing the 2-hole nut (depending on the surface and ...
...from the mains socket or if there has been a power cut out of 30° - 40° for W 9-100: The collar of the lever (15). Switch on page 2. Therefore, always hold the machine with its sheet metal part) and put aside. - Unscrew the 4 gear housing screws (b). Do not...chips. X) For thin grinding discs: The edge of the 2-hole nut are different. Locking the spindle. Turn the 2-hole nut (13)clockwise using the red M-Quick spindle locking button! (4) - Machines with paddle switch (with dead man function): 89 0 I 7.4 Securing/Releasing the 2-hole nut (depending on the surface and ...
Operating Instructions 2
Page 20
...using a suitable extraction unit. Repairs Repairs to the side and re-insert the lever (15) (with its sheet metal part), and fix with VTC and TC electronics: The electronic ... the clamping shank on model) flashes. Changes due to this operation, separate the power tool from www.metabo.com. 13. permitted thickness of accessory M = spindle thread l = length of the accessory tmax,1...shank on again. 11. B Extraction guard for cutting through all front and rear air vents using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. Tightening torque = 5.0 Nm +/-...
...using a suitable extraction unit. Repairs Repairs to the side and re-insert the lever (15) (with its sheet metal part), and fix with VTC and TC electronics: The electronic ... the clamping shank on model) flashes. Changes due to this operation, separate the power tool from www.metabo.com. 13. permitted thickness of accessory M = spindle thread l = length of the accessory tmax,1...shank on again. 11. B Extraction guard for cutting through all front and rear air vents using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. Tightening torque = 5.0 Nm +/-...