Sennheiser HMEC 26 Support Question
Sennheiser HMEC 26 Support Question
Find answers below for this question about Sennheiser HMEC 26.Need a Sennheiser HMEC 26 manual? We have 3 online manuals for this item!
Question posted by stephenhayward46 on October 3rd, 2021
Sennheiser Hme26-2-2t Replacement Parts
what type of cable runs thru the top of the headset. I am looking for a replacement for the noise cancelling HME 26-2-t but can't seem to find anywhere. Found a hme 46 cable but one wire short
Current Answers
Answer #1: Posted by SonuKumar on October 4th, 2021 12:56 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,633,680
Member since:
May 9th, 2021 Points: 16,633,680
https://www.manualslib.com/manual/587767/Sennheiser-Hmec-26-2.html?page=22
its cat cable.. check manual
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Sennheiser HMEC 26 Manual Pages
Cell Phone Compatibility - Page 1
... make a binding declaration with NoiseGard™
active noise compensation.
̈ Connect the adapter cable (type a or b, see table below) to the following Sennheiser aviation headsets:
Aviation headset HME 95 HMEC 250* HMEC 460*/HMEC 466* HMEC 26/46 with -BV-K* or -BV-KP* cable * Headset with NoiseGard™ active noise compensation
The following characteristics and are compatible with...
Instructions for use Control Unit ASO - Page 1
... (ASO) automatically switches NoiseGard™ off when the headset is delivered ex-works when the "auto shut-off . KG Am Labor 1, 30900 Wedemark, Germany www.sennheiser.com A01 / Publ. 02/2010
Activate "auto shut-off" by setting the switch to the position ASO. HMEC 26 / HMEC 46 / HMEC 460
Auto Shut-Off (ASO)
Die Funktion „Auto...
Instructions for use - Page 2
...Before operating any aircraft, make sure that, with
HMEC 26-2 | 1 Remove the rechargeable batteries if the ...parts out of reach of children who could swallow smaller pieces.
̈ Switch the product off after use the headset for making phone calls or listening to music.
̈ With the NoiseGardTM noise compensation switched on, typical aircraft sounds (for extended periods of at www.sennheiser...
Instructions for use - Page 3
.... All other parts of producing sound pressure exceeding 85 dB(A). Contact your Sennheiser partner.
2 | HMEC 26-2 Preventing damage ...replacement is capable of the product must be replaced by your Sennheiser partner or the Sennheiser Service Department. ̈ Only replace parts of time to repair a defective product yourself. Do not listen at high volume levels for continuous noise...
Instructions for use - Page 5
... • Single-sided cable, easy to 18 dB - The noise-compensating condenser microphone ensures excellent speech transmission even in aircraft cockpits. consequently the radio volume can be decreased
• Lightweight • Extremely comfortable to wear due to the patented two- The HMEC 26-2 headset
The HMEC 26-2 headset
The HMEC 26-2 headset with NoiseGard™ professional...
Instructions for use - Page 6
.../rechargeable batteries
• "Auto shut-off" extends battery life • TalkThrough function (HMEC 26-2-T only) • ETSO approval C139 • 5 year warranty
Package contents
1 HMEC 26-2 headset 1 cable clip 1 wind and pop screen 1 pair of hygiene pads 1 audio cable with 2.5 mm jack plugs* 1 audio cable with 3.5 mm jack plugs* 1 belt clip* 1 carry bag* 1 instruction manual 1 EASA Form...
Instructions for use - Page 7
Operation
Operation
Putting on the headset When putting on the headset, the patented two-piece headband adjusts automatically. Flipping away one earcup The headset features a "flip-away" earcup for single-sided listening.
6 | HMEC 26-2
Instructions for use - Page 8
This allows the headset to be rotated.
Always use the supplied wind and pop screen. HMEC 26-2 | 7
Operation Positioning the microphone Bend the flexible microphone boom so that the microphone is placed at the corner of the head. Turning the microphone boom ...
Instructions for use - Page 9
Make sure that
you can damage your audio system. This headset is capable of your hearing! ̈ Set the volume to change the microphone sensitivity.
+ -
8 | HMEC 26-2
Higher volumes or longer durations can hear critical sounds such as warning alarms. Adjusting the microphone sensitivity Turn a small screwdriver in the direction of the ...
Instructions for use - Page 10
The control units of the HMEC 26-2
The control units of the HMEC 26-2
Control unit I
1 Volume controls 2 LED 3 NoiseGard™ ON/OFF switch 4 Mono/stereo switch k/kk 5 BOOM switch L/R 6 3.5 mm jack socket 7 Battery compartment 8 2.5 mm jack socket
Headset with control unit I
Cable -BV-K-2 Cable -B-K-2 Cable -B-KP-2 Cable -B-CP-2 Cable -V-KX-2
Operating element 12345678
HMEC 26-2 | 9
Instructions for use - Page 11
The control units of the HMEC 26-2 Control unit II
2 LED 3 NoiseGard™ ON/OFF switch
Headset with control unit II Cable -CP Cable -CP-2 Cable -KP Cable -KP-2 Cable -NP Cable -RP-2 Cable -DP-2
Operating element 12345678
10 | HMEC 26-2
Instructions for use - Page 12
OFF
NoiseGard™ is off.
