Pyle PLUTV44CH Support Question
Pyle PLUTV44CH Support Question
Find answers below for this question about Pyle PLUTV44CH.Need a Pyle PLUTV44CH manual? We have 1 online manual for this item!
Question posted by Mannyny787 on June 27th, 2023
1500 Watt Amp Marine Plutv44ch
2 of the channels not working checked the wiring its good same color. I put it on another cable and the speaker worked i dont know if those channels are no good or what. Thank you
Current Answers
Answer #1: Posted by SonuKumar on June 27th, 2023 10:31 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,653,150
Member since:
May 9th, 2021 Points: 16,653,150
If you have verified that the wiring is correct and the same color, but two channels on the Pyle PLUTV44CH are not working while the speaker functions on another cable, it's possible that those specific channels on the amplifier may be faulty. Here are a few steps you can take to further troubleshoot the issue:
- Check speaker connections: Ensure that the speakers are properly connected to the amplifier. Confirm that the positive (+) and negative (-) terminals of the speaker match the corresponding terminals on the amplifier for the non-working channels.
- Swap speaker connections: Try swapping the speaker connections between the working and non-working channels. If the problem persists and the same channels remain inactive, it suggests that the issue is likely with the amplifier itself.
- Balance and fade settings: Check the balance and fade settings on the amplifier. It's possible that the settings are misconfigured, causing certain channels to be muted or attenuated. Ensure that the balance and fade controls are centered or adjusted appropriately to allow sound to be output to all channels.
- Reset the amplifier: Some amplifiers have a reset function that can be accessed through the menu settings or by holding down specific buttons. Consult the user manual for the Pyle PLUTV44CH to determine if there is a reset option available, and try performing a reset to see if it resolves the issue.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Pyle PLUTV44CH Manual Pages
Instruction Manual - Page 1
PLUTV44CH
1500W Waterproof Marine Speakers + 4 Ch. Rated Amplifier
PowerSport Amp for ATV, UTV, 4x4, Jeep, Wired RCA, AUX, and MP3 Audio Input Cable, for Boat Stereo Speaker & Other Watercraft
Instruction Manual - Page 2
... still hear normal traffic sounds in a reasonable distance.
This wire should be subject to high temperatures, such as from direct sunlight or hot air
from the car radio. • This power amplifier employs a protection circuit to protect the transistors and
speakers if the amplifier malfunctions.Do not attempt to test the protection circuits by...
Instruction Manual - Page 3
... wire lead to the same ground point. If the car stereo does not provide an "Auto-Antenna" lead, the remote turn the radio on so that the cable diameter is switched on terminal (REM). This will also switch off automatically - Do not ground any other amplifiers, to this application. Now turn the amplifier on period, the amplifier...
Instruction Manual - Page 4
... to the automatic antenna connector of your vehicle/or boat radio, the amplifier automatically switches ON and OFF. The lead cable's diameter should be at least 4 mm' for a length of 3 m and 6 mm" for a length of 0.5mm2 is sufficient. SPEAKERS CONNECTIONS
4 www.PyleUSA.com
POWER CONNECTION LEADS
REM (ON/OFF) REMOTE CONTROL...
Instruction Manual - Page 5
... to be connected to the car battery. • During a...color is equipped with a Power Antenna control wire, it can still splice into it. If only mono signal is available, a "Y" adapter is overheated. • the speaker...REPLACEMENT If the fuse blows, check the power connection and replace...wire is the same as possible to the +12V and GND terminals of a higher amperage fuse may cause amplifier...
Instruction Manual - Page 6
... (piping), ignition (cracking) or other car cable. The REM cable to look for the wiring between "low level in" of the amplifier and RCA or DIN output of the radio. • Lay the signal, speaker and power cables separately with the serial cables. Otherwise you use thicker ground cables or add further ground cables to interference; Poor Sound Quality (Distortions...
Instruction Manual - Page 7
... contact resistance. • Should all these meaures be without any success, the use multi core cable ends, spade terminals or others. PLUTV44CH Speaker Installation Speaker Mounting suggestion as below:
Auto Reconnection: Step 1: Unbolting the mounting bracket. Step 2: Slide in... To reduce contact resistance and bad and loose contacts, please solder the cable ends or use of the
speaker.
Instruction Manual - Page 8
Step 5: Use Butt Connector accessories to Connect Speaker wires (See Illustration 1,2,3).
1
2
3
Features: • Waterproof Rated Speakers • Pro Audio Power Sports Amplifier System Kit • 4-Channel Marine Audio Amplifier • Marine Grade Rugged Construction • Waterproof Rated & Weather-Resistant Connectors • Integrated Power Wiring Harness • Perfect for Custom...
Instruction Manual - Page 9
... is known in the Box: • (4) 4'' -inch Marine Speakers • Compact 4 Channel Marine Amp • (4) 2 Meters Speaker Wire • Audio Connection Cable, 3.5mm • Owner's Manual • Warranty Card • (4) 150x19x6mm (LxWxH) EVA Pads • (4) 165x19x2mm (LxWxH) EVA Pads • (8) Butt Connector
(Red Color For A.W.G 16-22)
Technical Specs: • Amplifier Type: 4-Ch.
Similar Questions
Can I Use My Blue Tooth Amp Without The Blue Tooth Connection
I would like to use my Pyle amp arroyo bluetooth is it possible
I would like to use my Pyle amp arroyo bluetooth is it possible
(Posted by fet2153 9 months ago)
On My Plutv44ch Am The Rca Jacks In The Manual Says Output Only. Is That True.
On my plutv44ch am the rca jacks in the manual says output only. Is that true. If so, how do I hook ...
On my plutv44ch am the rca jacks in the manual says output only. Is that true. If so, how do I hook ...
(Posted by davegray04 9 months ago)
Marine Amp
Hooked up my new 2 channel marine Amp and I get nothing when trying to play the radio . The booth to...
Hooked up my new 2 channel marine Amp and I get nothing when trying to play the radio . The booth to...
(Posted by jamesstambaugh58 10 months ago)
Maximum Output
How can i hook my PLA-2378 2000 watt amps up to get maximum output and bass so the amps wont cut out...
How can i hook my PLA-2378 2000 watt amps up to get maximum output and bass so the amps wont cut out...
(Posted by bensonb 11 years ago)