TTV678 Owners Manual (Internal Charger)
Page 22
... been idle for loose wires and loose screws. * Cycle key switch to resume normal operation. * Replace controller. * Refer to water ingress. Number of a connection block - Vario functions disabled cycle key switch! If Fault Persists. * 4 Bars Flash once with pause. * 4 Bars Flash twice with pause. * System trip. * Spare Solenoid connection trip. * System...
... been idle for loose wires and loose screws. * Cycle key switch to resume normal operation. * Replace controller. * Refer to water ingress. Number of a connection block - Vario functions disabled cycle key switch! If Fault Persists. * 4 Bars Flash once with pause. * 4 Bars Flash twice with pause. * System trip. * Spare Solenoid connection trip. * System...
TTV678 Owners Manual (Internal Charger)
Page 23
... not activated without seat switch being activated (nobody on seat) Or seat switch momentarily deactivated while accelerator pedal being activated during switch on of Vario. * Cycle Key switch to resume normal operation . * Check controller and harness wiring with special attention to wires p2/03 and p2/10... 1 to 10 and 10 back to 1) and repeats. * Bars cycle from 1 to 10 continuously and repeats. * Accelerator pedal movement detected during Vario start up sequence (partially pressed or jammed). * Machine inhibit. * Foot or object on pedal during switch on or possible jamming of pedal. * ...
... not activated without seat switch being activated (nobody on seat) Or seat switch momentarily deactivated while accelerator pedal being activated during switch on of Vario. * Cycle Key switch to resume normal operation . * Check controller and harness wiring with special attention to wires p2/03 and p2/10... 1 to 10 and 10 back to 1) and repeats. * Bars cycle from 1 to 10 continuously and repeats. * Accelerator pedal movement detected during Vario start up sequence (partially pressed or jammed). * Machine inhibit. * Foot or object on pedal during switch on or possible jamming of pedal. * ...
TTV678 Owners Manual (External Charger)
Page 21
... of bars flashing on display Fault Possible Cause Effect on incline. " Cycle Key switch to resume normal operation. * If the above fails then: * Switch off . Vario functions disabled cycle key switch! Number of a connection block - blocked exhaust. * Vac motor will not operate. * 5 Bars flash continuously. * Vac Motor is disconnected, has failed...
... of bars flashing on display Fault Possible Cause Effect on incline. " Cycle Key switch to resume normal operation. * If the above fails then: * Switch off . Vario functions disabled cycle key switch! Number of a connection block - blocked exhaust. * Vac motor will not operate. * 5 Bars flash continuously. * Vac Motor is disconnected, has failed...
TTV678 Owners Manual (External Charger)
Page 22
... to 10 and 10 back to 1) and repeats. * Bars cycle from 1 to 10 continuously and repeats. * Accelerator pedal movement detected during Vario start up sequence (partially pressed or jammed). * Machine inhibit. * Foot or object on pedal during switch on or possible jamming of pedal. *...Number of bars flashing on display Fault Possible Cause * 6 Bars flash continuously. * Control system is not jammed or depressed during switch on of Vario. * Cycle Key switch to resume normal operation . * Check controller and harness wiring with pause. * Accelerator pedal trip. Investigate the Following ...
... to 10 and 10 back to 1) and repeats. * Bars cycle from 1 to 10 continuously and repeats. * Accelerator pedal movement detected during Vario start up sequence (partially pressed or jammed). * Machine inhibit. * Foot or object on pedal during switch on or possible jamming of pedal. *...Number of bars flashing on display Fault Possible Cause * 6 Bars flash continuously. * Control system is not jammed or depressed during switch on of Vario. * Cycle Key switch to resume normal operation . * Check controller and harness wiring with pause. * Accelerator pedal trip. Investigate the Following ...