Hunter 90064 Support Question
Hunter 90064 Support Question
Find answers below for this question about Hunter 90064.Need a Hunter 90064 manual? We have 1 online manual for this item!
Question posted by alcaustinc on July 30th, 2018
Replacement Parts Order
I need to replace the glass cover piece Where can I order
Current Answers
Answer #1: Posted by waelsaidani1 on July 31st, 2018 2:06 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
You can this replacement part here: http://www.spareparts.plus/Household/Heating_and_AC/Hunter/90064/spareparts/
Related Hunter 90064 Manual Pages
Owner's Manual - Page 1
Owner's Manual
Model
90063/90064
1
41722-01 09/09/2011 Ellipse
Bath Ventilator with Light and Night Light
English
Español
Página 21
41722-01 20110909 ©2011 Hunter Fan Co.
Owner's Manual - Page 2
...detergent, such as listed below. METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER. MAINTENANCE
The ...needed for proper combustion and exhausting of gasses through the flue (chimney) of fuel burning equipment to tab) and twist screwdriver. Install fan... the motor bearings are making excessive or unusual noises, replace the motor with all applicable codes and standards, including fire...
Owner's Manual - Page 3
...-01 09/09/2011
Loosen screws. Not Included.
Before Installation
1
30
20
O FF
O FF
Tools Needed. (Not supplied) Estimated assembly time: 30 to 60 minutes
NOTE: Remove all the parts. If damaged, call 1-888-830-1326 for replacements. Check all packing materials before installation.
2
I 74508-03-133 J 77520-01 K 65219 L 95740-01/02...
Owner's Manual - Page 4
3
4
H
E
Remove the motor/blower from the housing.
5
Remove packing material.
6
Remove the pre-loaded screw tip covers.
7 G
Back out the pre-loaded screw tips until flush with the side of the housing.
8
F
Remove the wiring cover screw.
4
41722-01 09/09/2011
Remove the wiring cover.
Owner's Manual - Page 5
... only from above go to step D11, page15
New Construction - Screw pre-loaded screws into the housing and secure with the washer. Use second if needed.
Owner's Manual - Page 6
...Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In...connections are inside the box or under
the wiring cover plate.
6
41722-01 09/09/2011
Tighten the wiring cover plate screw. A15
F A16
2
1
F
G•
Install the wiring cover plate.
A13
Pull wires through the strain relief....
Owner's Manual - Page 7
...the motor by inserting the tabs and pushing up into position.
A017
A18
H
Connect 4" duct and vent to the wiring cover plate. If the motor does not run, check the plug connection.
7
41722-01 09/09/2011 A20
H
I
...and the housing. If ducting does not fit securely, an adapter may need
to be purchased. A21
A22
ON
OFF
Turn on the power source. Test the motor. Tape joints.
Owner's Manual - Page 9
... Night Light
Light
Black 2 Pin
White
White Red Night Light 3 Pin Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown.
9
...
Owner's Manual - Page 10
...fit securely, an adapter may need
to the outside.
Make sure the wires are inside the box or under
the wiring cover plate.
B22
B21
G•
Tighten the wiring cover plate screw.
B23
H
Connect... to be purchased. B24
Connect wiring from the motor to the wiring cover plate. B20
F
2
1
F
Install the wiring cover plate. Make sure all wiring connections are not pinched between the motor ...
Owner's Manual - Page 11
... the motor does not run, check the plug connection. Use the motor housing as a template to attach grille. Existing Construction - accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to make sure the opening is large enough to accommodate the new
motor housing (9"x 9.75").
Owner's Manual - Page 13
C21
Pull wires through the strain relief. C20
Connect 4" duct and vent to be purchased.
Tighten the strain relief screws.
13
41722-01 09/09/2011 C17
C18
Attach the rails onto the screws. Tape joints.
If ducting does not fit securely, an adapter may need to the outside.
C19
Tighten screws.
Owner's Manual - Page 14
... the tabs and pushing up into
position.
C26
H H
Connect wiring from the motor to the wiring cover plate.
C22
Fan Motor Night Light
Light
Black 2 Pin
White
3 Pin
White Red Night Light
Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC...
Owner's Manual - Page 15
accessible only from below
D11 EXISTING FAN
D12
E
Remove an existing fan and check to make sure the opening is large enough to attach grille.
If the motor does not run, check the plug connection. Turn on ...
Owner's Manual - Page 16
... Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Red Switch 1 (AC In) Black Switch 2 (AC In)
Connect wires as shown.
16
41722-01 09/09/2011 D15
D14
2 1
Attach existing ducting to be purchased. Tape joints. If ducting does not fit securely,
an adapter may need...
Owner's Manual - Page 17
.... Make sure the wires are inside the box or under
the wiring cover plate. D19
D18
G•
Tighten the wiring cover plate screw.
D21
H
Reinstall the motor by tightening the 2 screws.
17
41722-01 09/... connections are not pinched between the
motor and the housing. D17
2
1
F
Install the wiring cover plate.
D22
I
Secure the motor by inserting the tabs and pushing up into position.
Owner's Manual - Page 18
...
ON
OFF
Test the motor.
DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. Attaching the Grille
E1
H M
Remove the thumbscrews.
E2
N
Remove glass. E3
E4
H
J L
Connect wiring harness.
If the motor does not run, check the plug connection. Position the strain relief bracket between the plugs as shown...
Owner's Manual - Page 19
If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://...movement. • T urn power on . Problem: Light does not come on , replace fuse, or reset breaker. • Check all fasteners.
• C heck the glass to make sure it is noisy.
Problem: Fan is secure. • C heck the flapper to make sure it matches the wiring ...
Owner's Manual - Page 20
... purchase price of your bath exhaust fan or provide a replacement free of charge. Proof of purchase is not purchased and installed in the U.S.A.
If no replacement part can be responsible for all insurance ...original user or consumer purchaser of this Hunter bath exhaust fan:
If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within five...
Similar Questions
I Need A Replacement Glass For Cover On This Item. How Can I Buy It?
I need replacement glass for this item
I need replacement glass for this item
(Posted by pwhitwam 6 years ago)
Replacement Glass For Hunter 90064
where can I purchase the replacement glad for the Hunter 90064 Exhaust Fan Light unit
where can I purchase the replacement glad for the Hunter 90064 Exhaust Fan Light unit
(Posted by Jwaller0717 7 years ago)
Why Am I Unable To Remove Glass Cover To Replace Bulbs?
Have been trying to remove the glass cover on my Hunter 82023 to replace bulbs for some time now. Fi...
Have been trying to remove the glass cover on my Hunter 82023 to replace bulbs for some time now. Fi...
(Posted by maroney914 8 years ago)
Hunter 90064 Bent Alabaster Glass Bathroom Fan.
Had purchased the above fan and the while trying to remove the glass to clean, it fell and the glass...
Had purchased the above fan and the while trying to remove the glass to clean, it fell and the glass...
(Posted by LindaGBGR 10 years ago)
Replacement Glass Globe
Are there replacement glass light globes available for this fan?
Are there replacement glass light globes available for this fan?
(Posted by vstofer 11 years ago)