AIWA CDC-Z107 Support Question
AIWA CDC-Z107 Support Question
Find answers below for this question about AIWA CDC-Z107.Need a AIWA CDC-Z107 manual? We have 1 online manual for this item!
Question posted by Anonymous-111301 on May 14th, 2013
How Do I Turn The Power Off Once Its One
i got it to turn on but once the player is on it wont shut off. what could be my problem
Current Answers
Answer #1: Posted by jonmr001 on May 14th, 2013 4:18 PM
jonmr001
Member since:
April 23rd, 2013 Points: 104,040
Member since:
April 23rd, 2013 Points: 104,040
You have to hold the button down for few seconds.....push and hold the power/mute button down and count to 4........
If this helps please dont forget to accept....thanks!
Thanks for posting on Help Owl! Please remember to "Accept" if I have helped you with your issue. Have an OUTSTANDING day!
Related AIWA CDC-Z107 Manual Pages
Service Manual - Page 1
CDC-Z107 YU
SERVICE MANUAL
STEREO CAR CD RECEIVER
BASIC CD MECHANISM : TN-CCD1001-113J
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual" of CDC-Z107, (S/M Code No. 09-99B-422-4T1). S/M Code No. 09-002-422-4R1
REVISIODNATA
Service Manual - Page 2
...
45 W x 4 channels
TAPE/MD IN input
Input Sensitivity (load impedance)
TAPE/MD IN
500 mV (10 kΩ)
GENERAL
Power Supply Voltage
14.4 V (11 to 16 V allowable),
DC, negative ground
Load Impedance
4 Ω
Tone Control
Bass ±10 dB at 100 Hz
... S/N Ratio Wow/Flutter
17 Hz - 20 kHz +0/-3 dB More than 80 dB More than 65 dB More than 85 dB Unmeasurable
AUDIO SECTION Max.
Service Manual - Page 3
... CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. ADVARSEL Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. This Compact Disc player is located on the rear exterior. VARNING! The CLASS 1 LASER PRODUCT label is classified as a CLASS 1 LASER product. PICK-UP ASSY P.C.B
- 3 - PROTECTION OF EYES FROM...
Service Manual - Page 23
... low
40
A-MUTE
O
Audio mute signal output.
41
POWER CONT
O
Power control signal output.
42
ST-BY MUTE
O
ST-BY mute signal output.
43
POWER MUTE
O
Power mute signal output.
44...diode matrix output.
27 ~ 30
K3 ~ K0
I
Sub-code Q output standby input terminal.
- 23 - Power supply.
32
NC
- O
Thread motor control terminal.
37
RW
O
RW disc control. Not connected.
4
E-VOL...
Service Manual - Page 24
... detection. I
IF count signal input (FM / AM).
- OFF=fault mode. I
ACC (accessory power) ON/ OFF input. Not used .
-
Connected to GND.
I
CD test mode. I
Remote controller ...used . Not connected. I
System reset.
Not connected.
I
Leading motor start detection. Power supply. I
External mute control.
I
Voltage input for FM / AM).
-
O
Error...
Service Manual - Page 27
...31 32 33
VDD
- Output 4.3218 MHz when the phase is a Schmitt input. Digital system power supply. C2 flag output. Left channel output. Left channel groud. (Must be connected to three-...command. Tracking gain switching output. Increase the gain when low. Test input. Left channel power supply. Slice level control EFM signal input. EFM data playback clock monitor. Output a...
Service Manual - Page 28
...output.
Right channel mute output./ General purpose input/ output. Crystal oscillator power supply. Crystal oscillator ground. (Must be connected to 0V.) Chip seledt ...O
4.2M
O
TEST5
I
CS
I
TEST1
I
Description Right channel ground. (Must be set low briefly after power is Schmitt input. Connections for a 16.9344 MHz crystal oscillator element. Reset input. MUTER/CONT8 O
XVDD
-...
Service Manual - Page 29
... a low impedance.
- Data transfer is enabled at a low impedance. VSS as a troubleshooting against power ripples. The frount and rear sides can be driven at a low impedance. Not used .
- ...control output. Must be driven at a low impedance.
- I
Super bass input.
O
Fader outputs. Power supply.
- 29 - Chip enable.
from "H", and each analog switch is written in the tone ...
Service Manual - Page 30
...
64
DI
O
Serial data interface pin;
chip enable.
63
CL
O
Serial data interface pin;
Power supply. Description
IC, LC75853NW
Pin No.
data transferred.
- 30 -
Test pin. (Connected to ...No. 40 41 42 43 44
Pin Name TP(R) TUN(R) CD(R) AUX(R) RSELO
I/O
I
Key scan inputs. Power supply. (Connected to GND.)
56
VDD
- Pin Name
I/O
Description
1 ~ 40
S1 ~ S40
O
LCD ...
Service Manual - Page 31
...8226; Step 2 : For CD-R RF Gain is up
against Step 1 • Step 3 : For CD-R Laser Power Up
against Step 2
Contents • Start TEST MODE • Confirm APC circuit • Laser current measurement •...(red) and BACKUP (yellow) of the MAIN C.B
IC701 (LC72358N-9910) and switch on the power.
1-3 CD Test Mode Functions
MODE
Keys to operate
Start Mode
Search Mode RANDOM
Play Mode REP ...
Similar Questions
Cdc-x2170 Reset Button
Is there a reset button & how should i do that?
Is there a reset button & how should i do that?
(Posted by fychkroy 10 years ago)
I Need A Pinout Diagram For A Cdc-x144
no Harness But Need To Wire The Radio In Hard
no Harness But Need To Wire The Radio In Hard
(Posted by JIMMYKAYLA77 10 years ago)
Wiring Harness For One Of The Aiwa Cdc-x517myu?
Where can I find a wiring harness for this stereo? Or what wiring harness would fit this stereo?
Where can I find a wiring harness for this stereo? Or what wiring harness would fit this stereo?
(Posted by Hotrod8000 10 years ago)