Stihl HT 131 Support Question
Stihl HT 131 Support Question
Find answers below for this question about Stihl HT 131.Need a Stihl HT 131 manual? We have 1 online manual for this item!
Question posted by pasqua on July 10th, 2015
No Gas Into Stihl 131 Carb
Pole saw will not start. New plug - that remains dry even after priming. Have removed carb cover, and gas line was pressurized (presumably after priming). Is it possible to remove the white plastic piece that the gas line connects to - I assume that this is clogged as even with air pump there is no air into carb? Or, any other advice. thanks R Johnson pasqua lake, Sask
Current Answers
Answer #1: Posted by hzplj9 on July 10th, 2015 12:07 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,670
Member since:
June 25th, 2012 Points: 4,875,670
This is a link to carb adjustment forum answers.
http://www.forestryforum.com/board/index.php?topic...
If you are having continuing problems with running then a carb gasket replacement could be a solution. Search through auction sites or contact a local dealer who could supply the kit. Solves a large amount of issues.
Related Stihl HT 131 Manual Pages
Product Instruction Manual - Page 3
...before using your pole
47 pruner. Contact your STIHL dealer or the STIHL
distributor for your STIHL pole
45
pruner, it... Harness
23
Backpack Carrying System
24
Starting / Stopping the Engine
25
Operating ...Saw Chain
36
{
HT 100, HT 101, HT 130, HT 131
Inspections and Maintenance by Dealer
Maintenance and Care
Main Parts
Specifications
Special Accessories
Maintenance and Repairs
STIHL...
Product Instruction Manual - Page 4
...procedure. your machine differs from time to operate manual fuel pump
Manual fuel pump
Warning! STIHL's philosophy is to continually improve all of its individual components.
Caution! As a result...HT 101, HT 130, HT 131
N Lever (2) ...
Fuel tank for gasoline and engine oil mixture
Tank for assistance. Depending on the model concerned, the following pictograms may be covered ...
Product Instruction Manual - Page 5
...sure that you have different parts and controls. Warning! The use of whitefinger
HT 100, HT 101, HT 130, HT 131
3 If the cutters contact your model.
g.
Working with any substance (drugs... are mentioned as high vibration levels and long periods of a pole pruner involves
1.
during a work , check with your STIHL dealer show you get tired, take a break. the use may...
Product Instruction Manual - Page 6
... the above shoulder level. Warning!
Wear sound barriers (ear plugs or ear mufflers) to hear warnings (shouts, alarms, etc...with adequate top and side protection complying with constant, excessive pressure. To reduce the risk of their physician and the ...STIHL unit produces an electromagnetic field of the power tool parts see the chapter on "Main Parts".
4
HT 100, HT 101, HT 130, HT 131...
Product Instruction Manual - Page 7
... hot muffler away from escaping gas vapor and fumes, remove the fuel filler cap on ...pressure build-up inside the fuel tank depending on your STIHL servicing dealer. Gasoline is running.
Warning! If this machine if it checked by your clothing.
HT 100, HT 101, HT 130, HT 131
5 g. In case of your power tool carefully so as to allow it has been completely removed...
Product Instruction Manual - Page 8
...proper condition and operation before starting, particularly the throttle trigger,... tank opening lining up and/...Always check your authorized STIHL dealer for additional ...when the positioning marks line up . Insert the ...at tightening.
Before Starting
Take off and ...guard (scabbard) and inspect the pole pruner for installation, turn ). ...possible. this STIHL cap, raise the grip ...
Product Instruction Manual - Page 9
... from the fueling spot, outdoors only. Place the pole pruner on the spark plug - To reduce the risk of your power tool.
275BA006 KN
English
Warning! Check that could ignite combustible fumes and cause a fire.
HT 100, HT 101, HT 130, HT 131
7
Keep the handles clean and dry at starting instructions, see appropriate chapter of control, do not...
Product Instruction Manual - Page 10
...avoid stumbling.
Work carefully.
8
HT 100, HT 101, HT 130, HT 131 Wrap your pole pruner, always maintain good balance ...pole pruner is running cutting tool, do not use a lift bucket. Be extremely cautious when working . Operate it at a height above shoulder height. At correct idle speed, the saw chain should follow these instructions, too. Working Conditions
Operate and start...
Product Instruction Manual - Page 12
...the general condition of your power tool using the starting throttle position, as rocks, fences, nails and... saw chain. Keep work area clear - Electricity can jump from one point to another by means of the branch.
10
HT 100, HT 101, HT 130, HT 131...vibrate loose and fall , and remove all tools and equipment at least 50 feet (15 m) between the pole pruner (including any wires or
cables...
Product Instruction Manual - Page 13
... HT 100, HT 101, HT 130, HT 131
...dry brush, grass, wood chips or other parts of fire and burn injuries, the following specific safety precautions must be damaged and cause an increase in the muffler.
Remove excess lubricant and all debris such as the limbed branch starts to reduce the possibility...plug) become hot during operation and remain hot for falling wood! Warning! Hold the pole...
