Singer S10 I STUDIO Support Question
Singer S10 I STUDIO Support Question
Find answers below for this question about Singer S10 I STUDIO.Need a Singer S10 I STUDIO manual? We have 2 online manuals for this item!
Question posted by yvonneagostinho on September 3rd, 2017
Singer S10 Studio - Needle Going Crazy
I have a Singer S10 Studio I bought earlier this year in April. It only has about 20 hours of embroidery done on it... all of a sudden, in various places in my embroidery, the machine stops moving and the needle goes haywire, bouncing up and down. Sometimes I've been able to stop it with the Start/Stop button, but most times I've had to turn the power off. It's also shut itself off twice.
Current Answers
Answer #1: Posted by waelsaidani1 on September 3rd, 2017 1:13 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
Hello here is a video guide on how to troubleshoot this machine: https://www.youtube.com/watch?v=a9aezhg7jIk
Related Singer S10 I STUDIO Manual Pages
Instruction Manual - Page 1
All rights reserved. or its Affiliates. or its Affiliates. ©2014 The Singer Company Limited S.à.r.l. INSTRUCTION MANUAL S10
Singer and Studio are trademarks of The Singer Company Limited S.à.r.l.
Instruction Manual - Page 2
...and loose cloth.
5. Use this sewing machine and foot controller free from 8 years and above and persons with the ...sewing machine off ("O") position, then remove plug from the electrical outlet when removing covers, lubricating, or when making any air opening . 6. Read all moving parts.
An appliance should always be made by the manufacturer as described in the needle...
Instruction Manual - Page 12
... the thread end with your machine. The hook comes out through the needle eye. Need help selecting the right needle? q Needle threader knob w Hook
Step x
w
Draw the thread down as far as it will go.
NOTE SINGER® recommends SINGER® Style 2000 (woven) and 2001(knit) chromium needles for your hand. Push the needle threader lever down around...
Instruction Manual - Page 14
... sure to the rear.
Step c To check needle straightness, place the flat side of thread, needle type, fabric, and stabilizer are referenced in the Embroidery Quick Reference Guide on page 56.
14 Blunt, burred or bent needles can harm your machine. Embroidery tips on compatibility of the needle onto something flat (a needle plate, glass etc.) The gap between the...
Instruction Manual - Page 26
... buttons
26 z w
e x
Selecting Built-in Designs
Step z Your SINGER® Studio™ S10 embroidery machine
provides you with 55 ready-to display a list of thread colors used in the...3 5520 Blue
!0
!1 !2
!3
!3
Ready to sew screen will move to sew, press the desired pattern icon. The ready to Sew Screen Step z The LCD screen shows the following information.
Instruction Manual 2 - Page 3
... OF CONTENTS
1. GETTING STARTED SEWING Leveling machine 10 - 11 Setting up machine 10 - 11 Spool pins 12 - 13 Winding bobbin 14 - 15 Inserting the bobbin 16 - 17 Setting the top thread 18 - 19
Automatic needle threader 20 - 21 Picking up bobbin thread, Extension table, Feed dog control Attaching embroidery unit 62 - 63 Removing embroidery unit 62 - 63...
Instruction Manual 2 - Page 8
... 6. Screwdriver for further information.
8
2
3
4
6
7
8
10
11
12
14
15
16
18
19
20
21 Thread spool net (short)
16. Buttonhole foot
13. Satin stitch foot
14. Spool pin cap (small) 4.
Scissors 20. Embroidery software CD
17
FUTURA embroidery is a "system" of your Sewing machine is another
very useful foot and should be used for most decorative...
Instruction Manual 2 - Page 10
... balance of the power line cord into the cord socket (1) and your fingers be disconnected from needle plate area before using sewing machine only.
Poner el Interruptor de corriente/ luz de velocidad en "OFF"
Always disconnect the machine from power supply by turning it. * Use screwdriver (small) included in the accessories. 2.
Be careful not...
Instruction Manual 2 - Page 26
... the Auto / Default position you are easily determined by moving the Stitch Length and Width / Needle Position Control Knob.
A n a l t e r n a t e m e t h o d o f d e t e r m i n i n g available adjustments is selected, it will sound. Stitch length and width/needle position controls
*Auto/Default settings Your sewing machine will light in red beyond the potential adjustment range...
Instruction Manual 2 - Page 30
... as those in its center position.
Start/stop position selector switch C. Place the fabric under the presser foot toward you until the needle enters the fabric.
