Dell PowerEdge 2900 Support Question
Dell PowerEdge 2900 Support Question
Find answers below for this question about Dell PowerEdge 2900.Need a Dell PowerEdge 2900 manual? We have 9 online manuals for this item!
Question posted by kemynot on April 24th, 2014
How To Remove Power Supply Dell 2900
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerEdge 2900 Manual Pages
Installing a SATA Optical Drive - Page 6
... Figure 1-3.
a Route the cable through the power cable cutout in a PowerEdge 1950 Drive Tray 2 3
1 4
5
1 optical drive 3 SATA power cable 5 optical drive carrier
2 SATA cable 4 carrier latch
Installing the SATA Optical Drive -
Installing a SATA Optical Drive in the fan bracket and follow the power cable routing to the power supply connector. b Bend the cable toward the chipset...
Installing a SATA Optical Drive - Page 7
... Card" in your Hardware Owner's Manual.
7 Reconnect the system to the power supply connector.
See "Closing the System" in the PowerEdge 1950 2
1
3
4
6
5
1 SATA data cable 3 chipset shroud 5 SATA power cable
2 SATA_A connector on the system and attached peripherals. Installing a SATA Optical Drive
7 PowerEdge 2970 or 2950
1 Insert the optical drive tray into the system until...
Installing a SATA Optical Drive - Page 9
... one end to the optical drive and the other to power and turn on the system and attached peripherals.
9 Replace the cooling shroud. For a PowerEdge 2900 system, connect to the SATA connector on the system backplane. For a PowerEdge 1900 system, connect to an available power supply cable.
5 Replace the center fan bracket. Installing the SATA Optical...
Installing a SATA Optical Drive - Page 10
... turn on system board
8 Reconnect the cables to the SAS controller daughter card.
9 Close the system. See "Closing the System" in a PowerEdge 2900 or 1900
3
2
4
5 1
1 optical drive 3 SATA data cable 5 SATA power connector on SAS
backplane (PowerEdge 2900 only)
2 SATA power cable 4 SATA connector on the system and attached peripherals.
10
Installing a SATA Optical Drive Figure 1-5.
Getting Started Guide - Page 5
... processors. The system also features redundant memory, which is supported with the 1x2 flexbay bracket removed.
• An optional single, 1.44-MB, 3.5-inch diskette drive.
• An optional...you must order the processor upgrade kits from Dell. NOTE: DVD devices are installed.
• Support for up to two hot-pluggable, 930-W power supplies in the peripheral bay using the optional ...
Hardware Owner's Manual (PDF) - Page 4
... Drive 56
Replacing a Hard-Drive Carrier 58 Removing a Hard Drive From a Hard-Drive Carrier 58 Installing a SAS Hard Drive Into a SATAu Drive Carrier 58 Installing a SATA Hard Drive Into a SATA Drive Carrier 59 Installing a SATA Hard Drive and Interposer Card Into a SATAu Hard-Drive Carrier 60
Power Supplies 62 Removing a Power Supply 62 Installing a Power Supply 63
4
Contents
Hardware Owner's Manual (PDF) - Page 5
Removing the Power Supply Blank 64 Installing the Power Supply Blank 64
Fans 64 Removing and Installing a Fan 65 Removing or Installing the Cooling Shroud Fan 66
Expansion Cards 68 Installing an Expansion Card 68 Removing an Expansion Card 70
Internal SCSI Tape Backup Unit 70 Removing an Internal SCSI Tape Backup Unit 70 Installing an Internal SCSI Tape Backup...
Hardware Owner's Manual (PDF) - Page 7
... 120 Troubleshooting a Damaged System 121 Troubleshooting the System Battery 122 Troubleshooting Power Supplies 122 Troubleshooting System Cooling Problems 123
Troubleshooting a Fan 123 Troubleshooting System ... the Microprocessors 133
5 Running the System Diagnostics
Using Server Administrator Diagnostics 135 System Diagnostics Features 135 When to Use the System Diagnostics 135 ...
Hardware Owner's Manual (PDF) - Page 21
...a component that resides in PCI slot #.
See "Troubleshooting Power Supplies" on page 122. See "Troubleshooting Power Supplies" on page 122. PS # Predictive
Power supply voltage is faulty. PCI PERR B## D## F##
PCI PERR Slot #
The system BIOS has reported a PCI parity error on page 147. About Your System
21
Remove and reseat the PCI expansion cards.
See "Getting...
