iRobot Verro 500 Support Question
iRobot Verro 500 Support Question
Find answers below for this question about iRobot Verro 500.Need a iRobot Verro 500 manual? We have 1 online manual for this item!
Question posted by jadahle on January 15th, 2018
No Drive& No Pump: Dismantled Pump And Drive And Cleaned. Still Will Not Operate
Why will the electric motor not work? Power pack is lit up
Current Answers
Related iRobot Verro 500 Manual Pages
Product Manual - Page 2
... a Ground Fault Current Interrupter outlet.
Safety Notes
WARNING: Your cleaner should be consistent with water.
iRobot Verro Owner's Manual Always remember to protect your electric outlet and prevent any possible electric shock. Shut off and unplug the Power Supply every time you remove the cleaner from the pool. Do not leave the cleaner in...
Product Manual - Page 3
... floating power cord must be locked in water. Retain the safety and operating instructions for 15 to lift Verro from ...Power Supply in direct sunlight and avoid leaving it is not fully immersed in the socket on the Power Supply. This will fit into the socket only one way. Do not use the floating power cord to 20 minutes following the end of its cleaning cycle. It will allow the motors...
Product Manual - Page 4
... of the water pumped through its filter bag to improve coverage of the entire pool. (p. 8)
Tip Store Verro in loss of large debris (leaves, etc.), such as when the pool is not kept clean, Verro will not clean properly and will not be damaged by rain.
Tips
Tip Clean the filter bag regularly. The Power Supply is...
Product Manual - Page 5
Table of Contents
Anatomy 6 Parts List 7 Using Verro 8 - 10 How Verro Works 11 Cleaning the Filter Bag 12 - 13 Maintenance and Adjustment 14 - 18 Troubleshooting 19 - 20 Customer Care 21
www.irobot.com
Product Manual - Page 7
... 13. Cable Assembly 16. Wheel Tube Assembly 19. OFF button 20. Light 21. ON button 22. Drive Track 8. Filter Screen 10. Side Plate 11. PVA Brush 12. Power Cord (Outlet) 23. Drive Motor 4. Power Supply (Transformer) 17. Outlet Top 2. Pump Motor 3. Pulley Assembly 6. Bottom Lid Assembly 14. Transformer Socket 18. Vacuum Intake Flaps 24. Lock Tabs
www...
Product Manual - Page 8
... is right side up and level.
4 Place the Power Supply (transformer) at least 3.5 meters /12 feet from side to side to allow air to the bottom of the handle. Ensure that it from the pool. 3.5m/12ft
iRobot Verro Owner's Manual Each time Verro cleans the pool, reverse the direction of the pool. Let...
Product Manual - Page 9
... feet from the pool and plug it will only go in when Verro is ON. To
stop Verro before the end of the cleaning cycle will start Verro; ON: Green button turns robot ON.
The length of the cleaning cycle, press the red Power button on pool size.
Be sure not to force the plug as...
Product Manual - Page 10
... the plug counter-clockwise to unlock it).
Using Verro (cont...)
8
When Verro has finished cleaning the pool it will stop automatically and the Power Supply light will drain from Verro as it from the power outlet before removing Verro from the GFCI outlet. Shut off and unplug the Power Supply every time you remove the cleaner from the...
Product Manual - Page 11
....com 11
Verro's coverage algorithm allows Verro to brush and clean your pool so that pumps 80 gallons of water per minute through the top helps Verro maintain traction ...500 microns in size.) The force of the water being pumped up , along with all the way from the bottom to the walls and bottom of your pool all of the other loose dirt and debris.
How Verro Works
Verro has a powerful motor...
Product Manual - Page 12
... the sides of the water pumped through the filter bag to prevent scratching the robot's shell). If the filter bag becomes clogged, Verro will not be able to clean as effectively and may have ...trouble moving along the bottom and up the walls properly.
1 Unplug the Power Supply. (Please keep the plug away...
Product Manual - Page 13
... the inside out and rinse away any accumulated debris with a hose. Gently agitate and squeeze the bag while rinsing it back on the support bars.
Cleaning the Filter Bag (cont...)
