LiftMaster CSW200UL Support Question
LiftMaster CSW200UL Support Question
Find answers below for this question about LiftMaster CSW200UL.Need a LiftMaster CSW200UL manual? We have 2 online manuals for this item!
Question posted by Anonymous-173407 on January 10th, 2023
Strike Open Light Is On And Magnet Doesn't Work To Hold Gate Close
Strike Open Light Is On And Magnet Doesn't Work To Hold Gate Close, What Is The Problem?
Current Answers
Answer #1: Posted by Odin on January 10th, 2023 6:22 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
Your question is not entirely clear, but review the troubleshooting tips starting at https://www.manualslib.com/manual/413903/Chamberlain-Csw200ul.html?page=45#manual.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Answer #2: Posted by SonuKumar on January 10th, 2023 8:47 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,651,140
Member since:
May 9th, 2021 Points: 16,651,140
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Answer #3: Posted by kane1234567 on January 11th, 2023 3:25 AM
kane1234567
Member since:
January 7th, 2023 Points: 700
Member since:
January 7th, 2023 Points: 700
There could be several reasons why the strike open light is on and the magnet isn't working to hold the gate closed. Here are a few possibilities:
- The power supply to the magnet is not functioning properly. This could be due to a problem with the wiring or a faulty power supply.
- The magnet itself may be damaged or malfunctioning. This could be caused by a manufacturing defect or due to wear and tear over time.
- The strike plate on the gate may be misaligned or damaged, preventing the magnet from making proper contact.
- There may be an issue with the electronic control board or the software that controls the strike and magnet.
- The gate or door that this lock is installed might be damaged or misaligned.
It is best to have a professional check and diagnose the problem, since it can be difficult to determine the cause without proper testing and inspection.
Related LiftMaster CSW200UL Manual Pages
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 3
...(Edge Sensors 25 Entrapment Protection Devices (Non-Contact Sensors 26
adjustments
Set Gate Opening Direction 27 Limit Switch Adjustments 28 Clutch Adjustment 28 Radio Receiver Programming 29-... Layout 11 Compact Installation Layout 12 Uphill Driveway Post Mounting Plate Installation 13 Gate Arm Installation 14 Output Shaft Adjustment 14 Control Board Description 15 Surge Suppressor ...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 5
...garage, retail store or other building servicing the general public. Commercial/General access vehicular gate operator
A vehicular gate...open and close directions of gate travel. UL325 ENTRAPMENT PROTECTION REQUIREMENTS
This chart illustrates the entrapment protection requirements for use in vehicular swing gate applications:
Class I - UL 3 2 5 M O D E L CL A SS I F I C A T I O N S
The CSW200UL...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 6
... of the gate operator.
8. b. c. The pedestrian access opening and closing to reduce the risk of the reset control shall not cause the operator to operate the controls. R eference owner's manual regarding placement of non-contact sensor for an individual application.
2. Gate operating system designers, installers and users must be properly installed and work freely in...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 7
... edged protrusions not exceeding 0.50 inches (12.7 mm) when other fixed object when the gate moves toward the fully open and fully closed positions. Specific Applications
2. Any non-automated gate that is required to perform their intended function.
3.1. All gates shall be designed, guarded or screened to the provisions in effect at 610-832-9585...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 8
... as posts or walls. • A swinging gate shall NOT open when vehicles are required when using a center loop. Suggested for vehicles 14 feet or longer.
Non-Contact Sensors (Photoelectric Sensors)
Install photoelectric sensors to protect against any entrapment or safety conditions encountered in BOTH the open and close gate cycles. • Locate entrapment protection devices...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 9
... I O N S
To prevent SERIOUS INJURY or DEATH from a moving gate: • Entrapment protection devices MUST be installed. Suggested for close cycle.
Safety loops are obstructing the gate path. Safety loops allows the gate to protect in your gate application. Edge sensor for open and close gate cycles. • Locate entrapment protection devices to protect against any entrapment...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 10
... gate and RIGID objects, such as posts.
• A swinging gate shall NOT open and close gate cycles.
• Locate entrapment protection devices to hang or ride on BOTH sides of a moving gate....gate operating device near a moving gate! Property owners MUST never allow anyone who may come near the gate's path! SAFETY PRECAUTIONS
THE CSW200UL™ IS FOR USE ON VEHICULAR PASSAGE GATES...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 13
B) Tack weld bracket in Open Position
9" Minimum 10" for Gate Clearance
8" Minimum to scissor when open gate and bend tape until tape is 90° from gate. C) Close gate, place tape measure between bracket and output shaft, open .
Note: Longer gates or retro-fits may require both arms to next page.)
For technical support: 1-800-528-2806 11 D) With tape...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 14
... to protect against the entrapment that could occur with this type of installation. (See entrapment protection devices.)
Outside Property Inside Property
Gate Open
26.5"
20" Minimum Width
Outside Property Inside Property
Gate Closed
33"
Hinge Center
2" 9"
23" 25.5"
20" to 32"
Cut
Long Arm
Cut
10"
22"
4"
36"
Cut
Short Arm
4"
20"
24"
Follow...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 16
... it does, go back and tighten the nut.
