D-Link DES-3226 Support Question
D-Link DES-3226 Support Question
Find answers below for this question about D-Link DES-3226 - Switch.Need a D-Link DES-3226 manual? We have 3 online manuals for this item!
Question posted by Anonymous-121522 on September 26th, 2013
How To Reset The Des-3226l To Factory Default
How to reset the des-3226l to factory default. There is no pin hole on the right side of this switch
Current Answers
Related D-Link DES-3226 Manual Pages
Product Manual - Page 3
Factory Reset...43 Restart System...44 Basic Setup...44 Stacking Information...48 Configure Ports ...51 Port Security...53 Traffic Segmentation...55 SNTP and Time Settings ...57 Network Management ...60 SNMP Settings ...60 Switch Utilities...66 TFTP Utilities...66 Advanced Setup...69 Configuring VLANs...69 Asymmetric VLANs...72 Configure QoS (Quality of Service)...73 Bandwidth...
Product Manual - Page 4
... end stations, servers and hubs.
• All ports can auto-negotiate (NWay) between 10Mbps/ 100Mbps, half-duplex or full duplex and flow control for halfduplex ports.
• One front panel slide-in an environment where traffic on the network and the number of the DES-3226S.
DES-3226S Layer 2 Fast Ethernet Switch User's Guide
1
Introduction
This...
Product Manual - Page 8
...Switch's power supply will remain ON if
there is turned ON • The console LED indicator will momentarily blink. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
Power on
The DES-3226S Switch ... precaution in .
5 This blinking of the LED indicators represents a reset of a power failure, unplug the Switch. After the power Switch is OFF • The 100M LED indicator may be used with...
Product Manual - Page 9
... a connection to end stations, servers and hubs.
Rear Panel
The rear panel of the Switch The AC power connector is a standard three-pronged connector that supports the power cord. Rear panel view of the Switch contains an AC power connector. Figure 3 - 2. Figure 3 - 1.
DES-3226S Layer 2 Fast Ethernet Switch User's Guide
3
Identifying External Components
This chapter describes...
Product Manual - Page 20
..., the cable, Switch conditions, and connections. Switch to Hub or Switch
These connections can be sure to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable (be accomplished at any of the twenty-four ports of the NIC. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
4
Connecting the Switch
This chapter describes how to connect the DES-3226S to End...
Product Manual - Page 21
... Ethernet Switch User's Guide
Switch Stack Connections
Up to eight DES-3226S Switches (with any failure of the Switches in the composition of the Master Switch). An example stacking port interconnection is made such that can configure and manage all of a stacking port will cause the entire stack to an OUT port on the other Switch. The default settings...
Product Manual - Page 22
... connection, meaning that used to the RS-232 DCE console port of the Switch. The console port is set at the factory for the following configuration:
• Baud rate:
9,600
• Data width...These components allow the Switch to the Switch using to make use of the Switch performed over the network (in the next chapters. If you are identical. The DES-3226S contains a CPU, memory...
Product Manual - Page 23
... not necessary to change occurs in the structure or composition of a stacked group to operate in either capacity. When the stacking mode is enabled by default. If a DES-3226S Switch stack is possible to load configuration files saved from a stacked group. It may be forced into master mode. After restarting, the designated master unit...
Product Manual - Page 24
... DGS-3312SR does not restart when a link or Switch failure occurs. Managing Switch Stacks
Multiple DES-3226S Switches equipped with stacking modules may be chosen automatically as each Switch in the stack and reboot as a standalone device with the DGS-3212SR or DGS-3312SR, the default settings of the DES-3226S assign slave status and the unit number is...
Product Manual - Page 25
... settings have already been set to the default auto-stacking mode and therefore no changes are installed so it is also uplinked to the backbone via the stacking ports. This should be the slave. Switch B automatically assume slave status. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
NOTE: For a Switch that has previously acted in a standalone...
Product Manual - Page 28
...port as shown below . The Switch's default IP address is also assigned a unique MAC address by the factory. The Switch is 10.90.90.90. The Switch IP address may alternatively be known...
2. You can change the default Switch IP Address to the Switch's web-based management agent.
25 DES-3226S Layer 2 Fast Ethernet Switch User's Guide
Switch IP Address
Each Switch must be assigned its own ...
Product Manual - Page 29
...SHA-96 or HMAC-MDA-96 authentication levels). DES-3226S Layer 2 Fast Ethernet Switch User's Guide
SNMP Network Management
The Simple ... Switch has been powered up and initialized such that software settings are reconfigured and hardware systems are given certain rights ... the Switch.
• Warm Start This trap signifies that occur on the network). You may receive traps from a factory reset in ...
Product Manual - Page 41
...of the Switch.
NOTE: The Factory default IP ...address for the device. Figure 6- 1. This opens the management module's main page. The URL in the web-based manager are explained below.
38 In the page that opens, click on your Switch simply run the browser you have installed on the Login hyperlink. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
Configuring the Switch...
Product Manual - Page 45
...Trap Stations
Yes
Update Firmware and Configuration Files
Yes
System Utilities
Yes
Factory Reset
Yes
Reboot Switch
Yes
User Account Management
Add/Update/Delete User Accounts Yes
View User...button. The following screen will be available to restart the Switch before rebooting the Switch.
Saving Changes
The DES-3226S has two levels of user privileges: Admin and User. When...
Product Manual - Page 46
DES-3226S Layer 2 Fast Ethernet Switch User's Guide Click the Save Configuration button to save these default values to the Switch's non-volatile RAM. The following dialog box will return the Switch's configuration to the state it was when it left the factory. NOTE: Only the Reset System option will enter the factory default parameters into the current configuration, but do...
Product Manual - Page 48
DES-3226S Layer 2 Fast Ethernet Switch User's Guide
Switch Information
Click the Switch Information link in the Basic Setup folder) to open the menu illustrated below. The Switch Information window shows which it is installed on the Switch, you can leave the default address in -band communication. if necessary. The fields listed under the New Switch IP Setting heading are...
Product Manual - Page 49
... next reboot. Figure 6 - 9. Basic Switch Setup NOTE: The factory default IP address for the Switch is 10.90.90.90 with a subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0.
46
DES-3226S Layer 2 Fast Ethernet Switch User's Guide To use the BOOTP or DHCP protocols to assign the Switch an IP address, subnet mask, and default gateway address: Use the...
Product Manual - Page 51
... version number of the Switch assigned by the factory. The Stacking Module's Front Panel The Stack No. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
Stacking Information
When DES-3226S Switches are properly interconnected in a stacked group, information about the stack is displayed in the total count. The default settings allow stacking with other DES-3226S Switches in a ring topology...
Reference Manual - Page 11
... on the switch. Figure 1-2. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
The switch is configured on the switch and contains all of the ports on the switch,
Introduction
11
The System interface can also be used initially to assign a range of IP addresses to the switch must be managed with the web-based manager. By default, an IP...
Reference Manual - Page 51
...Only administrator-level users can issue this command. DES-3226S Layer 2 Fast Ethernet Switch User's Guide
reset
Purpose Syntax Description Parameters
Restrictions
Used to reset the switch to their default values:
DES3226S:4#reset config Command: reset config
Basic Switch Commands
51
All other parameters are restored on the switch except for the IP address,.
If no parameter...
Similar Questions
How To Reset Dir-601 Router Default Ip Address
(Posted by klbtorre 10 years ago)
How To Reset Dir-601 To Factory Default
(Posted by ssainju1234 10 years ago)
Cost Of Des 3226s D Link Switch
cost of des 3226s d link switch?
cost of des 3226s d link switch?
(Posted by thopatesagar09 11 years ago)
