Maytag MHW5630HC Support Question
Maytag MHW5630HC Support Question
Find answers below for this question about Maytag MHW5630HC.Need a Maytag MHW5630HC manual? We have 5 online manuals for this item!
Question posted by brentaguilar22 on April 29th, 2024
F3 E1 Error
what does that mean. And is there any way to fix it at home with parts
Current Answers
Answer #1: Posted by INIMITABLE on April 30th, 2024 12:13 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,084,120
Member since:
April 3rd, 2020 Points: 2,084,120
Answer #2: Posted by SonuKumar on April 30th, 2024 10:24 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,623,780
Member since:
May 9th, 2021 Points: 16,623,780
The Maytag washer error code F03 E01 means two things. The main problem is your washer's control board can't sense the water level. This could be because of a bad pressure sensor, wiring, a bad control board, or a clogged air pipe. The other code tells you the door is locked.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Maytag MHW5630HC Manual Pages
Specification Sheet - Page 1
... MHW6630H, MHW5630H. All rights reserved. MHW5630HSpecSheetV01. ft. Front Load Washer
MHW5630H
Metallic Slate MHW5630HC
Also available in the U.S.A. Printed in :
White
MHW5630HW
Capacity
Total
... General Features & Properties
Quick Wash Cycle
Maytag® Commercial Technology
10-Year Limited Parts Warranty** on any wash cycle with Extra Power button. Others in hot water. ...
Owners Manual 1 - Page 4
....
Fabric softener is always dispensed in the "Washer Maintenance and Care" section of these and see the online "Cycle Guide"). NOTE: Do not add single-dose laundry packets, Oxi-type boosters, color-safe bleach,....
It is recommended that the bulk dispenser is correct (see an "Sd" or "Sud" error code appear in the same cycle with a non-HE detergent. For liquid detergent, push down ...
Owners Manual 1 - Page 5
...; Disable the Load & Go™ option before beginning the cleaning process.
This includes clearing piles of laundry in combination with affresh® Washer Cleaner or regular liquid chlorine bleach to thoroughly clean the inside your washer, which, in turn, may increase the rate at which soils and detergent accumulate.
3.
Pull back the seal...
Owners Manual 1 - Page 10
...washer walk." Install your Quick Start Guide.
See "Washer Maintenance and Care" for your Quick Start Guide. Add spacing of washer to reduce noise transfer. NOTE: For additional details (or information) specific to your model, refer to your washer in a basement, laundry.... Please contact your washer. Water remaining in washer after use may require additional parts.
You will need ...
Owners Manual 1 - Page 11
...per minute. install no higher than 96" (2.4 m) from the plumbing/drain. See "Alternate Parts."
Drain system can be purchased separately;
A 1/4" (6 mm) diameter to the Quick Start ...washer. IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of o leaking from bottom of washer. (Additional hoses may be installed using a floor drain, wall standpipe, floor standpipe, or laundry ...
Owners Manual 1 - Page 13
...slide elbow end of drain hose, squeeze clamp with separate directions; You may need additional parts with separate directions. Remove drain hose form (floor drain installations only)
Loosen bolts with... end of washer.
Slide each bolt and spacer to step 6. 2. Remove transport bolts from back of the drain hose.
For a laundry tub or standpipe drain, go to center of washer.
3. It...
Owners Manual 1 - Page 14
... faucets
IMPORTANT: To reduce risk of laundry tub. HELPFUL TIP: Make note of which hose is seated on bottom of hose failure, replace the hoses every 5 years. Connect Inlet Hoses
IMPORTANT: To avoid leaks, check that your water inlet hoses have flat washers at both ends. Washer must be inside standpipe; Use adjustable...
Owners Manual 1 - Page 15
....
13. Then turn the leveling foot clockwise to lower the washer or counterclockwise to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with floor, go to side. Rock washer to test foot contact
Secure drain hose to raise the washer. If all four feet are in firm contact with cable tie...
Installation Instructions - Page 4
... drain system
4.5" (114 mm)
39" (991 mm)
Minimum diameter for floor standpipe drain system. Laundry tub drain system
4.5" (114 mm)
min. 39" (991 mm)
1" (25 mm)
Minimum ...laundry tub must be inside standpipe. Wall standpipe drain system
24 in .2 (310 cm2)
1" (25 mm)
DRAIN SYSTEM
The drain system can be at least 39" (991 mm) from the floor; See "Alternate parts." Top of washer...
Installation Instructions - Page 6
Discard bolts and spacers.
Loosen bolts with clamp. For a laundry tub or standpipe drain, go to center of hole. See "Alternate Parts." Slide each bolt and spacer to step 6. IMPORTANT: Do not plug washer in Step 5. Squeeze clamp with pliers and slide elbow end of drain hose, squeeze clamp with separate directions. Pull bolts...
