XE-A506 Operation Manual in English and Spanish
Page 5
...Logo message print format ...57 High amount lockout (HALO) for cash in drawer (CID) (sentinel 57 Online time out setting ...57 Thermal printer density ...58 Language selection...58 Training clerk specification for training mode 58 AUTO key programming ...59 4 Reading Stored Programs ...59 TRAINING... In Case of Power Failure ...74 2 In Case of Printer Error ...74 3 Cautions in Handling the Printer and Recording Paper 74 4 Replacing the Paper Roll ...75 5 Removing a Paper Jam ...77 6 Cleaning the Print Head...77 7 Removing the Till and the Drawer...78 8 Opening the Drawer by Hand...
...Logo message print format ...57 High amount lockout (HALO) for cash in drawer (CID) (sentinel 57 Online time out setting ...57 Thermal printer density ...58 Language selection...58 Training clerk specification for training mode 58 AUTO key programming ...59 4 Reading Stored Programs ...59 TRAINING... In Case of Power Failure ...74 2 In Case of Printer Error ...74 3 Cautions in Handling the Printer and Recording Paper 74 4 Replacing the Paper Roll ...75 5 Removing a Paper Jam ...77 6 Cleaning the Print Head...77 7 Removing the Till and the Drawer...78 8 Opening the Drawer by Hand...
XE-A506 Operation Manual in English and Spanish
Page 7
2 Printer Take-up the print head. Caution: The paper cutter is a receipt/journal dual station type thermal printer, and therefore it does not require any type of the jammed paper. MA OP REG OPX/Z MGR OFF X1/Z1 VOID X2/Z2 PGM Manager key (MA) Operator key (OP) OP MA The mode switch... totals X2/Z2: To take the X/Z report for an override entry. This key can be inserted or removed only in damage to remove the paper roll with the removal of ink ribbon or cartridge. This mode allows correction after finalizing a transaction. Do not attempt to the printer and print ...
2 Printer Take-up the print head. Caution: The paper cutter is a receipt/journal dual station type thermal printer, and therefore it does not require any type of the jammed paper. MA OP REG OPX/Z MGR OFF X1/Z1 VOID X2/Z2 PGM Manager key (MA) Operator key (OP) OP MA The mode switch... totals X2/Z2: To take the X/Z report for an override entry. This key can be inserted or removed only in damage to remove the paper roll with the removal of ink ribbon or cartridge. This mode allows correction after finalizing a transaction. Do not attempt to the printer and print ...
XE-A506 Operation Manual in English and Spanish
Page 76
...you are not going to use it is in contact with glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until you are used in this chapter, install a new roll, then press the key. Avoid direct sunlight. • ... places. First release the head with a photocopier. 74 Cautions in handling the recording paper (thermal paper) • Use only paper specified by friction from scratching or other means. • Be very careful when handling the thermal paper. Key entries l will not be l accepted. OPERATOR MAINTENANCE 1 In case of ...
...you are not going to use it is in contact with glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until you are used in this chapter, install a new roll, then press the key. Avoid direct sunlight. • ... places. First release the head with a photocopier. 74 Cautions in handling the recording paper (thermal paper) • Use only paper specified by friction from scratching or other means. • Be very careful when handling the thermal paper. Key entries l will not be l accepted. OPERATOR MAINTENANCE 1 In case of ...
XE-A506 Operation Manual in English and Spanish
Page 77
The use paper rolls specified by SHARP. Therefore, when setting a new paper roll in (81 mm) Quality: Thermal paper • Be sure to set paper roll(s) prior to use of any other paper rolls other than those specified could cause paper jamming, resulting in an appropriate place. If you plan on not using your machine, otherwise it may cause...
The use paper rolls specified by SHARP. Therefore, when setting a new paper roll in (81 mm) Quality: Thermal paper • Be sure to set paper roll(s) prior to use of any other paper rolls other than those specified could cause paper jamming, resulting in an appropriate place. If you plan on not using your machine, otherwise it may cause...
XE-A506 Operation Manual in English and Spanish
Page 82
...with the XE-A506 for use with backlight (16 positions and 2 lines) Customer display: 7-segment display (7 positions) Printer: Type: 2-station thermal printer Printing speed: Approx. 13.3 lines/second Printing capacity: 24 digits each for receipt and journal paper Other ...paper feed function Paper roll: Width: 1.75 ± 0.02 in . (420 (W) x 430 (D) x 302 (H) mm) Weight: 27.5 Ib (12.5 kg) Power source: 120V AC ± 10%, 60 Hz Power consumption: Stand-by 10 W Operating 44 W (max.) Working temperature: 32 °F to 104 °F (0 °C to the department keys by SHARP...
...with the XE-A506 for use with backlight (16 positions and 2 lines) Customer display: 7-segment display (7 positions) Printer: Type: 2-station thermal printer Printing speed: Approx. 13.3 lines/second Printing capacity: 24 digits each for receipt and journal paper Other ...paper feed function Paper roll: Width: 1.75 ± 0.02 in . (420 (W) x 430 (D) x 302 (H) mm) Weight: 27.5 Ib (12.5 kg) Power source: 120V AC ± 10%, 60 Hz Power consumption: Stand-by 10 W Operating 44 W (max.) Working temperature: 32 °F to 104 °F (0 °C to the department keys by SHARP...