HMEC 26-2 | 11
The LED 2 is switched off. With NoiseGard™ switched off, the headset can be used as a conventional headset.
̈ Set the NoiseGard™ ON/OFF switch 3 to switch the NoiseGard™ active noise compensation on . Using the headset
Using the headset
Switching NoiseGard™ on/off
The NoiseGard™ ON...
Instructions for use - Page 13
This headset is rotated to permit left and right stereo channel The position "R" or "L" of the BOOM switch 5 corresponds ... of producing high sound pressure levels. To move the BOOM switch, use a pointed tool.
12 | HMEC 26-2 CAUTION
Hearing damage due to a medium level. Using the headset
Adjusting the volume The two slide volume controls 1 allow you to adjust the volume for the left or...
Instructions for use - Page 14
... the NoiseGard™ electronics off when the headset is sufficient. You can activate "auto shutoff" as follows:
HMEC 26-2 | 13 lights up yellow The battery capacity...rechargeable battery capacity:
LED 2
Meaning
lights up red The batteries are switched off. Replace the batteries. Using the headset
Powering NoiseGard™ via two (rechargeable) batteries ̈ Insert two 1.5 V ...
Instructions for use - Page 15
Switching the TalkThrough function on/off .
14 | HMEC 26-2 With TalkThrough switched on, a separate microphone 9 picks up .
Unwanted background noise is filtered out, only allowing the voice of ambient noise. Using the headset ̈ Set the switch to switch the TalkThrough function
on. The LED < lights up acoustic signals in the immediate vicinity. Press the button...
Instructions for use - Page 16
...! CAUTION Danger of accident due to connect a mobile telephone. HMEC 26-2 | 15 For this purpose, the NoiseGard™ active noise compensation must be switched on .
A suitable adapter for your mobile...; active noise compensation is available from your attention and may cause accidents. ̈ During flight operation, do not use the headset
for telephone calls! Using the headset
9
<...
Instructions for use - Page 17
... attention! However, the functions of the manufacturer.
Using the headset
̈ Connect the audio cable to the 2.5 mm jack socket 8 on the control unit I and to the corresponding jack socket on your attention and may cause accidents. ̈ During flight operation, do not use the headset
for listening to additional audio sources!
16 | HMEC 26-2
Instructions for use - Page 20
Care and maintenance
Care and maintenance
Cleaning and maintaining the headset CAUTION Liquids can short-circuit the electronics or damage the mechanics. Liquids entering the product can damage the product! HMEC 26-2 | 19
Replacing the ear pads For reasons of hygiene, you should replace the ear pads annually. ̈ Grasp the edge of the product from the...
Instructions for use - Page 22
.... No. 505689 Cat. No. 504062
HMEC 26-2 | 21 No. 505683 Cat. No. 502595
Cat. No. 500852 Cat. No. 505690 Cat. No. 505684 Cat. No. 505687 Cat. No. 505686 Cat. No. 505688 Cat. No. 505685 Cat. No. 505682 Cat. Accessories and spare parts
Accessories and spare parts
By changing the cables, you can simply retrofit different...
Instructions for use - Page 28
Specifications
Microphone incl.
preamplifier
Type
HMEC 26-2:
BKE 46
HMEC 26-2-1/T: BKE 46-1
Transducer principle
pre-polarized condenser microphone, noise-compensating
Frequency response
100 - 6,000 Hz
Output voltage
adjustable from 17-100 mV/Pa
HMEC 26-2:
80 mV/Pa -2 dB
factory preset: = 800 mV -2 dB at 114 dB SPL
HMEC 26-2-1/T: 60 mV/Pa ±1 dB factory preset: = 600 mV &#...
Similar Questions
Reparación De Conector Xlr 5 Pines
Cómo va la configuración de los cables para soldar xlr 5, ya que se trozo el cable y no te...
Cómo va la configuración de los cables para soldar xlr 5, ya que se trozo el cable y no te...
(Posted by JorgePerez157 1 year ago)
Mm100 Rechargable Battery Replacement
how to change the rechargable battery which does not get charged properly anymore
how to change the rechargable battery which does not get charged properly anymore
(Posted by ididdump 3 years ago)
Headset Dw Pro 2, Blue Light On Base Station
Hi,I am using Senheiser Headset DW Pro 2, due to my hearing disorder. The first headset I had was ch...
Hi,I am using Senheiser Headset DW Pro 2, due to my hearing disorder. The first headset I had was ch...
(Posted by helenapersson 5 years ago)
Rfq : Hme-46-3ptt-6-500468
We Need Item # hme-46-3ptt-6-500468 For Purchase...can Someone Come Back To Us For Availablity ..tha...
We Need Item # hme-46-3ptt-6-500468 For Purchase...can Someone Come Back To Us For Availablity ..tha...
(Posted by marjorie74229 6 years ago)
Require Spare Part For Sennheiser Set 840-tv Stethoset Receiver (eu) Rr 840
The aluminium plate holding the swivel for in ear buds on the stethoset receiver has 2 missing teeth...
The aluminium plate holding the swivel for in ear buds on the stethoset receiver has 2 missing teeth...
(Posted by handja21 6 years ago)