Snapper RE100 Support Question
Find answers below for this question about Snapper RE100.Need a Snapper RE100 manual? We have 1 online manual for this item!
Question posted by lflake11650 on September 8th, 2013
Brakeson Snapper Re100
My brakes don't work, The Park brake lever will not move up when brake pedal is depresed. I was given mower by friend for work I did for him thanks Lin Flake
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Snapper RE100 Manual Pages
Operater's Manual - Page 2
... you aware of established lawns and is not intended for any other purpose. It is a trademark of dependable service. This manual contains safety information to avoid them. Save these instructions thoroughly before attempting to the instructions in the Snapper brand. Copyright © 2011, Briggs & Stratton Corporation Milwaukee, WI, USA. Thank You for future...
Operater's Manual - Page 3
... Contents
Operator Safety 4
Features and Controls 9
Operation 10 Before Starting 10 Operator Seat Adjustment 10 Starting Engine 11 Engaging Mower Blade 13 Engaging Wheel Drive 13 Stopping Engine, Wheel Drive, Blade 14 Setting Park Brake 15 Cutting Height Adjustment 15 Reverse Lockout Mechanism 16
Maintenance 17 Maintenance Chart 17
r n General Maintenance 18
Storage...
Operater's Manual - Page 4
...slopes even though the brakes are often attracted to learn
stops ...DO NOT allow children or others
2. over
given rides in
serious injury or death to operate... contact Customer Service (1-800-935-2967
or www.snapper.com).
Fuels are explosive. Clean
blades off. ...Safety
! KEEP A SAFE DISTANCE (at the end of mower-related injuries.
1. grade) when equipped with the blade OFF...
Operater's Manual - Page 5
...
2.
mower to ... is extremely flammable
and the vapors are OFF and parking brake is in motion. STOP engine immediately after striking an... DO NOT start gas powered equipment in place and working. DO
NOT use accessories approved by the manufacturer.
Material...vehicle or
R trailer and refuel it on feet rests or pedal(s).
10. Remove gas-powered equipment from left side. See...
Operater's Manual - Page 6
...work under machine without safety blocks.
5. When draining fuel tank, drain fuel into an approved con- Use only factory authorized replacement parts or like parts when making repairs.
6
www.snapper... out of the reach of control.
8. Mower blades are in manual to
dling them.
... away from spark plug(s).
1. Check brakes frequently; Keep all cotter pins are sharp...
Operater's Manual - Page 8
... wear goggles when
r working with battery. Use only constant voltage battery
chargers made for tion Non-Spillable Battery - 7105102
WARNING Not duc AVOID SERIOUS INJURY OR DEATH
Read Operator's Manual before
7105102
Use only rechargeable valve regulated (sealed) non-spillable batteries in this product. Operator Safety
7103219
Parking Brake - 7103219
7104796
Reverse Lockout...
Operater's Manual - Page 9
Features and Controls
I .
Blade Lever
H.
Park Brake Latch
F.
Ignition Switch
D.
Engine Speed Control
B.
Fuel Tank
9
Steering Wheel
I
J
H
G F
E
RNeopt rfoodr uctiBonA
C
D
Features ...differ from your dealer if you have questions. Contact your specific model.
Transmission Shift Lever
J. Clutch/Brake Pedal
E.
Cutting Height Lever
C. Blade Pedal
G.
Operater's Manual - Page 11
...)
IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way
down , and the Blade Lever is in a drive position. The operator should be in a drive position. Refer to the (N) Neutral
position. IMPORTANT: DO NOT start...
Operater's Manual - Page 12
... (B) over , but will not start the engine with the transmission
N d shift lever in a drive position. Should the battery be started with the Park Brake engaged, and the Blade Lever is equipped with a
smooth, even motion until the engine runs smooth.
12
www.snapper.com Follow starting instructions
carefully. On Model 3317524BVE, the engine is in...
Operater's Manual - Page 13
... behind and down for adjustment
procedures or return machine to begin forward motion.
5. A Figure 11: Engaging the clutch/brake pedal
Not fodruction B pro Figure 10: Engaging the mower blade Re Wheel Drive
A
1. Place the transmission shift lever (A, Figure 12) into a slow forward speed and the engine speed control to the "FAST" position.
2. Release the...
Operater's Manual - Page 14
... neutral and engage park brake.
Remove key. WARNING
! Once blade is adjusted and functioning properly. Engine, Wheel Drive, Blade
Engine
1. Mower Blade
1. Stop the engine by turning the key (A, Figure 13) to r apply the brake. Stop motion of the Rear Engine Rider by releasing the blade pedals (A, Figure 15) or moving the blade lever (B) rearward to...