Installation Instructions - Page 7
... work properly. Do not use tape or sealants on coupling by hand until clear.
7 Damage can result. See "Alternate Parts".
6. Washer must be connected to water
faucets
4.5" (114 mm)
Place hose into a laundry tub, drainpipe, or bucket to tighten couplings an additional two-thirds turn. Water should be used. Do not use hoses...
Installation Instructions - Page 8
... down as shown in firm contact with cold water inlet valve. Screw coupling by hand until it is snug. Secure drain hose
Laundry Tub
Standpipe
Wall
4.54".5" (114 mm)
4.5" (114 mm)
4.5" (1143 mm)
Grip washer from side to test foot contact
Slowly turn . Not Level
LEVEL
Not Level
14. Check for leaks.
Owners Manual - Page 6
...to run the full duration of fabric and soils being washed. however, the display will leave your laundry load. Washing During the wash cycle, this option to delay the start a cycle or touch ...add a garment, you can be changed.
■■Faster spin speeds mean shorter dry times but may cause the washer to turn the washer on the type of 12 hours. NOTE: For best results when using ...
Owners Manual - Page 10
...If you have excess suds, try using a higher concentration number. Add laundry products as High Efficiency are concentrated. See "Washer Care" in formulation and their ability to reduce suds. Not all detergents...;■To add single-dose and Oxi-type boosters, see an "Sd" or "Sud" error code appear in the dispensers from the previous wash cycle. For example, natural, organic, or...
Owners Manual - Page 11
... can plug pumps and may cause damage to the detergent dispenser. USING YOUR WASHER
First wash cycle without clothes. Synthetics, knits, and corduroy fabrics will pick up lint from sturdy fabrics.
NOTE: Always follow fabric care labels and laundry product instructions. Improper usage may require a service call.
■■Close zippers, fasten...
Owners Manual - Page 12
... move freely for best cleaning and to dispensers. Make sure no items are resting on type of sorted items loosely in mesh garment bags. Load laundry into washer. See "Cycle Guide" for every load, the dispenser will not dispense correctly.
12 NOTE: Do not add single-dose...
Owners Manual - Page 20
... corrected, touch POWER once to complete or the error code cannot reset. "Lo" "FL" appears on display, or F8 E1 or "Lo" "FL" appears on washer may be keeping the door from drain hose.
The...114 mm). F5 followed by E2 or F05 followed by E01 (drain pump system error) appears in display
Check for items in washer.
Use only HE detergent.
Check that may be allowed to clear the code....
Owners Manual - Page 21
... www.maytag.com/product_help - Washer beeps when START is locked. This means that your washer detected an off balance load ...and that the
control is closed for 1 full second.
Then touch POWER again and restart the washer. Open and close the door to possibly avoid a service call for 30 seconds, then plug back in display
System error...
Owners Manual - Page 22
...or clogged sink or drain. Drain hose connection.
Remove strainer/nylon stocking from washer" in washer drain system.
Avoid washing single items. Balance a single item such as ...attached tightly. Properly seat all household plumbing for leaks (laundry tubs, drain pipe, water pipes, and faucets).
See "Level the Washer" in the balancing system are removed during the spin/drain...
Owners Manual - Page 28
... for assistance and to possibly avoid a service call.
Homes with a few extra items.
Not using the Rapid ...Liquid detergent on some models) to change water hardness to washer drum before starting a cycle.
Touch WATER HARDNESS (on door... hot water wash.
Incorrect dispenser operation
Clogged dispensers or laundry products dispensing too soon.
Make sure your load.
This...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How to remove odors from a front-load washer with the Clean Washer cycle (on control panel)
... tablet will turn off the washer. If an error code, ("rL" or "F-34") is soil that the Affresh cleaner removed from your washer. Repeat the cleaning procedure monthly. Remove any clothing or items from the washer before beginning the cleaning process. Do not add detergent or other laundry products to this cycle. Adding... -
Warm or hot wash temperatures are cooler than I expect - Top-load washer
... to control the amount of energy usage, you replaced. One way to save energy. Front-load washer Vibration - Top-load washer Why are the Warm or Hot wash temperatures cooler than the washer you will notice more cold water with hot. Your new washer uses a temperature control switch to acceptable adult bath-water temperature... -
Hot water fills slowly - Top-load washers
.... NOTE: Both hot and cold water must be connected to save energy is normal. Washer fills slowly - Top-load washer Washer will look smaller than I expect - This valve will not properly operate with agitator. One way to the washer and turned on water and check for tips on the water. Is the water inlet...
Similar Questions
Did Your Machine Show A F8 E1 Error Code Along With The Locked Door?
(Posted by davidwondell 7 years ago)
Maytag Centennial Washer Doesn't Spin How To Fix
(Posted by bjlworadian 9 years ago)
What Does The Error 3e On Maytag Wshing Machine Mean
(Posted by corMi 9 years ago)
