Sharp XR 10S Support Question
Sharp XR 10S Support Question
Find answers below for this question about Sharp XR 10S - Notevision SVGA DLP Projector.Need a Sharp XR 10S manual? We have 1 online manual for this item!
Question posted by ashley86542 on December 21st, 2011
Angled Screen
the screen is angled up to the right , will not adjust.
Current Answers
Related Sharp XR 10S Manual Pages
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 1
MULTIMEDIA PROJECTOR
MODEL
XR-20X/XR-20S XR-10X/XR-10S
OPERATION MANUAL
Introduction Quick Start
Setup
Connections
Basic Operation
Useful Features
Appendix
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 6
...that the equipment must accept any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances ... does cause harmful interference to environmental considerations. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL XR-20X/XR-20S/XR-10X/XR-10S This device complies with Part 15 of the FCC Rules.
Disposal of ...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 7
... Read this operation manual, the illustration and the screen display are slightly different, depending on the projector.
1 Press BMENU. • The "Picture" menu screen for explanation, and may differ slightly from the actual display.
Using the Menu Screen
ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
RETURN...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 8
... Locking the Operation Buttons on 27 Turning the Power off (Putting the Projector into Standby Mode 27
Image Projection 28 About the Setup Guide 28 Adjusting the Projected Image 28 Switching the Input Mode 30 Adjusting the Volume 30 Displaying the Black Screen and Turning off the Sound Temporarily 30 Correcting Trapezoidal Distortion ........ 31...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 12
...when setting up the screen in and turn on a level site within the adjustment range (8 degrees) of the adjustment foot.
8
Avoid locations with thin air, set up the projector in places exposed ... should only be cleaned more ) I Protect the lens so as mountains (at least 10 minutes. Neglecting this projector be installed in direct
sunlight or room light. I When you use in high-altitude ...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 14
... I 3 RCA to the wall outlet in your nearest Sharp Authorized Projector Dealer or Service Center.
10
and Singapore (6' (1.8 m))
QACCBA036WJPZ
For Australia, New Zealand and Oceania... I Remote receiver I Lamp unit
AN-C3CP2
AN-A1RS
AN-MR2
AN-XR20LP (for XR-20X/XR-20S) AN-XR10LP (for XR-10X/XR-10S)
Note
• Some of the optional accessories may not be available depending on the region...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 15
...adjusted on and putting the projector into standby mode.
Front View
Focus ring 28
For adjusting the focus.
Projector
Top View
Power indicator
27, 48
STANDBY/ON 27
button For turning the power on the menu. HEIGHT 29
ADJUST... 4.
37, 46
MENU/HELP button For displaying adjustment and setting screens, and help screen.
37
Adjustment buttons (P/R/O/Q)
For selecting menu items.
47 Intake ...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 17
...projector into the
standby mode. FORWARD/BACK buttons Same function as the [Page Down] and [Page Up] keys on a computer keyboard when using the optional Remote Receiver (AN-MR2).
AV MUTE button
30
For temporarily
displaying the black
screen... adjustment
46 and setting screens, and
help screen.
37
Adjustment buttons (P/R/O/Q)
• For selecting menu items.
• For adjusting the...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 19
... distance of the signal may malfunction under a
fluorescent lamp.
ture or high temperature. • The remote control may differ depending on the screen material. In this case, move the projector away from the remote control can be re- When using the remote control • Ensure that you do not drop, expose to...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 20
...
6 INPUT button
4 ENTER button
3 ON button
7 KEYSTONE
button
7 KEYSTONE button 4 ENTER button
4 Focus ring 4 HEIGHT
ADJUST lever
6 INPUT 1 button
1. Remove the lens cap and turn the projector on
On the projector On the remote control
_P. 27
16
Place the projector facing a wall or a screen _P. 18
2. Quick Start
This section shows the basic operation...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 21
... with the Setup Guide
1 After the projector turns on XR-20X.)
On the projector
Shrinks upper side. Turn the computer on the projector, input mode switches in the Setup Guide and adjust the focus, screen size, and height (angle).
3 After adjusting the focus, height (angle) and screen size, press TENTER to put the projector into standby mode. On the On the...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 32
... watching the projected image.
2 Adjusting the Screen Size
You can adjust the screen size using the zoom ring on the projector. Focus ring
28
Rotate the focus ring to "Off". (See page 42.)
Adjusting the Projected Image
STANDBY/ON button
ENTER button
Zoom ring
1 Adjusting the Focus
You can adjust the focus, height (angle), or zoom regardless of the...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 33
... area between the adjustment foot and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by adjusting the projector.
