Makita EK8100 Support Question
Makita EK8100 Support Question
Find answers below for this question about Makita EK8100.Need a Makita EK8100 manual? We have 3 online manuals for this item!
Question posted by erikbogart on April 12th, 2016
Serial Number Location
I know this may seem like a dumb question, I just purchased a new ek7301 concrete cut off saw. I can't seem to find the serial number. I have located the identification plaque. I have a 4 digit number with a letter after it is all I have. Before I send in my warranty paperwork. I'm just trying to make sure this is the serial number. I doesn't say serial number specifically, and seems very short. That's k you in advance.
Current Answers
Answer #1: Posted by Odin on April 12th, 2016 5:51 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,640
Member since:
April 10th, 2010 Points: 41,236,640
The illustration at http://bit.ly/1oVK5Da should answer your concern.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Makita EK8100 Manual Pages
Owners Manual - Page 4
...cutting discs, trolley with dust catcher, and systems for heavy‑duty yet lightweight tools. Like our chain saws, the MAKITA Power Cuts...the following when using synthetic resin cutting discs 10 Cutting metal 10 Cutting masonry and concrete 10-11 Transport and storage 11 ...33-34
Packing
Your MAKITA Power Cut is consequently reuseable or suitable for purchasing a MAKITA product! We want ...
Owners Manual - Page 7
...with mineral oil products. Do not work the Power Cut must be checked for perfect function and operating safety according to a location at once.
- In particular, make sure that ...regulations when working with a protective layer provide protection against cuts and ensure a secure footing.
- Safety shoes equipped with the cutoff saw. Do not spill fuel. Fuel cannot be consumed in...
Owners Manual - Page 11
...;and‑forth motion.
- Keep the Power Cut away from place to plan the direction and sequence of the planned cut. Always check new cutting discs or cutting discs that have
been in storage to make sure...fuel tank and
run the tool at top speed for electric wires and cables! When putting cutting discs in a vehicle. CAUTION: Do NOT clean synthetic resin cutting discs with water or other...
Owners Manual - Page 12
... repair works described in association with the use of non‑MAKITA spares, accessories, or cutting discs increases the risk of injured people
-
Number of accident. To protect unusable cutting discs from the first aid box. Allow the Power Cut to occur in good working order. We cannot accept any maintenance work (burn hazard...
Owners Manual - Page 13
...
0.8" / 1.0" 5)
V‑belt
no .
965 300 481
Overall weight (tanks empty, without cutting disc)
lb
21.56
22.00
EK8100
Displacement
cu in (cm3)
4.9 (81)
Bore
in (mm)
2.05 (52)
Stroke
in
0.8"... speed 3) Outside diameter / arbor hole / thickness 4) Country-specific 5) HD
13 Technical data
EK7300
EK7301
Displacement
cu in (cm3)
4.5 (73)
4.5 (73)
Bore
in (mm)
1.97 (50)...
Owners Manual - Page 14
...
6
7
2
25
1
8
9
14
13 12 11 10
24 23
22
EK7301
1102 123456
Identification plate (12) Indicate when ordering spare parts
EMI OFB 973108
Makita Corporation, Anjo, Aichi, Japan Made in Germany
Serial number Year of manufacture
15 16
17
18 19
21
20
1 Handle 2 Filter cover for air filter and spark plug cap 3 Cover...
Owners Manual - Page 15
...pulley is marked on the arbour (7). Turn the disc slowly until the stop hole of the cutting disc must be an exact fit with the arbor or shaft. Always wear protective gloves! For the... Cut!
If the arbor hole is now blocked. Allen key 3.
Putting into operation CAUTION:
Always turn off the engine and pull off the spark plug cap before doing any work , use the assembly tools ...
Owners Manual - Page 17
... near flames, sparks or fire (explosion hazard).
Be especially careful when handling gasoline. 23 22 24 25
Fuels Caution:
This tool uses petroleum products (gasoline and oil). Fuel mixture This tool is designed for two-stroke aircooled engines (quality grade JASO FC or ISO-L-EGD), which has to be added to 1 part...
Owners Manual - Page 18
...environment and clog the exhaust channel in dry, cool and secure locations! Eyes can cause starting problems and damage the engine.Purchase only that amount of time, it into your eyes, immediately...The engine must be used up inside! Clean screw cap and tank after refuelling. order number T-00745 6.4 floz. Shake the finished mixture thoroughly before pouring it will decrease. If oil...
Owners Manual - Page 19
...: Always make starting speed. This pushes in both ways within its starting easier. Start the Power Cut only after the first ignition automatically closes the decompression valve. If this is not the case, take the tool to make sure that it . Grasp the grip (2). Press the rubber cover until you fuelled the...