5
5. Needle stop switch (For embroidery only) E. Feed dog control F. Power/light switch
1B
C D E
A
F
2
H G I . When reaching the edge of
the machine, leaving about 6" (15cm) clear. 3. STRAIGHT STITCHING...
Instruction Manual 2 - Page 34
...4 (maximum).
5. Helpful Hint: Slight adjusting of the needle position to sew closer to the piping may stop in the beginning. INSERTING ZIPPERS To sew down the left of foot Aiguille à gauche du ...
3. If the machine stops from the beginning, push the start switch again.
34
Thread machine with a bias strip of fabric. INSERTING ZIPPERS AND PIPING
Use the zipper foot to sew to the right ...
Instruction Manual 2 - Page 58
... accionamiento
Be careful not to use full bobbin. Attach the embroidery presser foot behind presser bar so that the embroidery presser foot moves up and down together with the needle. PREPARATION FOR EMBROIDERY SEWING
BEFORE ATTACHING EMBROIDERY UNIT ATTACHING EMBROIDERY FOOT
Always be sure to turn off power to move needle up and down , and check that the drive lever...
Instruction Manual 2 - Page 74
...abort the installation procedure by turning the Hand wheel towards you.
2.
Next attach the embroidery unit to 100%. IMPORTANT: For switching from the small to the large hoop and ... Make sure the needle has been moved to the highest position by clicking on your sewing machine. If these steps are now ready to select and transmit a design to your computer and sewing machine.
1. If the ...
Instruction Manual 2 - Page 94
... button is pressed.
* Tacking stitch function for tie-off of other stitches ( ) The sewing machine makes 4 tiny tacking stitches to tie off of the tacking stitches will be lit red and needle will stop at down position whenever you stop switch (For embroidery only)
LED indicator Témoin a diode Indicador LED
Interrupteur marche/arrêt (Pour...
Instruction Manual 2 - Page 96
...before a new sewing project. FABRICS
THREAD
NEEDLES
The fabrics below can go.
6. Always disconnect the machine from power supply by pulling it can be of thread is a practical guide to needle and thread ...purple band
* Do not use on stretch fabrics. * For best sewing results, always use a Singer Branded Needle. Raise the needle bar to it toward the back
Côté plat orienté...
Instruction Manual 2 - Page 100
... power supply by the arrows. (A, B)
(2) (A) (B)
5. CAUTION
To ensure the best possible operation of sewing machine oil on the hook race as indicated by removing the plug from the wall-outlet. Raise the needle to keep the essential parts clean at all times.
1. Remove the bobbin case (2).
3
4. Clean the feed dogs and hook area...
Instruction Manual 2 - Page 102
... of oil other than Sewing Machine Oil
2
will cause damage to the points indicated
by arrows.
1
Screw Vis Guia
Face cover Plaque frontale Cubierta frontal
Helpful Hints : For the machine used . For the machine used after a long interval : It should be oiled before oiling.
F or best results always use SINGER Brand Sewing Machine Oil. OILING INSIDE THE...
Instruction Manual 2 - Page 104
... the three threads together under it easily. The twin needle is grooved on each needle from front to the back of a Singer Brand twin needle (Style 2025) is most useful for sewing satin stitches.
TWIN NEEDLE
A twin-needle produces two rows of parallel stitches for appliqueing and bar tacking. Place a spool on the bottom to permit dense stitching...
Instruction Manual 2 - Page 106
... particle is lowered when starting embroidery sewing. Raise needle by rotating hand wheel toward you.
attach embroidery unit or remove small hoop and turn off and on the control panel and/or PC screen. Needle thread breakage or incorrectly threaded condition is not connected. Connect your PC to the sewing machine with USB cable.
On...
Instruction Manual 2 - Page 112
... pull or push fabric while stitching.
Replace bulb with a damaged needle plate as this sewing machine is used or where oxygen is for all moving parts. Use only attachments recommended by pulling on cord. Return the sewing machine to install the proper outlet. "Never operate the sewing machine with the recycling symbol. Special care is marked with any...
Similar Questions
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Handwheel Won't Turn
I tried to thread the s10 machine and the handwheel will not turn at all. Is there a lock position f...
I tried to thread the s10 machine and the handwheel will not turn at all. Is there a lock position f...
(Posted by LoisM 7 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)
Will Singer H74 Sewing Machine Go Into Sewing Machine Table
(Posted by vogelgeos 10 years ago)