Ryobi AP1301 Support Question
Find answers below for this question about Ryobi AP1301.Need a Ryobi AP1301 manual? We have 4 online manuals for this item!
Question posted by midgiesdan2 on October 21st, 2011
Sharpening Ryobi Planer Knives
What is the proper sharpening angle for Ryobi AP1301 planer knives?
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Ryobi AP1301 Manual Pages
English Manual - Page 1
When properly cared for, it will give you for dependability, ease of operation, and operator safety.
Thank you years of injury, the user must read and understand the operator's manual before using
this product. SAVE THIS MANUAL FOR FUTURE REFERENCE WARNING: To reduce the risk of rugged, trouble-free performance.
PORTABLE PLANER
AP1301
Your...
English Manual - Page 2
... workmanship or materials in your RYOBI® power tool for a period of two years from the date of purchase. We will complete the work properly due to defective workmanship or ... TWO YEAR WARRANTY AND 30 DAY EXCHANGE POLICY One World Technologies, Inc., warrants its RYOBI® power tools with the original product.
This warranty only covers defects arising under this warranty. TABLE OF...
English Manual - Page 3
..., etc., all instructions listed below, may risk injury.
NEVER STAND ON TOOL. Don't leave tool until it was designed.
USE RIGHT TOOL. GENERAL SAFETY RULES
WARNING:
Read and understand all times.
MAINTAIN TOOLS WITH CARE. Failure to follow all tools should be properly repaired or replaced by removing starter keys.
DON'T FORCE...
English Manual - Page 4
.... Make sure blade is tight and not making contact with or without the use of accessories that accept the tool's plug.
DO NOT MODIFY the plug provided. Let the planer apply the proper feed rate.
CHECK THE FEED ROLLERS occasionally to be sure there are not completely understood or if in...
English Manual - Page 5
....
ALLOW THE CUTTER HEAD to reach full speed before using your planer.
ALWAYS TURN OFF TOOL before resuming operation.
ALWAYS STAY ALERT! Refer to them these chemicals...of work using the planer.
REPLACEMENT PARTS.
To reduce your exposure to these instructions also. Do not allow familiarity (gained from frequent use to perform properly, shut off the ...
English Manual - Page 6
... and safer. Read The Operator's Manual
To reduce the risk of the following symbols may be used on this tool.
Proper interpretation of injury or damage, avoid contact with side shields, or a full face shield when operating this product. Precautions that involve your hands away from ...
English Manual - Page 7
...serious personal injury, do not attempt to use only identical replacement parts. Call Ryobi customer service for repair. We recommend Wide Vision Safety Mask for use over... or serious injury.
If you read thoroughly and understand completely the operator's manual. Before beginning power tool operation, always wear safety goggles or safety glasses with this product until you do not use eye ...
English Manual - Page 8
... of a malfunction or breakdown, grounding provides a path of least resistance for lights cannot properly carry a power tool motor. If the saw does not operate when plugged into a matching outlet that can .... An undersized extension cord will overheat. Use the chart provided below to whether the tool is properly installed and grounded in a loss of power and the motor will cause a drop in...
English Manual - Page 9
....
As it securely against the table or fence during cutting operations. Snipe (planers) Depression made at any angle to the workpiece, that area which produces a square-sided notch or trough ...caused by the workpiece being dropped into the tool first. GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed and maintained, is bent (or set)...
English Manual - Page 14
...leave the workpiece with light planing cuts first. Planing with tools to make several cuts with the planer starting with uniform moisture to reach the desired thickness. Cutter...twisted, or knotted. WARNING:
Never plane a workpiece with side shields when operating power tools. Let the planer apply the proper feed rate.
Remember, light cuts create a finer finish than heavier cuts.
...
English Manual - Page 15
... to chip the workpiece. Avoid using severely warped wood as they are fed through the planer will prevent the tool from the switch and store in serious personal injury. In the event of tearing them.... TO TURN THE PLANER OFF: With the switch key inserted into the switch, lift the switch
to work against the grain can occur when the board is not properly supported. Raise the ...
English Manual - Page 16
... motor. OPERATION
ADJUSTING THE PLANING DEPTH
See Figure 7. PLANING
See Figure 8. If an object is used to function properly. should have planed the wood, check all measurements for material up to one side at the rear of the planer and receive the planed lumber by rotating the depth adjustment handle.
