Hayward VR1000 Support Question
Hayward VR1000 Support Question
Find answers below for this question about Hayward VR1000.Need a Hayward VR1000 manual? We have 2 online manuals for this item!
Question posted by meadowlawnmaint on May 7th, 2015
I Don't Think The Vr 1000 Is Working Right
Are pump went out and i replaced it and now the pump comes on when I turn the breaker on
Current Answers
Related Hayward VR1000 Manual Pages
Model: All Models - Owners Manual - Page 2
... pool, spa, or hot tub. All electrical wiring MUST be in a building such that will increase risk for bonding requirements. To reduce the risk of the components. Before working on pump or motor, turn... one that it cannot be caught in evisceration (disembowelment). Risk of electric shock replace damaged wiring immediately. WARNING To reduce the risk of Electric Shock.
To reduce the...
Model: All Models - Owners Manual - Page 3
...outlets shall be inspected frequently and replaced at more suction outlets per pump installed in accordance with strainer cover lock ring. o Never use the Pool or Spa if any suction outlet component ... distances to do so could result in violent separation of 16
STRATUM™ Model VR1000
P/N: ISVR1000 Rev: M
WARNING - Hazardous Pressure. Before starting the circulation system.
...
Model: All Models - Owners Manual - Page 7
...CUSTOM ACTION IS REQUIRED. This is monitoring the pool, but the screen has been turned off the alarm. The system should restart. ...REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN
Tel: 908.351.5400 www.haywardpool.com The system should restart. Under Vacuum Window indicates a problem with the Pump...pool/spa. Pushing the "Menu" button will go to confirm the VR1000 is first powered up .
Model: All Models - Owners Manual - Page 9
... system has turned off until normal voltage is providing protection for proper operation. When this time a High Vacuum setting provides protection. The system is still in the operation.)
VACUUM ANOMALY DETECTED
The pump(s) and the vacuum solenoid valve are compared to verify that the pump is functioning properly. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
Model: All Models - Owners Manual - Page 11
... ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN
Tel: 908.351.5400 www.haywardpool.com Incorrectly installed and/or improperly tested filtration equipment and/or components may cause cracking of swimming pool, spa, or hot tub. TO AVOID DANGEROUS OR FATAL ELECTRICAL SHOCK, TURN OFF POWER
TO MOTOR BEFORE WORKING ON ELECTRICAL...
Model: All Models - Owners Manual - Page 12
... add chemicals to pool/spa system directly in conformance with "Jack's 327" each time it is removed. Adding undiluted
chemicals may damage seals, causing leakage, flooding, and voids
warranty. CLOSE VALVES in circuit; Release all pressure from pump and piping system using filter manual air relief valve. See filter owner's manual. turn clockwise to...
Model: All Models - Owners Manual - Page 13
... pool/spa
system.
Drain water level below ). WARNING - The STRATUM™ only provides a layer of flow from the suction outlet (Main Drain) to the skimmer will not damage plastic system components; Do NOT strike basket to indicate the unit is , changing the pattern of protection against Body Suction Entrapment. ATTENTION -
Disconnect pump from VR1000...
Model: All Models - Owners Manual - Page 14
...other rights, which vary from the date of purchase.
To original purchasers of this equipment, Hayward Pool Products warrants its products free from defects in obtaining warranty replacements.
Vacuum...manufacturer will apply.
This warranty gives you specific legal rights, and you . Page 14 of 16
STRATUM™ Model VR1000
P/N: ISVR1000 Rev: M
HAYWARD® LIMITED WARRANTY
...
Model: All Models - Owners Manual - Page 15
...REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN
Tel: 908.351.5400 www.haywardpool.com
STRATUM™ Model VR1000
PRODUCT REGISTRATION
(Retain For Your Records)
P/N: ISVR1000 Rev: M
DATE OF INSTALLATION
INITIAL PRESSURE GAUGE READING (CLEAN FILTER
PUMP MODEL HORSEPOWER
FILTER MODEL SERIAL NUMBER
MODEL VR1000...© Hayward Pool Products 2007 All rights reserved. Please ...
Model: All Models - Service/Installation - Page 2
... a cord with storable pools. Notes to the pump.
- WARNING - A negative pressure applied directly to the intestines through an unprotected suction outlet sump or suction outlet cover which are, damaged, broken, cracked, missing, or unsecured can result in or on pump or motor, turn power supply OFF. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons...
Model: All Models - Service/Installation - Page 3
...injury, or death.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN.... DEFINITIONS:
Suction Outlet - o Never use the Pool or Spa if any listed (per pump installed in accordance with the covers. o In addition...be OPEN when starting system pump, fully open position.
WARNING - Inches of 24
STRATUM™ Model VR1000
P/N: ISVR1000TECH Rev: J
...
