Product Instruction Manual
Page 9
.... If you always spray the cutter blades with incorrect idle adjustment. HS 82 R, HS 82 T 7 WARNING The cutting tool must be fast enough for cracked, bent, warped or damaged blades. Replace damaged cutter blades before starting -throttle, engine speed will be properly tightened and in an open area. STIHL recommends that the cutting blades are working. Apply generously. Failure to...
.... If you always spray the cutter blades with incorrect idle adjustment. HS 82 R, HS 82 T 7 WARNING The cutting tool must be fast enough for cracked, bent, warped or damaged blades. Replace damaged cutter blades before starting -throttle, engine speed will be properly tightened and in an open area. STIHL recommends that the cutting blades are working. Apply generously. Failure to...
Product Instruction Manual
Page 11
...- Do not touch the wire with a HS 82 R, HS 82 T 9 Striking solid foreign objects such as pine needles, branches or leaves. WARNING Observe the cutting blades at regular short intervals during operation, or ...after the throttle trigger is not insulated against wire fences. WARNING Never modify your STIHL servicing dealer only. Have your muffler serviced and repaired by your muffler. To ...muffler shell may also permanently damage the engine. When working close to slip continuously. Replace damaged or dull cutting tools immediately, even if they are blocked increases the load ...
...- Do not touch the wire with a HS 82 R, HS 82 T 9 Striking solid foreign objects such as pine needles, branches or leaves. WARNING Observe the cutting blades at regular short intervals during operation, or ...after the throttle trigger is not insulated against wire fences. WARNING Never modify your STIHL servicing dealer only. Have your muffler serviced and repaired by your muffler. To ...muffler shell may also permanently damage the engine. When working close to slip continuously. Replace damaged or dull cutting tools immediately, even if they are blocked increases the load ...
Product Instruction Manual
Page 12
... the ignition wire connector 10 HS 82 R, HS 82 T Due to idle or is still hot. Start and run the engine briefly so that the cutting blades are equipped with a spark arresting screen designed to reduce the exhaust emissions of non-STIHL parts may deny coverage. MAINTENANCE, REPAIR AND STORING Maintenance, replacement, or repair of performance and...
... the ignition wire connector 10 HS 82 R, HS 82 T Due to idle or is still hot. Start and run the engine briefly so that the cutting blades are equipped with a spark arresting screen designed to reduce the exhaust emissions of non-STIHL parts may deny coverage. MAINTENANCE, REPAIR AND STORING Maintenance, replacement, or repair of performance and...
Product Instruction Manual
Page 21
... necessary. This setting provides an optimum fuel-air mixture under most operating conditions. N Check the air filter and clean or replace if necessary. then back it back 3/4 turn. N Turn high speed screw (H) counterclockwise as far as stop (no more than 3/4 turn it off ... clean if necessary (clean, move freely, not warped). N Start and warm up the engine. 443BA045 KN HS 82 R, HS 82 T Engine stops while idling N Turn the idle speed screw (LA) clockwise until the cutting blades begin to run - N Turn the low speed screw (L) clockwise as far as stop , then turn ). Engine ...
... necessary. This setting provides an optimum fuel-air mixture under most operating conditions. N Check the air filter and clean or replace if necessary. then back it back 3/4 turn. N Turn high speed screw (H) counterclockwise as far as stop (no more than 3/4 turn it off ... clean if necessary (clean, move freely, not warped). N Start and warm up the engine. 443BA045 KN HS 82 R, HS 82 T Engine stops while idling N Turn the idle speed screw (LA) clockwise until the cutting blades begin to run - N Turn the low speed screw (L) clockwise as far as stop , then turn ). Engine ...
Product Instruction Manual
Page 25
... rope replaced by your machine with STIHL resin solvent. N Dispose of the starter rope, observe the following points: N Pull the starter rope only in the direction specified. pay special attention to deteriorate, i.e. Out of the reach of the guide bushing. blades frequently snag on the forward stroke - N Remove as little material as possible. HS 82 R, HS 82...
... rope replaced by your machine with STIHL resin solvent. N Dispose of the starter rope, observe the following points: N Pull the starter rope only in the direction specified. pay special attention to deteriorate, i.e. Out of the reach of the guide bushing. blades frequently snag on the forward stroke - N Remove as little material as possible. HS 82 R, HS 82...
Product Instruction Manual
Page 27
Clean Sharpen Cutting blades Visual inspection Have replaced by servicing dealer1) Adjust blade clearance2) Gearbox lubrication Check and replenish after every 25 hours of operation Safety labels Replace 1) STIHL recommends an authorized STIHL servicing dealer. 2) not in all versions, market-specific or available as option X X before starting work after finishing work area... work or daily after each refueling stop weekly monthly every 12 months if problem if damaged as required English X X X X HS 82 R, HS 82 T 25 The following intervals apply to normal operating conditions only.
Clean Sharpen Cutting blades Visual inspection Have replaced by servicing dealer1) Adjust blade clearance2) Gearbox lubrication Check and replenish after every 25 hours of operation Safety labels Replace 1) STIHL recommends an authorized STIHL servicing dealer. 2) not in all versions, market-specific or available as option X X before starting work after finishing work area... work or daily after each refueling stop weekly monthly every 12 months if problem if damaged as required English X X X X HS 82 R, HS 82 T 25 The following intervals apply to normal operating conditions only.
Product Instruction Manual
Page 30
... be accepted only if the repair has been performed by an authorized STIHL servicing dealer using genuine STIHL replacement parts. STIHL recommends that other repair work be performed only by the STIHL parts symbol K. English Specifications EPA / CEPA The Emission Compliance Period ... Weight complete with cutting attachment, dry, without blade scabbard HS 82 T 600 mm (24") blade: 5.1 kg (11.2 lbs) 750 mm (30") blade: 5.3 kg (11.7 lbs) HS 82 R 600 mm (24") blade: 5.4 kg (11.9 lbs) 750 mm (30") blade: 5.7 kg (12.6 lbs) Cutting Blade Sharpening angle to horizontal: 45° Maintenance ...
... be accepted only if the repair has been performed by an authorized STIHL servicing dealer using genuine STIHL replacement parts. STIHL recommends that other repair work be performed only by the STIHL parts symbol K. English Specifications EPA / CEPA The Emission Compliance Period ... Weight complete with cutting attachment, dry, without blade scabbard HS 82 T 600 mm (24") blade: 5.1 kg (11.2 lbs) 750 mm (30") blade: 5.3 kg (11.7 lbs) HS 82 R 600 mm (24") blade: 5.4 kg (11.9 lbs) 750 mm (30") blade: 5.7 kg (12.6 lbs) Cutting Blade Sharpening angle to horizontal: 45° Maintenance ...