If the...
English Manual - Page 17
... If properly adjusted, the depth of the finished piece should
be the same as a mirror, touch the threaded
spindle where it meets the planer table. •...planer, shows the depth of picking up to heed this warning could result in .
Retighten the blade locking bolts securely. Replace dust hood; ADJUSTMENTS
WARNING:
Before performing any adjustment, make sure the tool...
English Manual - Page 18
... they are permanently lubricated and need no further attention. This will keep
them rust-free. Using the planer table as a mirror, touch the threaded spindle on or in contact with side shields during power tool operation or when blowing dust. CUTTER HEAD LOCK
LUBRICATION
Periodically, check all moving parts (spindle, roller surfaces...
English Manual - Page 19
... screws ( 1 ).
Using the notched end of the magnetic blade wrench, remove the blade from the planer ( 2 ).
If you are changing to the second edge of the blade, rotate the blade "end... firmly to plane inaccurately. Never replace one side without replacing the other debris can cause the tool to seat.
Visually check that it , but be careful not to use for resin buildup,...
English Manual - Page 22
PORTABLE PLANER
AP1301
• SERVICE
Now that you call 1-800-525-2579 for your tool, should a need ever exist for a complete list of ...REPAIR PARTS
When ordering repair parts, always give the following information:
• MODEL NUMBER
AP1301
• SERIAL NUMBER
Ryobi® is a registered trademark of Ryobi® Limited used under license.
983000-828 9-10-07 (REV:03)
ONE WORLD...
Repair Sheet - Page 3
MODEL NUMBER AP1301
The model number will be found on a plate attached to the motor housing. KEY NOS. 2-6 AND 91 1 HANDLE KNOB ASSEMBLY 1 ... 1 PINION 1 BALL BEARING (6203ZZ 2 WARNING LABEL (DUST CHUTE-1 1 WARNING LABEL (DUST CHUTE-2 1 WARNING LABEL (DUST CHUTE-3 1 CHUTE DUST (INC. RYOBI 13 in all correspondence regarding your PLANER or when ordering repair parts. HANDLE ASSEMBLY (INC...
Repair Sheet - Page 4
...A
DESCRIPTION
QTY.
* SCREW (M8 X P1.25 X 20 mm HEX HD 1 BLADE LOCKING PLATE 2 PLANER BLADE (19 X 1.8 X 344 2
SCREW 14 KEY (5 X 12 mm 1
BEARING RETAINER 1 * ...- May Be Purchased Locally
4 MODEL NUMBER AP1301
The model number will be found on a plate attached to the motor housing.
RYOBI 13 in all correspondence regarding your PLANER or when ordering repair parts. SPINDLE 1...
Repair Sheet - Page 6
...X 12 mm HEX SOC 2 OPERATOR'S MANUAL REPAIR SHEET (REV:01)
* Standard Hardware Item - May Be Purchased Locally 6 RYOBI 13 in all correspondence regarding your PLANER or when ordering repair parts. KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16...821065-3 983000828 983000828R 01-27-06
DESCRIPTION
QTY. MODEL NUMBER AP1301
The model number will be found on a plate attached to the motor housing.
Similar Questions
How To Change Blades Ryobi Ap 1301 Planer
change blades ryobi ap1301 planer
change blades ryobi ap1301 planer
(Posted by robbenconstructionllc 2 years ago)
How Do I Sharpen The Blades On My Ryobi Rgs 2500 Garden Shredder
I don't have a owners manual for my Ryobi RGS 2500 Garden shredder and was wondering how to sharpen ...
I don't have a owners manual for my Ryobi RGS 2500 Garden shredder and was wondering how to sharpen ...
(Posted by Gavin6273 11 years ago)
Blade Placement In Planer
when replacing blades does flat side of black[or unbevld]go against spindle or locking bar
when replacing blades does flat side of black[or unbevld]go against spindle or locking bar
(Posted by shanerwick 11 years ago)
Charger Has Green Light But Will Not Operate Any Of My Tools
riboyi lithium 18v P103 battery has a green light from charger but will not run andy of my tools
riboyi lithium 18v P103 battery has a green light from charger but will not run andy of my tools
(Posted by jmschaefer 12 years ago)