Hardware Owner's Manual (PDF) - Page 26
.... In contrast, you of messages indicating multiple voltage faults, you might be able to notify you might determine that is a failing power supply. CAUTION: Only trained service technicians are authorized to remove the message from the electrical outlet; For example, if you receive a series of a possible problem with sensors, such as temperature, voltage...
Hardware Owner's Manual (PDF) - Page 53
... are installing a hot-plug component such as a cooling fan or power supply, turn off the system and attached peripherals, and disconnect the system from the system. CAUTION: Whenever you need to lift the system, get others to assist you are authorized to remove the system cover and access any of the chassis. See...
Hardware Owner's Manual (PDF) - Page 62
...: On a rack system, you can leave the system running and proceed to an AC power source. Removing a Power Supply
NOTICE: The system requires one power supply is installed, it interferes with power supply removal. See Figure 3-10.
62
Installing System Components If only one power supply for the system to unlatch and lift the cable management arm if it must be...
Hardware Owner's Manual (PDF) - Page 63
... tab snaps into the chassis until the power supply is functioning properly (see Figure 1-5). Installing and Removing a Power Supply
1
3
2
4
6
5
1 power supply 4 power supply blank
2 handle 5 screw
3 tab 6 locking tab
Installing a Power Supply
1 If you may need to recognize the power supply and determine its status. The power-supply status indicator turns green to the cable...
Hardware Owner's Manual (PDF) - Page 64
... module cooling fans:
- Figure 3-11 shows the positions and identification numbers of the memory cooling shroud (fan 4) -
See Figure 3-10. Remove the power supply blank only if you to clear the bay, and remove from the chassis. Rotate the blank into the slot in a non-redundant configuration. NOTICE: To ensure proper system cooling, the...
Hardware Owner's Manual (PDF) - Page 111
See Figure 3-34.
10 Remove the power distribution board from the power distribution board. Installing System Components
111 See "Removing a Power Supply" on page 107.
6 Disconnect all of a work surface.
4 Open the system. See "Opening the System" on page 53.
5 Perform all cables connecting the system board ...
Hardware Owner's Manual (PDF) - Page 121
...removed. Troubleshooting a Damaged System
Problem • System was dropped or damaged.
See "Running the System Diagnostics" on page 53. 2 Ensure that the following components are properly installed:
• Expansion cards • Power supplies... start properly, see "Getting Help" on page 135. See "Using Server Administrator Diagnostics" on page 147. If the tests fail, see "Getting...
Hardware Owner's Manual (PDF) - Page 122
... Troubleshooting the System Battery
Problem • System message indicates a problem with the power supplies. If the problem is turned off the system and disconnect it from the electrical... Reconnect the system to remove the system cover and access any procedure, see "Getting Help" on page 135. 2 Locate the faulty power supply.
See "Using Server Administrator Diagnostics" on page...
Hardware Owner's Manual (PDF) - Page 123
... issues a fan-related error message.
See "Power Supplies" on page 62. 5 Install a new power supply.
See "Removing a Power Supply" on page 62.
Action Ensure that the power supply is properly installed by removing and reinstalling it is removed or has failed. One power supply must be installed for the system to recognize the power supply and to operate. NOTICE: You can cause...
Hardware Owner's Manual (PDF) - Page 177
...(rack) installing, 53 removing, 50
bezel (tower) installing, 53 peripheral bay panel, 52 removing, 51
blank hard drive, 56 power supply, 64
BMC. See ...Dell contacting, 152
diagnostics checklist, 151 testing options, 136 when to use, 135
DIMM installing, 85 removing, 87 sockets, 82
diskette drive drive carrier, 76 installing, 76 removing, 74 troubleshooting, 126
drive blank installing, 56 removing...
Hardware Owner's Manual (PDF) - Page 180
...messages LCD, 18 systems management, 26
support contacting Dell, 152
system board connectors, 141 installing, 109 jumpers, 139 removing, 107
system cooling troubleshooting, 123
system features ...Index removing (continued) hard drive from a drive carrier, 58 hard drives, 56 memory, 87 optical drive, 73 peripheral bay panel (tower), 52 power distribution board, 110 power supply, 62 power supply ...
Similar Questions
E122b 0.9 Over Volt Instruction On Dell Power Edge 2900
E122B 0.9 over volt instruction on Dell power Edge 2900, server not start
E122B 0.9 over volt instruction on Dell power Edge 2900, server not start
(Posted by mspshahriar 8 years ago)
How To Install Dell Redundant Power Supply Poweredge 2900
(Posted by mikkaneva 9 years ago)
How To Replace Power Supply Dell Poweredge 2900
(Posted by cpdcjlars 10 years ago)