Model: All Models - Service/Installation - Page 5
... the pump. Locate a straight section of the Pool/Spa system. Holding the
tubing in package.) 4. Saddle Gasket CL220C (Supplied in package.) 5. The VR1000 is ...TURN OFF THE ELECTRICAL POWER AT THE CIRCUIT BREAKER. 2. Remove all check valves from the circulation systems. The presence of a check valve used on a single pump or a combination of a single pump with a booster pump...
Model: All Models - Service/Installation - Page 6
... pool bonding system by an 8AWG (6AWG for flooded suction. 9. Replace ...pool turn the power off, and move the switch as shown in motor relay position 3. Leave the switch in series with two screws included. 12. Dip Switch 8 performs special functions related to ON. 7. Page 6 of a pinched vacuum tube. For 2 Speed pumps, set Dip Switch 4 to the detection of 24
STRATUM™ Model VR1000...
Model: All Models - Service/Installation - Page 8
... Flooded Suction and Pumps installed more than 3' above and stop "Unprotected" mode before Appling power to the STRATUM™ (See Page 19)
VR1000 VER X.X Initial Start OK
INITIAL SCREENS: These will allow Swimmers and Bathers in the pool and spa when the STRATUM™ is in Pool or Spa?
No Swimmers Allow In pool/Spa
Is Anyone in...
Model: All Models - Service/Installation - Page 10
...set. Page 10 of 24
STRATUM™ Model VR1000
P/N: ISVR1000TECH Rev: J
CUSTOMER ACCESSIBLE MODES
To...on a daily basis. Follow the above for the Booster Pump. For "OVERNIGHT" operation, set timer follow
screen instructions...." or "each day mode is actively protecting the pool/spa. "Down" will move On time earlier "UP"...REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN Tel: 908....
Model: All Models - Service/Installation - Page 12
...of 24
STRATUM™ Model VR1000
P/N: ISVR1000TECH Rev: J
...pump motor can
cause serious or fatal electrical shock hazard. USE ONLY HAYWARD GENUINE REPLACEMENT...Use the load circuit breaker as the Master ...pump operation. If other lights or appliances are also on the motor housing and to all metal parts of swimming pool, spa...TURN OFF POWER TO
MOTOR BEFORE WORKING ON ELECTRICAL CONNECTIONS. Pump...
Model: All Models - Service/Installation - Page 13
...pump to prime, which may damage seals, causing leakage, flooding, and
voids warranty. turn clockwise to pool/spa system directly in the system by hand only (no more detail.
Page 13 of 24
STRATUM™ Model VR1000... been released before re-starting motor. Replace strainer cover on strainer cover. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville...
Model: All Models - Service/Installation - Page 14
...the plumbing has been complete, and the "High Vacuum" for a "Flooded Suction" pump. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, NC Nashville, TN Tel: 908.351.5400 www.haywardpool....determine if the system is running properly.
Please see page 18 for pool/spa applications with all the configurations of the VR1000 should only be set up to the next screen press "MENU"/"...
Model: All Models - Service/Installation - Page 19
...
The default value of 24
STRATUM™ Model VR1000
P/N: ISVR1000TECH Rev: J
FOR FLOODED SUCTION AND PUMPS INSTALLED MORE THAN 3' ABOVE THE SURFACE OF THE POOL. Weld Relay ADC = 60 CHANGE? Note: The setting is not exact and additional lift at the breaker.
Turn dip switch No. 7 to 2 seconds. VR1000 VER X.X Initial Start OK
Initial Set-up...
Model: All Models - Service/Installation - Page 21
...Pool Tech Mode procedures. Lo vacuum (window), 2 parms in 16 bit ADC units - Sensor/Solenoid failure (periodic test)
Run - Pumps... will run a test similar to see if it IS installed. Rate of 24
STRATUM™ Model VR1000...readings.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pomona, CA Clemmons, ...Yes & No key press while pumps were turned off loop
Stabilization - periodic SS ...
Similar Questions
Brand New Hayward Dv5000 Now Working Right Out Of The Box. Need Info On Probable
cause and solution to proble
cause and solution to proble
(Posted by tnt1947 5 years ago)
No Deplay On Panel Did Get Pool To Run Not Sure If The System Is Working Right
(Posted by nheimbach 11 years ago)
It Has Just Stopped Working After Four Years Of Excellent Service.
Where can I send it for repair? The power box is working. The unit itself is not. Is there an inte...
Where can I send it for repair? The power box is working. The unit itself is not. Is there an inte...
(Posted by Basur107 11 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)
Intermittent Starting Of Super Ii Pool Motor
Have a Hayward Super II 1.0 HP pool motor about 15 yars old. Sometimes it does not start - it will h...
Have a Hayward Super II 1.0 HP pool motor about 15 yars old. Sometimes it does not start - it will h...
(Posted by cmathe 12 years ago)