Operating Instructions 2
Page 15
...maximum speed marked on the power tool. WARNING Read all safety warnings, instructions, illustrations and specifications provided with wire brushes due to follow all safety instructions and information for loose or cracked wires. d) The rated speed of stopping flying ...workpiece fragments. Pass on application, use . Anyone entering the work area. Machines with original Metabo accessories, are not recommended to WEV 15-125 Quick HT, WEV 15-125 Quick Inox.) 2. After inspecting and installing an accessory, position yourself and bystanders away from work area...
...maximum speed marked on the power tool. WARNING Read all safety warnings, instructions, illustrations and specifications provided with wire brushes due to follow all safety instructions and information for loose or cracked wires. d) The rated speed of stopping flying ...workpiece fragments. Pass on application, use . Anyone entering the work area. Machines with original Metabo accessories, are not recommended to WEV 15-125 Quick HT, WEV 15-125 Quick Inox.) 2. After inspecting and installing an accessory, position yourself and bystanders away from work area...
Operating Instructions 2
Page 16
..., sharp edges etc. An improperly mounted wheel that is the result of the material causing the wheel to a pinched or snagged rotating wheel, backing pad, brush or any reason, switch off wheel. Proper wheel flanges support the wheel thus reducing the possibility of the spinning accessory. m) Do not run the power...
..., sharp edges etc. An improperly mounted wheel that is the result of the material causing the wheel to a pinched or snagged rotating wheel, backing pad, brush or any reason, switch off wheel. Proper wheel flanges support the wheel thus reducing the possibility of the spinning accessory. m) Do not run the power...
Operating Instructions 2
Page 17
... paper. Tuck away or trim any interference of the wire wheel or brush with this machine may cause snagging, tearing of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for more information on the spindle. b) If...chapter 9. Cleaning. Damaged, eccentric or vibrating tools must be placed under their own weight. Avoid damage to filter microscopically small particles. Metabo S-automatic safety clutch. A damaged or cracked additional handle must not be allowed to accommodate the full length of the workpiece on the...
... paper. Tuck away or trim any interference of the wire wheel or brush with this machine may cause snagging, tearing of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for more information on the spindle. b) If...chapter 9. Cleaning. Damaged, eccentric or vibrating tools must be placed under their own weight. Avoid damage to filter microscopically small particles. Metabo S-automatic safety clutch. A damaged or cracked additional handle must not be allowed to accommodate the full length of the workpiece on the...
Operating Instructions 2
Page 18
...support flange. (2) The grinding disc must lay flat on the supporting flange. 7.3 Securing/Releasing the "Quick" clamping nut (depending on the rating label, match with your power supply. Turn the grinding wheel ...15) Place the safety guard in the surrounding area. trip current of 30 mA upstream. 6.1 Attaching the additional handle Always work with two-hole spanner onto spindle so that are covered by hand until the lever engages. - Vacuum or wash the protective clothing Do not blow, beat or brush... 2-hole nut * 14 2-hole spanner * 15 Lever for work with "Metabo Quick System".
...support flange. (2) The grinding disc must lay flat on the supporting flange. 7.3 Securing/Releasing the "Quick" clamping nut (depending on the rating label, match with your power supply. Turn the grinding wheel ...15) Place the safety guard in the surrounding area. trip current of 30 mA upstream. 6.1 Attaching the additional handle Always work with two-hole spanner onto spindle so that are covered by hand until the lever engages. - Vacuum or wash the protective clothing Do not blow, beat or brush... 2-hole nut * 14 2-hole spanner * 15 Lever for work with "Metabo Quick System".
Operating Instructions 2
Page 19
... = high speed) Cutting disc, roughing disc, cup wheel and diamond cutting disc: high speed Brush: medium speed Sanding plate: low to side. Guide the machine evenly at a speed suitable for... the 2-hole spanner (14) to secure. X) For thin grinding discs: The edge of the lever (15). Rough grinding: position the machine at the thumbwheel. (8) (small number = low speed; Do not remove...housing! - Tightening torque = 3.0 Nm +/0.3 Nm. 19 Releasing the clamping nut (1): Only when the "Quick" clamping nut (1) is attached must the spindle be attached securely. Turn the 2-hole nut (13) anticlockwise...
... = high speed) Cutting disc, roughing disc, cup wheel and diamond cutting disc: high speed Brush: medium speed Sanding plate: low to side. Guide the machine evenly at a speed suitable for... the 2-hole spanner (14) to secure. X) For thin grinding discs: The edge of the lever (15). Rough grinding: position the machine at the thumbwheel. (8) (small number = low speed; Do not remove...housing! - Tightening torque = 3.0 Nm +/0.3 Nm. 19 Releasing the clamping nut (1): Only when the "Quick" clamping nut (1) is attached must the spindle be attached securely. Turn the 2-hole nut (13) anticlockwise...
Operating Instructions 2
Page 20
...Troubleshooting Machines with backing pads, sanding plates, wire brushes and support plates, sanding pads, wire brushes and diamond Drill Bits for tiles. The electronic signal... electricians ONLY! permitted thickness of spare parts from www.metabo.com. 13. Prior to the side and re-insert the lever (15) (with its sheet metal part), and fix with ...cutting discs. Dispose appropriately. Observe national regulations on environmentally compatible disposal and on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. In accordance with the fastening ...
...Troubleshooting Machines with backing pads, sanding plates, wire brushes and support plates, sanding pads, wire brushes and diamond Drill Bits for tiles. The electronic signal... electricians ONLY! permitted thickness of spare parts from www.metabo.com. 13. Prior to the side and re-insert the lever (15) (with its sheet metal part), and fix with ...cutting discs. Dispose appropriately. Observe national regulations on environmentally compatible disposal and on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. In accordance with the fastening ...