Home » Epson » Dot Matrix Printers » Epson LQ 1050

Epson LQ 1050 Support Question

Find answers below for this question about Epson LQ 1050 - B/W Dot-matrix Printer.
Need a Epson LQ 1050 manual? We have 5 online manuals for this item!

Epson Overview Questions Manuals Reviews Videos Research

Question posted by shaileshrathore9977 on March 23rd, 2023

5 Time Beep And All Light Onn Error

when i try to start my printer wep lq 1050+ .. head freeze at on left side and my printer make 5 time beep and all lights on. plz help what is the problem

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by shlokuprit on March 23rd, 2023 2:54 AM

This answer was accepted by the poster of the original question.

shlokuprit

Member since:
November 28th, 2020

Points: 35,590

1,100
points

Here are a few things you can try to troubleshoot the problem:

1. Turnoff the printer and unplug it from the power source. Wait for a few minutes before plugging it back in and turning it on again. This can sometimes reset the printer and clear the error.

2. Check for any paper jams or obstructions in the printer. Make sure there is no paper or debris stuck in the printer mechanism that could be preventing it from functioning properly.

3. Check the ink cartridges and make sure they are properly installed and not low on ink. If the ink cartridges are empty, replace them with new ones.

Answer #2: Posted by SonuKumar on March 23rd, 2023 9:18 AM

SonuKumar

Member since:
May 9th, 2021

Points: 16,653,150

100
points

https://www.manualslib.com/manual/418003/Epson-Lq-1050-B-W-Dot-Matrix-Printer.html?page=31

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Epson LQ 1050 Manual Pages

Product Support Bulletin(s) - Page 1

... stop until the printhead cools down. NOTE: Most of the beeps issued by product name. LQ-500, LQ-510, LQ-1010, LQ-850, LQ-950, LQ-1050, L1000, AP-4000, AP-4500 1 beep: BEL code (.5 sec beep) 1 beep: A Control Panel setting is over heated. EPSON Product Support Bulletin Subject: 24 Pin Printer Error and Beep Codes Date: 4/3/91 Page(s): 1 of .1 second duration with a .1 second...

Product Support Bulletin(s) - Page 3

... Page: 3 of 4 LQ-2500 NOTE: Printers with LCD displays use error messages along with beeps to inform the user of problems. The following messages will help you to CGROM 03 EEROM read/write error 10 Abnormal carriage movement LQ-2550 1 beep: BEL code 3 beeps: Paper End detected 5 beeps: Abnormal carriage movement (.5 sec. pause between beeps) 5 beeps: Platen Gap adjustment...

User Manual - Page 3

...and Resolve Radio-TV Interference Problems." Relocate the printer with respect to the use ... may be determined by the Federal Communications Commission helpful: "How to comply with the limits for...the user is encouraged to try to correct the interference by one interface...the dealer or an experienced radio/television technician for errors or omissions. Copyright 0 1988 by any liability assumed...

User Manual - Page 9

... show only the LQ-1050. You will also find a glossary of applications software, graphics, and user-defined characters. vu. .1. At the back of the manual is necessary for their widths. Chapter 4 contains information designed to help you are most from your printer. This section includes advice on setting and operating the LQ-850, LQ-950, and LQ-1050 printers.

User Manual - Page 45

...again. A Pressing the LOAD/EJECT button once may not feed the 1. If the PAPER OUT light does not come on when the paper is still attached to the single sheet position. 2-13 With... to three times. Push the paper release lever back to the tractor, but no longer in the paper path. The paper is completely out of the printer and into a standby position. The PAPER OUT light comes on ...

User Manual - Page 49

...position 4 or higher. When tPhAeRpTapelirghtht iccokmneesss lever is on if the lever is reduced. To help the orange MyUouLTcIh-ecPkARthTe position light on of the print head. Continuous printing with the lever set to printing on special types of paper, see the table...the printing speed is set at a position higher 8 than normal paper can damage the print head. 2-17 MULTI-

User Manual - Page 56

..., or initialize the printer. 0 MULTI-PART S&c Type 0 POWER 0 READY 0 PAPER OUT FORM FEED - The orange indicator lights show which font - The orange indicator light shows the selected pitch...installed, these , the printer beeps three times. 3-4 Operating the Control Panel SelecType The settings you select using the SelecType panel remain valid even after you try to select either SLOT...

User Manual - Page 57

... on the printer, you can start the LQ's self test. Self test By holding down the FORM FEED or LINE FEED button while you turn on the printer, you can move the paper 1/180th of the LQ also gives you access to diagnose many problems. See the section on line and the orange indicator light is flashing...