5 Replace cover and star knob. 14
Gate Closed
Weld the bracket on TOP of bracket. NO slippage should occur. Gate Open
Correct Installation
Once the gate arm measurements are calculated: Arm is on the gate.
Completely weld around the rectangular tubes and bracket!
........then weld the shorter arm...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 17
Timer - Radio Receiver LED - Strike Open LED - Exit Loop LED - Successful command executed. Gate hit obstruction when ON. Strike connected device activated when ON. Reverse Sensor - System ...Operator power OK when ON. Close, Stop, Open commands. Center Loop LED - Safety Loop LED - Alarm Sensor - Gate Opening Direction Selector -
Gate Locked LED - Operator power...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 18
... or any Key Switch
Dry Contact Remote NOT Included
315 MHz Factory Installed Radio Receiver Card Reader
Separate power for TES. All other terminals will Open and Close with a single push of a button.
16
Separate power for card reader. Push Button
Dry Contact
Telephone Entry System
12Vdc Failsafe Photoelectric Sensor
NOTE: Terminals...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 23
... Mode Auto Mode
110Vac Power Failure
Push and Hold to page 29 and 30 for programming radio receiver.
21
Note: All devices wired to the DC2000™ MUST be controlled by separate devices wired to operate gate. Example: If the DC2000 is restored. Gate automatically opens.
110Vac Power On, OmniControl™ Board Malfunction
Turn...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 24
...button again and HOLD to Close. Com
N.O.
STRIKE OPEN
RADIO RECEIVER
GATE LOCKED
EXIT LOOP
SAFETY LOOP
CENTER LOOP
RESET MOTOR
CLOSE STOP OPEN
POWER OVERLOAD
MADE IN USA
1234567
+12Vdc Ground
DC-BACKUP
POWER OVERLOAD
OmniControl™ Board Sensor Connection
12Vdc Failsafe Photoelectric
Sensor
Failsafe Photoelectric Sensor: If a photoelectric sensor is not working, loses power or...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 28
The gate will remain open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate:
• Locate entrapment protection devices to protect in BOTH the open until...photoelectric sensor is not working or loses power or photoelectric sensor is closing, it will stop and reopen. To prevent SERIOUS INJURY or DEATH from a moving gate and RIGID objects, ...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 31
... the risk of any combination of a moving gate: • ALWAYS keep gate in the (M) momentary position, the contacts will stay closed . P4 P2
Changing security from a moving gate. To verify, refer to the label next to jumper P4. (See illustration below.) The Receiver can be set to open or close for 1/4 second regardless of the length...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 32
...Operation is pressed.
Repeat Steps 1 and 2 for 30 seconds.
2. Within 30 seconds, press and hold the "Learn " button on the remote control is subject to use. Optional 315 MHz Hand Held Remotes...codes are prohibited, except for changing the code setting or replacing the battery. The learn indicator light will be used. NOTICE: To comply with FCC Standards FOR HOME OR OFFICE USE. NOTE:...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 40
...Closed (No Wire) Motor Black Limit Switch Brown Com Motor Green Purple Com Blue N.O. Dry - - - 24Vdc 0Vdc 5 or 0Vdc 0V 5 or 0Vdc 0Vdc 0Vdc 2 to 10Vdc 2 to 10Vdc 2 to 10Vdc 2 to 10Vdc 2 to 10Vdc 2 to 10Vdc
Master/Second Link Input
Radio Receiver, Strike Open... 5 or 0Vdc - Key Switch (8)
In
J2
3
Strike Open Push Button (9)
In
J2
4
Strike Open Push Button (10)
In
J2
5
Radio Receiver -...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 42
Reset Switch Red
-
Motor White Normally Closed (No Wire) Motor Black Limit Switch Brown Com Motor Green Purple Com Blue N.O. ... Inputs
External Loop Detector Center, Safety,
Exit Wires Input
40
NOTE: See diagram on previous page. Key Switch (8) Strike Open Push Button (9) Strike Open Push Button (10) Radio Receiver - (11) Radio Receiver (12) Radio Receiver + (13) Center External Loop ...
CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 46
...1. There is a problem. Audio Alarm ON
1. Gate has encountered two consecutive obstructions while trying to close or open .
It does not represent necessarily that there is a command holding the gate open .
For technical support... 3. Set a different working frequency. 4. Decrease the sensitivity of the loop detector. OR
2. One limit switch is a command hold active.
Any Loop LED ...
Similar Questions
Gate Opens From The Motor But Will Not Close From The Motor Or The Remotes.
(Posted by kdmcfall 4 years ago)
'strike Open' Light Liftmaster Sl3000ul
Why does the "Strike Open" Light stay on LiftMaster SL3000UL?
Why does the "Strike Open" Light stay on LiftMaster SL3000UL?
(Posted by markmanry 7 years ago)
Gates Remain Open
Gates will not close on command. "Strike Open" LED is lit and "Timer" and "Command Processed" LEDs a...
Gates will not close on command. "Strike Open" LED is lit and "Timer" and "Command Processed" LEDs a...
(Posted by eb1aa 8 years ago)
Garage Door Opener Light
We just purchased our house and the light was out in the door opener. When we replaced the bulb the ...
We just purchased our house and the light was out in the door opener. When we replaced the bulb the ...
(Posted by smokiesgirl 12 years ago)