Dewalt D55168 Support Question
Dewalt D55168 Support Question
Find answers below for this question about Dewalt D55168.Need a Dewalt D55168 manual? We have 4 online manuals for this item!
Question posted by elliottsandra57 on November 30th, 2020
Dewalt 55168 Type 2
builds tp 20 psi and stops and continues running
Current Answers
Answer #1: Posted by INIMITABLE on November 30th, 2020 2:12 PM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,069,620
Member since:
April 3rd, 2020 Points: 2,069,620
Reciprocating units need time to stop and cool off, or the internals will become damaged. When damage occurs, the compressor can experience valve failures, causing the compressors to run constantly. ... With modulation, a control valve chokes off the inlet of the compressor to control the flow and pressure.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Dewalt D55168 Manual Pages
Instruction Manual - Page 2
...
Pump/Motor Specifications
Voltage: Single Phase 120V Minimum branch circuit requirement: 15 A Fuse Type: Time delay
Specifications
MODEL WEIGHT HEIGHT WIDTH LENGTH AIR TANK CAPACITY (GALLONS) APPROX CUT... A G
D E
F
H Safety Valve H. Pressure Regulator E. CUT-OUT PRESSURE SCFM @ 90 PSI (620.5 kPa)
D55168 88 lbs. (39.92 kg) 41.75" (1060.5mm) 19.0" (482.6 mm) 21.25 (539.8...
Instruction Manual - Page 3
...THESE INSTRUCTION
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)
Important Safety Instructions
WARNING: Do not operate this...read and understand this type of work with approved safety equipment, always wear OSHA/MSHA/NIOSH approved, properly fitting face mask or respirator when using air tools, basic safety precautions ...
Instruction Manual - Page 4
... of fresh air to use . Read and follow the safety instructions provided on top of compressor.
• Operate compressor in an open area at least 20 feet (6.1 m) away from spray area. English
• If electrical sparks from compressor come into contact with flammable vapors, they may ignite, causing fire or explosion...
Instruction Manual - Page 5
... Follow the equipment manufacturers recommendation and never exceed the maximum allowable pressure rating of air tools, spray guns, air operated accessories, tires, and other electrically powered device, If it ... following conditions could result in the government section of a phone book or call 1-800-4-DEWALT for units with air tanks greater than 6 inch diameter) according to explode or fly ...
Instruction Manual - Page 6
... at other people or animals.
• Always turn the compressor off and bleed pressure from the air hose and air tank before attempting maintenance, attaching tools or accessories. WARNING: RISK OF HOT SURFACES
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Touching exposed metal such as the compressor head, engine head...
Instruction Manual - Page 7
... damaged or missing parts or attempting to repair compressor with protective shrouds removed can expose you or
this product should be performed by a DEWALT factory service center or a DEWALT authorized service center. instructions and warnings in a stable secure position to you to reach high locations. others.
• Become familiar with missing, broken...
Instruction Manual - Page 8
.... The cooling system is working when air is normal for a few seconds. Working air is running ,
less than the pressure switch cut -in pressure. C
OUTLET PRESSURE GAUGE
PRESSURE RELEASE VALVE...reaches the factory set pressure (slightly Maintenance.
When the motor stops running or after the unit
reaches "cut-out" pressure. 8 It stops the motor when the air tank simple and easy. DRAIN ...
Instruction Manual - Page 9
...understood, or
if in accordance
L
with a grounded outlet
(K). Ensure regulated pressure gauge reads 0 PSI (0 kPa). 2.
Allow the motor to prevent hose whip. 1.
If these grounding instructions are signs...correct branch circuit receptacle. 4. Do not use . Ensure regulated pressure gauge reads 0 PSI (0 kPa). 2. This air compressor must be sure it does not fit the available...
Instruction Manual - Page 11
.... 4.
PREPARATION FOR USE
Pre-Start Checklist (Fig. 1)
1. Ensure air tank is not connected to ground. Read the instructions for air tools and accessories. Check the manufacturer's maximum pressure rating for the air tools and accessories. Initial Set-up
a ramp.
1. Serious damage may require filtered air. Ensure the drain valve (H) is in the...
Instruction Manual - Page 12
...unit may require filtered air. The compressor will stop .
7. Run the compressor for the air tool or device.
3. Follow Pre-Start Checklist under...PSI (0 kPa).
NOTE: All compressed air systems contain maintenance parts (e.g., oil, filters, separators) that could be performed by a DEWALT factory service center or a DEWALT authorized service center.