User Manual - Page 65

Each time you hold the button down, the paper moves continuously in 1/180 of an inch increments. Using micro adjustment on continuous paper establishes a new loading position that remains valid even after the printer is turned off or reset. When using micro adjustment on light starts to set loading position, the printer beeps and micro-adjustment feeding...

User Manual - Page 114

... solutions This section lists possible problems and likely solutions. This mode helps more experienced users determine the causes of the printer should be checked at the same time. 6-2 If the self test does not work, contact your dealer to replace the head yourself because other parts of communication problems between the printer and the computer. This is...

User Manual - Page 115

.... Be sure that the printer is flickering, the LQ has stopped to allow the print head to re-start it to the single sheet position. Check the paper supply. l The ribbon may be jammed. Single sheets do anything to cool. l If the printer stops, the beeper sounds, and the ON LINE light does not flicker, turn...

User Manual - Page 207

... a time and a parallel interface transmits data one line space. Letter Quality (LQ) One of two methods of dots per character for high-speed printing. Line feed A control code or button that adjusts the loading and short tear-off positions in which the paper is italicized. Interface The connection between the computer and the printer...

Technical Manual - Page 31

... is detected). Abnormal Voltage Beeps 5 times, pausing every beep. RAM Error Beeps 6 to the above error sequence when any of the following states occurs. q A printhead drive transistor is not detected after every 4 beeps. q The printhead is moved outside of the printer. 1.8.1 Buzzer Operation The buzzer beeps as follows: 6 times Internal RAM (CPU) 8 times Lower Address RAM (IC...

Technical Manual - Page 33

REV.-A 1.10 PAPER END DETECTION The paper end is detected by lighting the lamp on the control panel and ringing the buzzer. ERROR signal: LOW After the paper end is detected, the printer indicates it by the PE sensor. Figure 1-10 shows the paper end detection position. Approx. 59. 9mm ABC XYZ I Fig. 1-10...

Technical Manual - Page 42

... Interface Control Circuit Block Diagram 2-34 Z.ii Control Circuit Block Diagram 2-12 Figure 2-10. Step-Down Timings 2. -18 Figure 2-16. AMP 1 Output 2. . -22 Figure 2-22.. +24V Regulator Circuit ...Rectifier and Smoothing Circuit 2-17 Figure 2-14. REV.-A 2.3.4.5 Printer Error Detection 2-39 2.3.5 Printer Mechanism Control 2-41 2.3.5.1 Carriage Control Circuit 2-41 2.3.5.2 ...

Technical Manual - Page 64

... 2-20 ,. When it exceeds the preset value, it lower than the preset voltage or current c k ", value, it is controlled by the error amplifier to keep it is controlled by the dead-time control voltage. Figure 2-17. o I I I vi ~ I I I / OFF ON OFF ON OFF ON OFF ON o - : @Terminol - - - - - : GTerrnind - . - REV.-A ~.., As shown in Figure...

Technical Manual - Page 83

... incorrect as follows: Beeps 6 times: internal CPU Beeps 8 times: ST-RAM (5A) Beeps 10 times: ST-RAM (6A) There are performed, and a check sum of the IC6A back-up SRAM is cut off so that detects various errors and informs the user of the type of errors, descriptions, and printer states are as follows: q Carriage Errors: The buzzer beeps 6 times, pausing briefly...

Technical Manual - Page 84

REV.-A q Paper End Error f- '.", The buzzer beeps 20 times with a pause after every four beeps. q PE LED lights q Buzzer beeps. 3.- *-": 2-40 When the paper-out state is detected, the printer is set OFF LINE, and the following process is performed: q PE signal goes high. q No paper was loaded when the printer power was detected during printing (paper feeding). " The...

Technical Manual - Page 130

... carriage motor mounting plate. 4. Attach the timing-belt tension spring to hooks on the carriage motor mounting plate. 4-17 Mount the carriage motor with carriage motor mounting plate and carriage motor mounting bushes on base frame by lightly tightening two CPS (0) (3 X 10) screws. 3. Set the timing belt correctly at the drive pulley of...

Technical Manual - Page 164

... (Perform Function. REV.-A FX-850/1050 PRINTER LOCATION IC4A DIAGNOSTICS ROM NOTE: Check does not require connection to see if the ONLINE LED light is on or off. (3) Check ... BLINKS (YES) q REPLACE IC5A (RAM ERROR) (NO) 1 PAPER OUT LED BLINKS (YES) q REPLACE IC6A (RAM ERROR) (NO) I READY LED BRINKS (YES) + REPLACE IC4B(RAM ERROR) (NO) I BUZZER BEEPS (NO) q REPLACE IC7A (YES) I...