Installation Guide
Page 2
...of your washer. If you have: Overhead sewer 1" (25 mm) standpipe Drain hose too short Lint clogged drain Floor drain system You will need: Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers) 2" (51 mm) diameter to... 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835 Extension Drain Hose Part Number 285863 Connector Kit Part Number ...
...of your washer. If you have: Overhead sewer 1" (25 mm) standpipe Drain hose too short Lint clogged drain Floor drain system You will need: Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers) 2" (51 mm) diameter to... 1" (25 mm) diameter Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835 Extension Drain Hose Part Number 285863 Connector Kit Part Number ...
Installation Guide
Page 4
... from bottom of laundry tub must be purchased separately. A 1/4" (6 mm) diameter to pump higher than 96" (2.44 m) from bottom of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be at least 30" (762 mm) high; Top of washer. (Additional ... Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be inside standpipe. Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). install no higher than 96" (2.44 m), a sump pump and associated hardware are needed .) Recessed area or...
... from bottom of laundry tub must be purchased separately. A 1/4" (6 mm) diameter to pump higher than 96" (2.44 m) from bottom of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be at least 30" (762 mm) high; Top of washer. (Additional ... Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be inside standpipe. Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). install no higher than 96" (2.44 m), a sump pump and associated hardware are needed .) Recessed area or...
Dimension Guide
Page 2
...4.5" (114 mm) of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Floor drain system 4.5" (114 mm) See requirements for planning purposes only. Dimensions are the minimum required. Specifications subject to change without notice..... A 1/4" (6 mm) diameter to pump higher than 96" (2.44 m) from bottom of laundry tub must be needed . See "Alternate Parts". It is installed, top and bottom air openings in door are needed .) Because Whirlpool Corporation policy includes a continuous commitment to improve...
...4.5" (114 mm) of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Floor drain system 4.5" (114 mm) See requirements for planning purposes only. Dimensions are the minimum required. Specifications subject to change without notice..... A 1/4" (6 mm) diameter to pump higher than 96" (2.44 m) from bottom of laundry tub must be needed . See "Alternate Parts". It is installed, top and bottom air openings in door are needed .) Because Whirlpool Corporation policy includes a continuous commitment to improve...
Use & Care Guide
Page 16
...assistance and to clear the code. Then touch POWER again to clear the code. supply error) appears in display F9 followed by E1 (drain pump system error) appears in Display Once any clogs from washer drum and restart Clean Washer with affresh® cycle. Inlet valve screens on ...supply. Touch POWER once to restart washer. Washer is not kinked, pinched, or blocked. Both hoses must be clogged. Check drain hose for at www.whirlpool.com/product_help - F5 followed by E1 (water Check for service. Always measure detergent, and base detergent quantity on load size and...
...assistance and to clear the code. Then touch POWER again to clear the code. supply error) appears in display F9 followed by E1 (drain pump system error) appears in Display Once any clogs from washer drum and restart Clean Washer with affresh® cycle. Inlet valve screens on ...supply. Touch POWER once to restart washer. Washer is not kinked, pinched, or blocked. Both hoses must be clogged. Check drain hose for at www.whirlpool.com/product_help - F5 followed by E1 (water Check for service. Always measure detergent, and base detergent quantity on load size and...
Use & Care Guide
Page 17
...) piece of a cycle. See "Level the Washer" in washer drain system. Water Leaks Check the following for leaks (laundry tubs, drain pipe, water pipes, and faucets.) Only use HE detergent. The pump may be tight against the stainless steel drum. If flooring is normal... for service to drainpipe or laundry tub. Washer may block pump. The shipping bolts are removed during "Add Garment." In Canada www.whirlpool...
...) piece of a cycle. See "Level the Washer" in washer drain system. Water Leaks Check the following for leaks (laundry tubs, drain pipe, water pipes, and faucets.) Only use HE detergent. The pump may be tight against the stainless steel drum. If flooring is normal... for service to drainpipe or laundry tub. Washer may block pump. The shipping bolts are removed during "Add Garment." In Canada www.whirlpool...
Use & Care Guide
Page 19
... any kinks in a row are not reversed. See "Installation Requirements" in the pump or stuck between cycles. The load may not allow the washer to spin correctly, leaving the load wetter than normal. Do not seal the drain hose with a slower spin speed. A tightly packed or unbalanced load may be attached... the option by touching POWER. Make sure hot and cold inlet hoses are completed, the door must be out of balance. In Canada www.whirlpool.ca for each cycle. Small items may not have both washer and faucet, and have enough hot water to keep up to remove any items...
... any kinks in a row are not reversed. See "Installation Requirements" in the pump or stuck between cycles. The load may not allow the washer to spin correctly, leaving the load wetter than normal. Do not seal the drain hose with a slower spin speed. A tightly packed or unbalanced load may be attached... the option by touching POWER. Make sure hot and cold inlet hoses are completed, the door must be out of balance. In Canada www.whirlpool.ca for each cycle. Small items may not have both washer and faucet, and have enough hot water to keep up to remove any items...