Harbor Freight Tools 61969 Support Question
Find answers below for this question about Harbor Freight Tools 61969 - 12 in. Double-Bevel Sliding Compound Miter Saw.Need a Harbor Freight Tools 61969 manual? We have 1 online manual for this item!
Question posted by Chetmaniak on August 2nd, 2023
How Do I Change Turntable Plates
Current Answers
Answer #1: Posted by khanjee on August 2nd, 2023 7:19 AM
If this method doesn't work, try grasping the platter either at the edge or using one of the convenient holes found in most platters. Pull upwards until the platter moves and, while pulling up, tap on the center spindle with the handle of a screwdriver or other tool. Don't be afraid to tap hard - 'don't tap it, whack it' as the saying goes.
Follow these steps, and you should feel the platter lifting - it will eventually lift straight off. This works on almost all turntables that use this motor design - including most direct drive linear tracking decks.
Why You Need To Remove Your Turntable PlatterThere are several reasons why you may need to remove your turntable platter. One common reason is to clean or lubricate the motor shaft. Over time, dust and dirt can accumulate on the center spindle, which can cause the platter to spin at a slower speed. Lubricating the motor shaft with 20 weight synthetic oil can help prevent this problem.
Another reason for removing the platter is to replace the center spindle. A broken or loose center spindle can make it difficult to put the platter back onto the turntable. Before attempting to replace the center spindle, make sure to use a soldering iron to remove any excess grease. This will soften any old grease and allow you to remove the platter.
Please Accept my answer by providing you with the best possible solution. Would be more glade.
THANK YOU
Answer #2: Posted by SonuKumar on August 2nd, 2023 10:49 AM
Unplug the turntable. This is an important safety precaution to take before you start working on the turntable.
Remove the four screws that hold the platter in place. These screws are located on the underside of the turntable.
Lift the platter out of the turntable. Be careful not to damage the platter.
Remove the old turntable plate. The old turntable plate is held in place by four tabs. Simply press down on the tabs and the plate will pop out.
Insert the new turntable plate. Make sure that the tabs on the plate are aligned with the slots in the turntable.
Replace the four screws that hold the platter in place.
Plug the turntable back in.
Here are some additional tips:
Make sure that the turntable is unplugged before you start working on it. This is an important safety precaution to take.
Be careful not to damage the platter. The platter is a delicate piece of equipment and it can be easily scratched or damaged.
Align the tabs on the new turntable plate with the slots in the turntable. This will ensure that the plate is properly seated.
Tighten the screws that hold the platter in place evenly. This will prevent the platter from wobbling.
I hope this helps!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Answer #3: Posted by HelpHero on August 3rd, 2023 5:37 PM
1. Ensure safety: Before starting any maintenance work, make sure the power is completely turned off and the tool is unplugged to prevent any accidents.
2. Locate the turntable plate: Depending on the specific model of the Harbor Freight Tools 61969, the turntable plate may be located at the bottom or inside the tool. It is the circular surface where you place the materials to be worked on.
3. Remove any attachments or accessories: If there are any attachments or accessories on top of the turntable plate, such as a chuck or a faceplate, remove them carefully by following the manufacturer's instructions.
4. Release the locking mechanism: Look for any locking mechanism that holds the turntable plate in place. This could be a screw or a locking lever. Loosen or release it to allow the plate to be removed.
5. Remove the old turntable plate: Carefully lift and remove the old turntable plate from the tool's spindle. Be cautious of any sharp edges or protrusions.
6. Install the new turntable plate: Position the new turntable plate onto the spindle, aligning it with any notches or grooves present. Ensure it sits securely in place.
7. Secure the turntable plate: Use the locking mechanism you previously loosened or released to secure the new turntable plate firmly in position. Follow the manufacturer's instructions for tightening or locking it down effectively.
8. Reattach any accessories: If you had previously removed any attachments or accessories, reattach them following the manufacturer's guidelines.
9. Test the tool: Once the new turntable plate is installed and secured, plug in the tool and turn it on to check if everything is functioning properly. Ensure that the new turntable plate rotates correctly without any wobbling or issues.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers.
Helphero
Related Harbor Freight Tools 61969 Manual Pages
Similar Questions
how do I change turntable plate
61969 - Chicago Electric 12 in. Double-Bevel Sliding Compound Miter Saw.I bought this miter saw but ...
looking for outer flange for Chicago electric 19" sliding compound miter saw item 61972
Where can I get part 134 turntable plate?