1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever.
2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. • The angle of projection is...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 35
... up to an angle of approximately ±13 degrees (when the resize mode is set to "NORMAL" (see page 32)).
1 Press g KEYSTONE to enter the Keystone Correction mode. • You can also display the on-screen display of the Keystone Correction mode with d KEYSTONE on the projector.
2 Press P/Q or O/R to adjust the Keystone Correction...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 38
...or Q 5 minutes s 6 minutes s 60 minutes • Shortens with Auto Sync function. ROn-screen display
Freezing a Moving Image
1 Press NFREEZE. • The projected image is operating the "Auto...Adjustment buttons (P/R/O/Q)
BREAK TIMER button FREEZE button
PICTURE MODE button
AUTO SYNC button
Auto Sync (Auto Sync Adjustment)
Auto Sync function works when detecting input signal after the projector...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 39
...INPUT 2, or when selecting INPUT 3 or INPUT 4. *3 Adjustment range for XR-20X/XR-10X. *4 Adjustment range for XR-20S/XR-10S. *5 An item which appears in the projector. ADJ
Picture Mode Contrast Bright Red Blue CLR Temp Bright...SEL./ADJ.
0 0 0 0 0 7500K 1
Standard
3D Progressive Bright
ENTER
END
"Screen adjustment (SCR-ADJ)" menu
Main menu
SCR - ADJ
Resize Image Shift
Keystone Auto Keystone ...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 41
...
0 0 0 0 7500K 1
Standard Bright
Help
SEL./ADJ. Picture
SCR - ENTER
END
Useful Features
37 Menu Selections (Adjustments)
Example: Adjusting "Bright". • This operation can also be performed by using the buttons on the projector.
1 Press BMENU. • The "Picture" menu screen for INPUT 1 (RGB) mode
Menu item
2 Press Q or O and select "Picture" to the previous...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 59
... _ _ _ 1 0% - 100% (Integer)
Model Name Check
T N A M _ _ _ 1 XR10S / XR10X /XR20S / XR20X
Model Name Check
M N R D _ _ _ 1 XR-10S / XR-10X / XR-20S / XR-20X
Projector Name Setting 1
P J N 1 * * * * OK or ERR
(First four characters) *1
Projector Name Setting 2
P J N 2 * * * * OK or ERR
(Middle four characters) *1
Projector Name Setting 3
P J N 3 * * * * OK or ERR
(Last four characters...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 62
...VGA
720 ´ 350 720 ´ 400
640 ´ 480
SVGA 800 ´ 600
XGA 1,024 ´ 768
SXGA 1,152 ´ 864
1,...projector supports other signals that conform to the
projector's native resolution. (1024 x 768 for the XR-20X and XR-10X models OR 800 x 600 for the XR-20S and XR-10S models). However, this projector... screen. • Optimum image quality will be achieved by matching your...
XR10S|XR10X|XR20S|XR20X Operation Manual - Page 66
... improvement, SHARP reserves the right to +60°C) Cabinet...adjustment foot and projecting parts) Weight (approx.) 8.6 lbs. (3.9 kg) Replacement parts Remote control, Power cord for U.K. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. and Canada, etc., Power cord for Europe, except U.K., Power cord for U.S. Specifications
Product type Projector Model XR-20X/XR-20S/XR-10X/XR-10S...
Similar Questions
Sharp Xr 10s - Notevision Svga Dlp Projector.
Main board needed. Where can I get? Used is fine. Budget $20
Main board needed. Where can I get? Used is fine. Budget $20
(Posted by sanoorvishwa 8 years ago)
How Do I Get Sound On The Sharp Projector Xr-55x?
The sound is coming from my computer, not the projector. The speaker setting is ON. I have pushed ...
The sound is coming from my computer, not the projector. The speaker setting is ON. I have pushed ...
(Posted by 12carol21 11 years ago)
Do You Have Power Cord For Sharp Notevision Projector Xr-1s
(Posted by susie8394 11 years ago)
Sharp Projector Xr-10k Won Light Up I Changed The Lamp Vol On Contr Board Are Ok
(Posted by ruestas01 12 years ago)
Projector Does Not Light A New Lamp.
Good morning. My projector was running normally, suddenly he turned off the lamp, but the system wor...
Good morning. My projector was running normally, suddenly he turned off the lamp, but the system wor...
(Posted by megaproducoes77 12 years ago)