4 Remove the filter bag assembly.
5 Remove the filter bag from the support bars.
6 Turn the filter bag inside and the smooth...
Product Manual - Page 14
If you rinse Verro with the drive belts. They will need to replace them when Verro is water resistant, but not waterproof and may be replaced. The Power Supply is riding on its side tracks ...result in a dry place out of the robot with a garden hose after using it ) from the Power Supply.
2 Place Verro upside down on a towel and remove the filter bag assembly. (p. 12)
3 Locate the side of...
Product Manual - Page 15
...the new brushes onto the wheel tubes.
9 Place the brushes back in robot, reinstalling the drive belts and drive tracks over the end hubs.
10 Replace the side plate.
11 Reattach the four screws. Side ...Plate
5 Note the arrangement of the drive belts and drive tracks and then remove the front and rear brush rollers.
www.irobot.com 15 Wheel ...
Product Manual - Page 16
...the side plate. They will be happy to provide assistance.
1 Place Verro upside down on its drive wheel. You may have any difficulty, please call our customer care representatives at ...877.855.8593. When this happens, Verro may move more slowly and may also occasionally hear a click as the drive belt slips on a towel and remove the filter bag assembly. (p....
Product Manual - Page 17
....com 17 Verro is designed to travel around your hand, walk away from the Power Supply. 2 Place Verro so that you...drive belts. 6 Install the new drive belts and drive tracks. 7 Replace the side plates. 8 Reattach the four screws on the surface of the handle before each side.
However, if the cord tangles or kinks and will not lie properly on each cleaning run helps keep the floating power...
Product Manual - Page 18
... (cont...)
4 If the cord is not fully untwisted by the time it is straight, simply give it a few more turns by hand.
Cleaning the Impeller
Outlet Top Propeller
1 Unplug the floating power cord from the Power Supply. 2 Remove the screws that attach the outlet top to the robot. 3 Lift off the outlet top...
Product Manual - Page 19
... filter bag gets clogged, Verro will not move as two microns across and can be Clean the filter bag. (p. 12) cleaned
The brushes,drive belts or drive tracks need replacing
Replace brushes, drive belts or drive tracks. (p. 16)
The floating power cord is tangled or kinked
The pump impeller is not Plug the Power Supply into the Power Supply.
www.irobot...
Product Manual - Page 20
.... (p. 12) cleaned
The brushes, drive belts or drive tracks need replacing
Replace drive belts and treads. (p. 16)
The floating power cord Use the Detangler to untwist the cord. (p. 17) stuck on which it may
get caught. of the pool.
The pump impeller is Clean the impeller. (p. 18) fouled
Verro gets The floating power cord is preventing Verro
Position the Power Supply...
Product Manual - Page 22
...© 2007 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. Register your iRobot®Verro™ today. Pricing and availability subject to purchase accessories at: 800.727.9077 or visit...
3000a.07 All rights reserved. iRobot is a registered trademark and Verro is a trademark of iRobot Corporation. Cover photo © Veer Incorporated 2002 - 2005. SAVE 15% on all...
Similar Questions
Verro 500 Pool Cleaner
Have a unit in which the pump starts up but the unit wont propel itself. Have checked the rollers be...
Have a unit in which the pump starts up but the unit wont propel itself. Have checked the rollers be...
(Posted by piperfarms 6 years ago)
Himy Verro 500 Irobot Vacum For The Pool Is Shorting Out When The Pump Motor Is
connected. I'm thinking its burn cause of the leaves collected and plugging it up. Part number AS000...
connected. I'm thinking its burn cause of the leaves collected and plugging it up. Part number AS000...
(Posted by palisaran 6 years ago)
Scooba 230 Did Not Complete Cleaning Cycle (still Water In Clean Bladder) And No
No checkmark, and when I started it up again, it ran out of power, it should have been fully charged...
No checkmark, and when I started it up again, it ran out of power, it should have been fully charged...
(Posted by amlemal 11 years ago)
When I Push Clean Button, A Light Comes On That Szays Check Tank But The Tank Is
(Posted by burrconway 12 years ago)