Harbor Freight Tools 280 Support Question
Harbor Freight Tools 280 Support Question
Find answers below for this question about Harbor Freight Tools 280 - Straight Line Air Sander.Need a Harbor Freight Tools 280 manual? We have 1 online manual for this item!
Question posted by lopezaochoa on August 26th, 2015
Is There A Manual To Set The Time On A Straight Line Sander , Itook It A Part An
I after I put the sander back together it just doesent work right
Current Answers
Answer #1: Posted by TommyKervz on August 27th, 2015 3:21 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Please download and refer on the user manual for any possible options' Click the link below.
https://www.helpowl.com/manuals/Harbor%20Freight%20Tools/280/228974
Click here to request further assistance.
Related Harbor Freight Tools 280 Manual Pages
User Manual - Page 1
...rights reserved. Tools required for assembly and service may differ slightly from the product described herein. Failure to continuing improvements, actual product may not be reproduced in serious injury. Copyright© 1997 by Harbor Freight Tools... manual may be included. REV 14f
No portion of Harbor Freight Tools. 2-3/4″ X 17-1/2″ AIR INLINE SANDER
Model 00280
SET UP...
User Manual - Page 2
... SPECIFIC SAFETY INSTRUCTIONS 5
SYMBOL DEFINITIONS 5
FUNCTIONAL DESCRIPTION 8
SPECIFICATIONS 8 COMPONENTS AND CONTROLS 8
INITIAL TOOL SET UP/ASSEMBLY��8
UNPACKING 8 AIR SUPPLY 8
OPERATING INSTRUCTIONS 10
TOOL SET UP 10
INSTALLING SANDPAPER 10
WORK PIECE AND WORK AREA SET UP 11
GENERAL OPERATING INSTRUCTIONS 11
USER-MAINTENANCE INSTRUCTIONS 12
CLEANING, MAINTENANCE...
User Manual - Page 3
.... Do not use common sense when operating the tool. Obey all safety messages that follow this manual for future reference.
Keep the work area clean and well lighted. The tool is the safety alert symbol. Keep this manual, on the labeling, and all the instructions before using tools, basic precautions should always be followed, including the...
User Manual - Page 4
... on the switch or connect the
tool to the air supply with sharp cutting edges
f.
air source before connecting to control.
e. A tool is unstable
of drugs, alcohol, or medication. f.
goggles.
If damaged, have the tool serviced before leaving the work
better control of children and other condition that affects the tool's operation. Use clamps or another practical...
User Manual - Page 5
... concerning Risk of Respiratory Injury. b. Read and understand this tool with both hands only. Page 5
during use . Air source
CFM SCFM NPT
Cubic Feet per Minute flow
Cubic Feet per square inch of pressure
c. Always verify prior to persons. NPS
National pipe thread, straight
WARNING marking concerning Risk of Explosion. Such
1. Wear NIOSHapproved...
User Manual - Page 6
...air supply in an emergency, even if a hose is a choice.
7.
Let the tool
8.
To reduce vibration, maintain tool...tool as lightly as explained in a well ventilated area, and work . accessory may cause temporary or permanent physical injury,
6. Do not smoke during use with accessories rated to
3. this manual...and precautions discussed in -line shutoff valve to reduce ...
User Manual - Page 8
... at the beginning of this manual. Do not use of this manual including all text under subheadings therein before set up . Note: For additional... the item is ruptured.
Air Compressor
Quick Coupler
Regulator with pressure gauge, oiler, in-line shutoff valve, and quick ...Tools at 1-888-866-5797 as soon as possible.
• This air tool may cause the tool to power this plug before set...
User Manual - Page 9
... long enough to reach the work area with enough extra length to Operation section for leaks. The air hose must be closed quickly. Add a few drops of Pneumatic Tool Oil to the off position;
refer to allow the air tool to ensure that the air output is not used at any time. Note: If an automatic oiler...
User Manual - Page 10
...Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the Trigger before set up on the tension bar at each end of the Sander... beginning of this manual including all text under subheadings therein before performing any inspection, maintenance, or cleaning procedures. Inspect...
User Manual - Page 11
to the air compressor's hose. Work Piece and Work Area Set Up
1. The air hose must be hazardous objects (such as utility lines or foreign objects) nearby that is detected, disconnect the air hose and repair before making contact with the work surface in a smooth steady motion.
Make sure you are sanding. Connect the Sander to make sure the sandpaper...
User Manual - Page 12
... 12
For technical questions, please call 1-888-866-5797. Other lubricants may damage the mechanism and may be regularly drained.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use , wipe off the tool, detach the air supply, safely discharge any residual air pressure in this manual must be highly flammable, causing an explosion.
User Manual - Page 13
... is normal,
2.
especially on older
tools.)
3. If cross-threaded, disassemble and replace damaged parts before service. Disconnect air supply before use .
6. Not enough air pressure and/
or air flow. Do not exceed maximum air pressure.
2. Incorrect lubrication or not enough lubrication.
3. Install in-line filter in Initial Set Up: Air Supply.
1. Worn parts. Loose housing...
User Manual - Page 14
PARTS LIST
Part
Description
Qty Part
Description
Qty
1 Air Inlet
1
20 Flat Head Screw
4
2 Rear Head
1
21 Actuator Gear
1
3 Gasket
1
22 Actuator Valve
1
5 Socket Cap Screw
7
23 Shaft
1
6 Valve Spring
1
24 Plunger... PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
User Manual - Page 16
... or property, or for death, injuries to you must accompany the merchandise. This warranty gives you specific legal rights and you with transportation charges prepaid. Item 00280 Limited 90 Day Warranty
Harbor Freight Tools Co. To take advantage of purchase. We will either repair or replace the product at our expense, but...
Similar Questions
Timing The Gear Set On Central Pneumatic 91773 Air File
(Posted by mop1960 7 months ago)
How Do I Change The Turn Table Plates
how do I change turntable plate
how do I change turntable plate
(Posted by Chetmaniak 11 months ago)
The Cross Cut Is Not Straight
How do I square the blade is not straight, it's diagonal? Please and thank you
How do I square the blade is not straight, it's diagonal? Please and thank you
(Posted by bossroberto682 1 year ago)
Are Their Any Timing Marks For When You Disassemble It ?
(Posted by ronquest440mopar 1 year ago)
Laser Line And Cutting Line Do Not Line Up
(Posted by jeangambrell 9 years ago)