Product Instruction Manual - Page 14
...suddenly stopped by a STIHL servicing dealer. Because of the design of ...1. Never let the nose of the pole pruner, the reactive forces experienced when...nose at full speed.
12
HT 100, HT 101, HT 130, HT 131
The reaction of fire or burn... reduce the risk of the chain pulls the saw chain near wire fences and when cutting small,...start a cut limbs with the chain rotating at all times.
2.
Product Instruction Manual - Page 15
... work not described in your instruction manual. Use the specified spark plug and make sure that the risk of non-STIHL parts may drive the saw rapidly straight back toward the operator. Never test the ignition system with the ignition wire boot removed from an underbuck cut more than one limb at the top...
Product Instruction Manual - Page 16
... most comfortable position.
14
HT 100, HT 101, HT 130, HT 131 Before storing for longer than...pressure washer. N Starting the engine N Put on the wood. Never stand directly underneath the branch you after each use.
Disposal
HT 100, HT 130 Always hold the shaft with your left hand in a dry... the maintenance chart in several controllable pieces.
risk of children. The least ...
Product Instruction Manual - Page 20
... on the 4-stroke principle. Gasoline with various ethanol contents.
18
HT 100, HT 101, HT 130, HT 131
Fuel
This engine is certified to the engine. English
Adjusting the Throttle Cable
A properly adjusted throttle cable is the precondition for correct operation in such engines. this reason STIHL recommends that you use only high-quality unleaded gasoline!
Product Instruction Manual - Page 22
...the cap is not properly closed and the steps
20
HT 100, HT 101, HT 130, HT 131 N Turn cap clockwise as far as it can be repeated. STIHL recommends use of the STIHL filling system (special accessory).
249BA056 KN
249BA054 KN
N ...N Position the cap with the surface. N Remove the filler cap. Closing the toolless filler cap
described above must line up. the raised positioning marks must be...
Product Instruction Manual - Page 29
...for some time.
see "Tensioning the Saw Chain".
see "Adjusting the Carburetor".
N Start the engine by hand.
N Dry the spark plug.
see "Spark Plug". As all moving parts have to ...during this could damage the engine -
N Remove the spark plug - N Crank the engine several times with fuel. see "Spark Plug".
N Move the slide control to clear ...HT 100, HT 101, HT 130, HT 131
27
Product Instruction Manual - Page 37
... lubricant, e.g.
It is dry - N If you use of fuel properly in accordance with corrosion inhibiting oil. STIHL BioPlus, completely fill the chain oil tank.
English
Checking and Replacing the Chain Sprocket
N Remove the chain sprocket cover, chain and guide bar. N Dispose of original STIHL chain sprockets.
000BA054 KN
HT 100, HT 101, HT 130, HT 131
35
N Tighten down the...
Product Instruction Manual - Page 39
...FG 2, HOS or USG sharpener: Remove the chain from the inside to the..., take
away as little metal as possible - N Always file from the bar...files have an X in a straight line, wear quickly and finally break.
N...wear.
689BA043 KN
689BA018 KN
HT 100, HT 101, HT 130, HT 131
37
Cutter shapes
Angle (°...saw chains are sharpened to the angles marked on the file holder. STIHL saw...
Product Instruction Manual - Page 50
... either at STIHL Incorporated or at and after the first scheduled replacement point.
48
HT 100, HT 101, HT 130, HT 131 Any manufacturer-...Line - Clamps - Limitations
This Emission Control Systems Warranty shall not cover any of the following list specifically defines the emission-related warranted parts: - Warranty Work
STIHL Incorporated shall remedy warranty defects at an authorized STIHL...
Product Instruction Manual - Page 51
... BOSS®
HT 100, HT 101, HT 130, HT 131
Some of STIHL's Common Law Trademarks
BioPlus™ Easy2Start™ EasySpool™ ElastoStart™ Ematic™ FixCut™ HT Plus™ IntelliCarb™ Master Control Lever™ Micro™ Pro Mark™ Quad Power™ Quiet Line™ STIHL Compact™ STIHL HomeScaper Series™ STIHL Interchangeable Attachment Series...
Similar Questions
My Sg 20 Has A Broken Black Plastic Piece On Top Of The Pump Cylinder. Can I Buy
(Posted by worngrazers0g 1 year ago)
I Am Not Getting Any Oil To The Chain? Do You Have A Schematic Of The 131
Looking for a schematic of the 131.pole saw. I am not getting oil to the chain
Looking for a schematic of the 131.pole saw. I am not getting oil to the chain
(Posted by nffsim 7 years ago)
Ht 131 Pole Saw
my guy took aprt my ht131 and now i cant seem to get it back together so it will work properly they ...
my guy took aprt my ht131 and now i cant seem to get it back together so it will work properly they ...
(Posted by Kurttreeboss 7 years ago)
Primer Gas Bulb Is New & It Will Not Prime
Purchased new primer bulb & it will move some gas thru it but when i crank the machine it it onl...
Purchased new primer bulb & it will move some gas thru it but when i crank the machine it it onl...
(Posted by melonydunning 10 years ago)