Home » Hayward » Pool & Spa » Hayward Max-Flo II

Hayward Max-Flo II Support Question

Find answers below for this question about Hayward Max-Flo II.
Need a Hayward Max-Flo II manual? We have 1 online manual for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by MC1869 on June 5th, 2012

3 Questions. from The Capacitor There Is A Red Wire And A Stpipred And

WHITE.WHERE DOES EACH ONE CONNECT. WHICH CONECTORS NARE USED FOR THE 115 VOLT SET UP. WHERE DOES THE CERAMIC SEAT GO ON SEAL INSTALLATION

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hayward Max-Flo II Manual Pages

All Max-Flo II models - Page 1

.... WARNING - This product should be installed and serviced only by a qualified professional. ATTENTION INSTALLER - HAYWARD POOL PRODUCTS 620 DIVISION STREET ELIZABETH, NJ 07207 (908) 351-5400 www.haywardpool.com www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Designed for pools of non-Hayward replacement parts voids warranty. The Max-Flo II is a series of high technology self...

All Max-Flo II models - Page 2

... - This pump is strongly advised to protect the electrical components from using them as the filtration system, pumps, and heaters must be installed and serviced only by a qualified professional. Select a well-drained area, one of injury, do not permit children to hazards. Max-Flo II ™ Series ____ ____ _____ _ Page 2 of actions that are...

All Max-Flo II models - Page 3

... supply to the electrician: Use a solid copper conductor, size 8 or larger. Also, contact a licensed electrician for information on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to all wiring standards including, but not limited to pool structure will increase risk for such seating areas. - Connect a No. 8 AWG (8.4 mm2) solid...

All Max-Flo II models - Page 4

...install according to pressure in the system, which may result in a position to allow the motor to the pool. Before starting the circulation system. All suction and discharge valves MUST be OPEN when starting system pump, fully open position. Strainer cover must be properly secured to seal with strainer cover lock ring. Max-Flo II... not operate pool and spa circulation system ...

All Max-Flo II models - Page 5

...Dimension "A" 1 12.0" 1.5 12.5" 2 13.0" Installation Instructions WARNING - Allow adequate access for outdoor use of piping (L as possible to protect the electrical... codes. Max-Flo II ™ Series__________ Product Specifications _____ Page 5 of air for cooling. Pump Mounting Install pump on...must equal or be as close to pool as practical and run suction lines as ...

All Max-Flo II models - Page 6

...motor before connecting to force hose connector fitting past this stop. Pool and spa fittings MUST conform to two layers of a swimming pool filtration system operate under pressure. Electrical WARNING - Use copper conductors only. Max-Flo II ™ Series __________ Pump Mounting (cont'd) _____ Page 6 of Plumbing and Mechanical Officials (IAPMO) standards. Incorrectly installed and/or...

All Max-Flo II models - Page 7

... available) on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to all wiring standards including, but not limited to verify they are sealed properly to prevent leaks. 3. Remove any trapped air in severe personal injury. use to removing cover. Immediately inspect all applicable local codes, regulations, and...

All Max-Flo II models - Page 8

...install on strainer housing; If leakage occurs DO NOT start pump. Insure air vents are opened. Do NOT use water to tighten cover. Replace with compressed air. See "Shaft Seal Change Instructions" in your pool/spa...self-priming using 1 ½" pipe. Hayward pumps have self-lubricating motor bearings and shaft seals. Use only a low pressure (below ). Max-Flo II ™...

All Max-Flo II models - Page 9

... instructions may result in serious personal injury or death. 1. Disconnect pump from the motor. 4. If tight, use this product. Seal Installation (See Parts Diagram on page 11 of this manual for pump component locations.) 8. Removing the Ceramic Seat (See Parts Diagram on page 11 of this manual for pump component locations.) 6. Slide the motor assembly...

All Max-Flo II models - Page 10

... impeller (item#10) onto the seal plate (item#13), aligning the ...using the two (2) hex shaped screws. Re-attach motor end cover/canopy by holding motor shaft with a clean, soft, cotton cloth. 11. Diagram 1 www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Gently wipe the black, polished surface of this page. Max-Flo II ™ Series Page 10 of the ceramic seat...

All Max-Flo II models - Page 11

Max-Flo II ™ Series Replacement Parts Parts Diagram Page 11 of 16 Item #16: Optional with some models SEE PARTS LISTING ON NEXT PAGE www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

All Max-Flo II models - Page 12

Max-Flo II... Hardware Pack (Includes 4 Housing Bolts, Seal- 10 Plate Spacers and Square Nuts 7...115/230V) SPX2707Z2M Motor, 1 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V) SPX2710Z2M Motor, 1-1/2 HP, Two Speed, Threaded Shaft 1 (Single Phase, 60 Cycle 115/230V) SPX2715Z2M Motor, 2 HP, Two Speed, Threaded Shaft (Single 1 Phase, 60 Cycle 115/230V) www.haywardpool.com USE...

All Max-Flo II models - Page 13

... seated in this with the wiring diagram on pool ...seal. 2. Any self-priming pump will automatically shut off to determine if pump will continue to ensure that the wiring... www.haywardpool.com USE ONLY HAYWARD GENUINE REPLACEMENT...wired for line blockage. Re-check strainer housing cover and all threaded connections for blocked suction line or dirty strainer basket. Max-Flo II...

All Max-Flo II models - Page 14

...Pool Products, 2005 All rights reserved. Vibration due to the equipment pad. 3. Undersized pool piping. Loose stones/debris hitting impeller could be replaced at any joint, low water level in a smaller eyeball fitting. 2. Max-Flo II...4. Solution: Re-tighten using Teflon tape. 5. Plugged, restricted, or damaged impeller. Solution: Replace including new seal assembly. Noisy Pump - ...

All Max-Flo II models - Page 15

... freezing, negligence, improper installation, use or care, or as a result of purchase/installation. The Hayward Pool Products warranty does not apply to : Hayward Pool Products, 620 Division Street... shipment from our plant. This warranty gives you specific legal rights, and you . Max-Flo II ™ Series ___ Page 15 of purchase. All other such costs incurred in service...

All Max-Flo II models - Page 16