Operater's Manual - Page 15
... by pressing down , slide the park brake latch (B) all the way down firmly on slopes. Operation
Stopping - To set the park brake, press the clutch/brake pedal (A, Figure 16) all the way in the park brake latch will slide back to the engaged position, and release the clutch/brake pedal.
Engine, Wheel Drive,
Blade (Continued)
Park Brake
1. Cutting Height Adjustment
1. DO NOT...
Operater's Manual - Page 18
...Engage parking brake....its
rear bumper.
18
www.snapper.com Stop filling the tank when
fuel collects in the filler neck. • Empty the fuel tank before working on engines equipped with new ...3. After all parts to the engine manual for straightness. Engine
Check Mower Blade
and components are HOT. lbs. 4. entitled "ADJUSTING MOWER BLADE". DANGER
! N d A
wear or damage on this page....
Operater's Manual - Page 19
... the engine "OFF", move the blade lever e back to cool before operating the machine.
WARNING
! The blade should stop rotating in less than 1".
If the blade continues to
the deck. "BLADE BRAKE ADJUSTMENT", or contact your
MENT". Service Brake / Park Brake
1. The rear tires should be completed before working on the left side of cut position...
Operater's Manual - Page 20
... carburetor side of seat with Clutch/Brake Pedal not fully depressed.
Rear Axle Bearing. Shift Lever. DO NOT operate machine if any safety device. Change the air filter: • Pull up and rotate the air cleaner latch (A, Figure 23) to the section entitled
"MOWER BLADE SPINDLE - Contact your SNAPPER dealer
immediately for inspection. Engine and...
Operater's Manual - Page 24
... 32) clockwise to cool before working on machine.
Fuel Filler Cap
must be made by an authorized
dealer. If the blades take
machine immediately to 3-1/4" clearance between the front of the blade lever (A, r Figure 31) and the edge of the plate. e 2. Figure 32: Adjusting blade brake tension
24
www.snapper.com However, if there...
Operater's Manual - Page 26
... the third position
(middle notch). Avoid serious burns, allow the pedal (A, Figure 37) to the section entitled "SERVICE BRAKE/PARK BRAKE ADJUSTMENT". Figure 36: Mower belt adjustment
2.
STOP engine.
Move the blade lever up and over to check Clutch/Brake Cable slack. Place the deck cutting height lever in the "ON" position, the distance
should measure 1-1/4" but no...
Operater's Manual - Page 27
... the park brake lever (B) in
the "ON" position and release the clutch/brake pedal to prevent fuel spillage.
4. After adjustment is more than 5 feet,
the wheel brake should be...brake cable (adjustment shown in the filler neck.
• Empty the fuel tank before working on machine. ot uc A RNeprod B
B
D
A
C D
Figure 39: Adjusting the brake cable
5. Figure 38: Setting the park brake...
Operater's Manual - Page 28
...www.snapper....mower blade
IMPORTANT
around cutting blades. DO NOT attempt any adjustments, maintenance, service or
repairs with new blade. Reinstall the blade.
D C
Mower Blade Replacement
Blade Wear Limits
1. Maintenance
! Fuel Filler Cap
must be closed securely to the spindle.
4.
ot foruction A
B C
N rod Figure 41: Mower blade wear limits
ep ! Engage parking brake...
Operater's Manual - Page 32
.... If broken, replace with new battery cables. 11. Sit in fuel system. Clean free of balance or bent mower blades. 1. Replace filter. 5. Excessive Vibration
1. Loose blade components.
2. Replace pulley.
32
www.snapper.com Faulty parking brake, blade or ignition switch. 5. Turn ignition switch to proper torque.
4.
Engine air pre-cleaner and or air cleaner...
Similar Questions
Replacement Battery For Snapper Re110
What battery size is needed for Snapper RE110 riding lawn mower?
What battery size is needed for Snapper RE110 riding lawn mower?
(Posted by yellgirl 1 year ago)
How Do I Tighten The Blade Belt On A Re 130 Re Series Snapper Riding Lawn Mower
(Posted by dobbsnick919 1 year ago)
Will Not Pull Up Small Incline
snapper re100 will not pull up incline. I Removed rear cover (yoke) found clutch (rubber wheel) is l...
snapper re100 will not pull up incline. I Removed rear cover (yoke) found clutch (rubber wheel) is l...
(Posted by samnickel 6 years ago)
Lawn Mower Wont Start
I have sp80 ran over small stump mower stopped, started again and ran until I stopped it to empty ba...
I have sp80 ran over small stump mower stopped, started again and ran until I stopped it to empty ba...
(Posted by cissy0 8 years ago)