Owner Manual
Page 9
... B terminals Connect Speakers B. Q POWER CORD (A-9030 only) See "Connections" for connection information (➔ page 12). I PRE OUT L/R jacks (A-9050 only) Connect a power amplifier when the integrated amplifier is used as CD players with analog audio output. P AC INLET...function. E DIGITAL IN COAXIAL D1/D2 jacks (A-9050 only) Connect components such as a preamplifier (Pre mode). J PREOUT SUBWOOFER jack K V REMOTE CONTROL jack Connect Onkyo components such as Onkyo Docks, CD Players, or Tuner with analog audio output. F PHONO (MM) L/R jacks Connect a turntable with coaxial...
... B terminals Connect Speakers B. Q POWER CORD (A-9030 only) See "Connections" for connection information (➔ page 12). I PRE OUT L/R jacks (A-9050 only) Connect a power amplifier when the integrated amplifier is used as CD players with analog audio output. P AC INLET...function. E DIGITAL IN COAXIAL D1/D2 jacks (A-9050 only) Connect components such as a preamplifier (Pre mode). J PREOUT SUBWOOFER jack K V REMOTE CONTROL jack Connect Onkyo components such as Onkyo Docks, CD Players, or Tuner with analog audio output. F PHONO (MM) L/R jacks Connect a turntable with coaxial...
Owner Manual
Page 19
...from LINE OUT. • See the manual of the following jacks: LINE IN 1/2/3/4. In this case, connect the turntable to the phono preamp's input, and connect the phono preamp's output to GND terminal. Integrated Amplifier Connecting a Cassette Tape Deck Integrated Amplifier L R AUDIO IN Cassette tape deck Cassette tape...tape deck to either of the recording component for use with moving-magnet (MM) type cartridges. Use an analog audio cable to connect the PHONO L/R jacks to be disconnected. • If the turntable has a moving-coil (MC) type cartridge, you have the full consent of ...
...from LINE OUT. • See the manual of the following jacks: LINE IN 1/2/3/4. In this case, connect the turntable to the phono preamp's input, and connect the phono preamp's output to GND terminal. Integrated Amplifier Connecting a Cassette Tape Deck Integrated Amplifier L R AUDIO IN Cassette tape deck Cassette tape...tape deck to either of the recording component for use with moving-magnet (MM) type cartridges. Use an analog audio cable to connect the PHONO L/R jacks to be disconnected. • If the turntable has a moving-coil (MC) type cartridge, you have the full consent of ...
Owner Manual
Page 23
...-range clarity-allowing vocals and strings to the selected input will blink when D1, D2 or D3 is selected and a signal is not input. (A-9050 only) ■ Operating with the remote controller Using the Direct Function By bypassing the tone control circuit, the Direct function uses the shortest path for... LED PHASE MATCHING BASS button 1 Press the PHASE MATCHING BASS button. En 23 Choose an input from the following: LINE1, LINE2, LINE3, LINE4, LINE5, PHONO (D1, D2, D3 (A-9050 only)) The LED corresponding to shine-while maintaining a smooth, powerful bass response at all volume levels.
...-range clarity-allowing vocals and strings to the selected input will blink when D1, D2 or D3 is selected and a signal is not input. (A-9050 only) ■ Operating with the remote controller Using the Direct Function By bypassing the tone control circuit, the Direct function uses the shortest path for... LED PHASE MATCHING BASS button 1 Press the PHASE MATCHING BASS button. En 23 Choose an input from the following: LINE1, LINE2, LINE3, LINE4, LINE5, PHONO (D1, D2, D3 (A-9050 only)) The LED corresponding to shine-while maintaining a smooth, powerful bass response at all volume levels.
Owner Manual
Page 27
...Otherwise, it to lockup. Please refer to the V connection section in phono preamp, connect a turntable to PHONO (➔ page 19). • Make sure that the ground wire is set correctly (➔ page 17). Onkyo is connected correctly (➔ page 14). Check that each device is ... Remote Controller The remote controller doesn't work properly. • Make sure the batteries have a built-in the owner's manual of the Onkyo Dock connected via V is connected to the integrated amplifier correctly. In the unlikely event that the V cable is automatically turned off (➔...
...Otherwise, it to lockup. Please refer to the V connection section in phono preamp, connect a turntable to PHONO (➔ page 19). • Make sure that the ground wire is set correctly (➔ page 17). Onkyo is connected correctly (➔ page 14). Check that each device is ... Remote Controller The remote controller doesn't work properly. • Make sure the batteries have a built-in the owner's manual of the Onkyo Dock connected via V is connected to the integrated amplifier correctly. In the unlikely event that the V cable is automatically turned off (➔...
Owner Manual
Page 28
En 28 Specifications A-9050 A-9030 Rated Output Power (North American) (IEC) 2 ch × 65 W at 8 ohms, 1 kHz, 2 ch Driven of (FTC) 75 watts minimum continuous power per 0.08 % channel, 8 ... 8.2 kg (18.1 lbs) 7.4 kg (16.3 lbs) ■ Audio Inputs Digital Inputs Analog Stereo Inputs 1 (Rear Optical) 2 (Rear Coaxial) LINE1, LINE2, LINE3, LINE4, LINE5, PHONO LINE1, LINE2, LINE3, LINE4, LINE5, PHONO ■ Audio Outputs Analog Stereo Outputs Subwoofer Pre Outputs Speaker Outputs Phones LINE OUT, PRE OUT 1 SP-A, B 1 (6.3 ø) LINE OUT 1 SP-A, B 1 (6.3 ø...
En 28 Specifications A-9050 A-9030 Rated Output Power (North American) (IEC) 2 ch × 65 W at 8 ohms, 1 kHz, 2 ch Driven of (FTC) 75 watts minimum continuous power per 0.08 % channel, 8 ... 8.2 kg (18.1 lbs) 7.4 kg (16.3 lbs) ■ Audio Inputs Digital Inputs Analog Stereo Inputs 1 (Rear Optical) 2 (Rear Coaxial) LINE1, LINE2, LINE3, LINE4, LINE5, PHONO LINE1, LINE2, LINE3, LINE4, LINE5, PHONO ■ Audio Outputs Analog Stereo Outputs Subwoofer Pre Outputs Speaker Outputs Phones LINE OUT, PRE OUT 1 SP-A, B 1 (6.3 ø) LINE OUT 1 SP-A, B 1 (6.3 ø...