12 Compressed air will stop...
Instruction Manual - Page 13
...protection as debris can cause stains. 3.
Ensure On/Off switch (A) is
at 0 PSI (0 kPa). Place a suitable container under the drain valve to the fully open position. 7. When air tank...is loud when draining. Drain water from air tank. 6.
more frequent in accordance with the same type of bursting. Outlet tube, pump head,
and surrounding parts are very hot, do not touch (see...
Instruction Manual - Page 14
CAUTION: The use of any other accessory not recommended for use with your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT.
Full One Year Warranty
DEWALT heavy duty industrial tools are missing, call 1-800-4-DEWALT for all service calls: Model Number Serial Number Date and Place of unsafe operation...
Instruction Manual - Page 15
... -in any given hour.
15 PSI: Pounds per minute; It builds to prolong the life of your air tank from electrical panel to outlet. However, to a certain high pressure before the motor automatically shuts off, protecting your air compressor, it is turned on and begins to run more of running continuously. Cut-Out Pressure: When...
Instruction Manual - Page 16
...12,23
Regulator knob has continuous air leak 13
Regulator will not shut off air outlet 13
Motor will not run ...6,14,15,16,17,18,19,20,21
Squealing Sound ...22...cut-out pressure
off contact a DEWALT factory service center or a DEWALT
authorized service center.
2
Pressure switch cut-out too high
Contact a DEWALT factory service center or a DEWALT authorized service center.
3
Tube ...
Instruction Manual - Page 17
... air tank can rupture or explode.
NOTE: Adjust the regulated pressure under Features. Replace air hose. Remove, clean or replace. Tighten fittings. Contact a DEWALT factory service center or a DEWALT authorized service center. Decrease amount of bursting. If it is higher than the CFM or pressure supplied by pulling on ring.
Motor will...
Instruction Manual - Page 18
... wrong length or gauge
17
Loose electrical connections
18 Possible defective motor
19 Paint spray on internal motor parts
20
Pressure release valve on its own branch circuit.
Contact a DEWALT factory service center or a DEWALT authorized service center. Check wiring connection inside pressure switch and terminal box area. Bleed the line by pushing...
Instruction Manual - Page 56
... on the surface of lozenge-shaped humps on the handgrip; the "D" shaped air intake grill; and the array of the tool. A18764 D55168 Copyright © 2006 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 (AUG06) Form No.
Parts Diagram - Page 2
... Reserved. Page 1 Item Number
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
Part Number
Parts List for current parts information. Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
A16537
TANK ASSEMBLY
1
N008517
WHEEL
2
A01194
BOLT .375-16X2.38 UN
2
SSF...
Parts Diagram - Page 3
... LA-2876 N018445 A19131 N094098
Parts List for current parts information. Parts list, pricing, and availability subject to change. Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
REGULATOR BONNET
1
KNOB
1
REGULATOR/MANIFOLD
1
GAUGE
1
FITTING
1
GAUGE
1
MICRO PRESS.
Parts Diagram - Page 4
... N021229
Parts List for current parts information. Page 3 Parts list, pricing, and availability subject to change. All Rights Reserved. Please visit www.dewaltservicenet.com for D55168 Type 5
Description
Qty Required
PLUG PIPE
2
BODY QC .250 IND .25
1
BRUSH
2
BRUSH SPRING
2
BELT
1
FAN
1
SCREW
1
MOTOR PULLEY
1
FLYWHEEL
1
CONN ROD/PISTON ASSY
1
SCREW
1
IDLER...
Similar Questions
Compressor Won't Build Pressure. I Replaced The Manifold. The Compressor Goes
compressor won't build pressure. I have replaced the manifold and it will only go to about 40 psi. I...
compressor won't build pressure. I have replaced the manifold and it will only go to about 40 psi. I...
(Posted by Tbassgolf 2 years ago)
Will Not Build Over 30 Lb. Never Quit Running
Will not build over 30 lb. Of pressure keeps running
Will not build over 30 lb. Of pressure keeps running
(Posted by thomasdavis359 6 years ago)
Part Number For Compression Ring On D55168 T5
Ok I have a D55168 T5 The compression ring in the sleeve has a blown spot so I need to replace it I ...
Ok I have a D55168 T5 The compression ring in the sleeve has a blown spot so I need to replace it I ...
(Posted by Anonymous-159859 7 years ago)
