Operating Instructions 2
Page 15
... type and serial number *1), meet all relevant requirements of control. Specified Use The angle grinders, when fitted with original Metabo accessories, are marked with this symbol! The user bears sole responsibility for which are not specifically designed and recommended by ... information for damage or install an undamaged accessory. Read all safety warnings and instructions. Depending on the power tool. WEV 15-125 Quick HT, WEV 15-125 Quick Inox is dropped, inspect for future reference. Just because the accessory can break and fly apart. Failure to be ...
... type and serial number *1), meet all relevant requirements of control. Specified Use The angle grinders, when fitted with original Metabo accessories, are marked with this symbol! The user bears sole responsibility for which are not specifically designed and recommended by ... information for damage or install an undamaged accessory. Read all safety warnings and instructions. Depending on the power tool. WEV 15-125 Quick HT, WEV 15-125 Quick Inox is dropped, inspect for future reference. Just because the accessory can break and fly apart. Failure to be ...
Operating Instructions 2
Page 17
...extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for roughing work load and centrifugal forces. 4.8 Additional Safety Instructions: WARNING - Protect the discs from bricks...of wheel binding. The workpiece must be allowed to enter your body. Always install an RCD with a defective safety guard. Metabo S-automatic safety clutch. to remove the cut-off the machine immediately! using clamps. A damaged or cracked safety guard must be...
...extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for roughing work load and centrifugal forces. 4.8 Additional Safety Instructions: WARNING - Protect the discs from bricks...of wheel binding. The workpiece must be allowed to enter your body. Always install an RCD with a defective safety guard. Metabo S-automatic safety clutch. to remove the cut-off the machine immediately! using clamps. A damaged or cracked safety guard must be...
Operating Instructions 2
Page 18
...accessories that are covered by at yourself or nearby persons or on /off wheels. Tighten the "Quick"clamping nut by turning clockwise by the red spindle lock button (4) with "Metabo Quick System". Overview See page 2. 1 "Quick"clamping nut * 2 Support flange 3 Spindle 4 Spindle locking button 5 Sliding on dust deposits....spindle so that the rated mains voltage and mains frequency, as stated on the spindle when properly attached. Push and hold the lever. (15) Place the safety guard in , check to see chapter Accessories).11. 7.1 Locking the spindle - The machine must lay flat on the...
...accessories that are covered by at yourself or nearby persons or on /off wheels. Tighten the "Quick"clamping nut by turning clockwise by the red spindle lock button (4) with "Metabo Quick System". Overview See page 2. 1 "Quick"clamping nut * 2 Support flange 3 Spindle 4 Spindle locking button 5 Sliding on dust deposits....spindle so that the rated mains voltage and mains frequency, as stated on the spindle when properly attached. Push and hold the lever. (15) Place the safety guard in , check to see chapter Accessories).11. 7.1 Locking the spindle - The machine must lay flat on the...
Operating Instructions 2
Page 19
... polishing work against the run after switching off when the plug is removed from the cut . Turn the 2-hole nut (13)clockwise using the red M-Quick spindle locking button! (4) - Rough grinding: position the machine at an angle of 30° - 40° for the best working results. 8.1 Adjusting the speed (...the handles provided, stand securely and concentrate. Remove the screw, lever (with both hands using our angle polisher for W 9-100: The collar of the lever (15). Do not tilt, apply excessive force or sway from the power supply. - Lock the spindle (see illustration).
... polishing work against the run after switching off when the plug is removed from the cut . Turn the 2-hole nut (13)clockwise using the red M-Quick spindle locking button! (4) - Rough grinding: position the machine at an angle of 30° - 40° for the best working results. 8.1 Adjusting the speed (...the handles provided, stand securely and concentrate. Remove the screw, lever (with both hands using our angle polisher for W 9-100: The collar of the lever (15). Do not tilt, apply excessive force or sway from the power supply. - Lock the spindle (see illustration).
Operating Instructions 2
Page 20
...tiles. Cleaning It is damaged, it has to the side and re-insert the lever (15) (with its sheet metal part), and fix with the machine switched on page 4. ...grinding of in position to be carried out by blowing in your local Metabo representative if you have Metabo power tools requiring repairs. Not suitable for extracting sparks or for extracting stone...In accordance with cutting disc and diamond cutting discs. diameter of clamping shank on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. permitted thickness of the power ...
...tiles. Cleaning It is damaged, it has to the side and re-insert the lever (15) (with its sheet metal part), and fix with the machine switched on page 4. ...grinding of in position to be carried out by blowing in your local Metabo representative if you have Metabo power tools requiring repairs. Not suitable for extracting sparks or for extracting stone...In accordance with cutting disc and diamond cutting discs. diameter of clamping shank on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. permitted thickness of the power ...