Owners Manual - Page 22
... / Checking V-belt tension". IMPORTANT:
If the cutting wheel breaks during reassembly!
Loosen and unscrew the ...the cover (4).
CAUTION:
Start the Power Cut only after complete assembly and inspection.
IMPORTANT...new V-belt.
Clean out the inside of wear and tear, it is visible in the right places during cutting, the Power Cut...the Power Cut turn off the engine, remove the cutting disc, ...
Owners Manual - Page 25
... plug, CHAMPION RCJ-6Y or NGK BPMR 7A.
0,5 mm
Checking the ignition spark
Insert the combination tool (9) between the ventilation hood and cylinder only as shown in case of the suction head can cause ... the spark plug position the combination tool in order to ensure unimpeded fuel flow to the carburetor. Do not insert the combination tool into contact with the saw to pull the suction out of...
Owners Manual - Page 28
...is visible in the illustration. Repositioning the cutting attachment
Loosen nuts (5). Unscrew the nuts (5) and remove the cover (6).
10 11
Use the combination tool (8) to lever out the stop pin ...The illustration shows the V-belt for EK8100).
Unscrew the grip (10) and turn the protective hood (11) as shown in the middle position (1).
For cutting up against obstacles, such as fatiguing...
Owners Manual - Page 29
...the V-belt (14) over the V-belt pulley (15). If a rotation direction is marked on the cutting disc, make sure the disc turns in the side position. Damaged or misformed screen wires may result....
Remove the spark arrester screen (26). NOTE: The illustration shows the V-belt for EK8100).
Reassembly the spark arrester screen and tighten the screw.
25 26
29 Screw in and tighten ...
Owners Manual - Page 30
...especially suitable for wetting the disc during use of diamond cutting discs reduces cutting time significantly.
A depth limiter can be added for order number.
2
5
4
1 6 7
3
30
The water...possible to do straight cuts, while simultaneously enabling almost untiring working safety, ease of the discs make cutting easier. NOTE: Before mounting the EK8100 Power Cut on the side. For...
Owners Manual - Page 31
... functioning of modern cutoff saws and their safety‑related...you in mind that you with special tools and testing devices.
Only original spare ...
Muffler
Clean to determine the required spare part numbers, and will gladly provide you consult a MAKITA... of your local dealer.
Page
General
Entire Power Cut
Cutting disc
Clutch
Protection hood
Clean exterior, check for ...
Owners Manual - Page 33
EK7300 EK7301 EK8100
19
4a
25
26
27
22
28
24
* 29 30
31 32
33 Extract from the spare parts list
Use only original MAKITA parts. For repairs and replacement of other parts, see your MAKITA service center.
Owners Manual - Page 34
... 340 001 1 Screwdriver (carburetor) 19 395 174 140 1 Spark arrester screen
Accessories (not delivered with the Power Cut)
Diamond cutting disc 22 966 1 Please consult your MAKITA service center. Mains water connection, cpl. EK7300 EK7301 EK8100
Pos. Guide trolley DT2010 cpl. For repairs and replacement of other parts, see your MAKITA dealer!
- 394 228...
Flyer (English) - Page 1
... w/advanced directional air flowensuresclean air for added performance &long engine life
EFFICIENCY
SLRmuffler recyclesunburned fuel vapor, reducing scavenging-losses upto 15%improved consumption
VERSATILITY
Model EK8100
Change blade from central to outbound flush position for lateral
cutsin lessthan 2minutes
INCREASED PERFORMANCE.
Flyer (English) - Page 2
... registered trade dress of POWER CUTTER accessories. 16'' 81 cc.INDUSTRIAL POWER CUTTER
Model EK8100
FEATURES & BENEFITS
n Powerful 81 cc. For a complete listing, please refer to the...without prior notice. All specifications subject to saw performance
n Cutting arm position changes simply from center position to flush (outboard) position allowing cuts directly adjacent to curb edges, wall or...
Similar Questions
Trying To Remove Motor On Makita Vc4710 Vacuum
cant find a service manual for this vacuum
cant find a service manual for this vacuum
(Posted by fishbowl8d 5 months ago)
Plastic Blade Guard Sticks And Does Not Rise Smoothly.
How do I fix the plastic guard not rising easily without unsafely pushing down to hard on the tool. ...
How do I fix the plastic guard not rising easily without unsafely pushing down to hard on the tool. ...
(Posted by nathanseymour 9 months ago)
Where Is The Serial Number Located For A Mac5200 Compressor
(Posted by jreaton80071 10 years ago)