Alcatel OS6850-48L Support and Manuals
Get Help and Manuals for this Alcatel item
View All Support Options Below
Free Alcatel OS6850-48L manuals!
Problems with Alcatel OS6850-48L?
Ask a Question
Free Alcatel OS6850-48L manuals!
Problems with Alcatel OS6850-48L?
Ask a Question
Most Recent Alcatel OS6850-48L Questions
I Am Unable To Connect Alcatel 918n To Sony Ericsson W150.
I HAVE ENABLED BLUETOOTH IN BOTH MOBILES.I AM GETTING THE MESSAGE "PAIRED BUT NOT CONNECTED". UNABLE...
I HAVE ENABLED BLUETOOTH IN BOTH MOBILES.I AM GETTING THE MESSAGE "PAIRED BUT NOT CONNECTED". UNABLE...
(Posted by subramanians 11 years ago)
Popular Alcatel OS6850-48L Manual Pages
Getting Started Guide - Page 3
...Requirements 8 Electrical Requirements 8 Weight Considerations 8 OS6800-24 8 OS6800-48 8 OS6800-U24 9 OS6800-24L 9 OS6800-48L 9
Items Included 9
October 2006
Unpacking and Initial Setup 10 Unpacking the Chassis 10 Recommendations 10 Instructions 10
Setting Up the Switch 11 Airflow Considerations 11 Installation Options 11 Installing the Switch on a Tabletop or Bench . .11 Tabletop...
Getting Started Guide - Page 8
... to the OmniSwitch 6800 Series Hardware Users Guide.
2 OmniSwitch 6800 Series
October 2006 Twentyfour 10/100/1000 ports are added for each OS6800-48.
They are designed to 384 ports.
Network Applications
Whether operating as a single switch or as a stack. This provides a virtual chassis with a 10/100/1000 capacity of service (QoS) for the OS6800-U24...
Getting Started Guide - Page 12
... Gigabit expansion module cannot be hot swapped. See the OmniSwitch 6800 Series Hardware Users Guide for the expansion module is located at the rear panel of the switch and may interrupt network data flow. Backup Power Supply
OmniSwitch 6800 Series switches support optional backup power supply components. Attempting to take on the full power load...
Getting Started Guide - Page 15
... 6800 Series Hardware Users Guide OmniSwitch CLI Reference Guide OmniSwitch 6800/6850/9000 Switch Management Guide OmniSwitch 6800/6850/9000 Network Configuration Guide
OmniSwitch 6800/6850/9000 Advanced Routing Configuration Guide
Depending on the items ordered for your specific network requirements, the following optional items may also be included:
• Stacking cables (per order)
•...
Getting Started Guide - Page 16
... Gigabit expansion module bays. Alcatel provides factory-installed blank cover plates for the remaining switches that are ready to the location where it will make up the stack. 6 Once all unpacking recommendations and instructions carefully before beginning. Recommendations
• Unpack your order, Small Form-Factor Pluggables (SFPs), stacking cables, and backup power supply components...
Getting Started Guide - Page 17
...
22
24
17 15
24 LINK/ACT 24
22
13
22
20
18
16
14
Front. 6 inches minimum at front of chassis for adequate chassis airflow and access to the OmniSwitch 6800 Series Hardware Users Guide.
Installing the Switch on a Tabletop or Bench." Place your switch is not required at the rear of the chassis. Setting Up the Switch
Note...
Getting Started Guide - Page 20
.... These combo ports support hot-swappable fiber Small Form-Factor Pluggables (SFPs). Be sure that all switches in the OmniSwitch 6800/6850/9000 Network Configuration Guide for all switches in a rack to place all required stacking cables will ensure that all screws are securely tightened.
8 If you are installing multiple switches in the stack. For instructions on the front panel...
Getting Started Guide - Page 21
... pattern. Connector Top
When orienting the stacking cable connector, be sure to the stacking cables installed between adjacent switch, the top-most switch and bottom-most switch in the chassis' stacking port.
However, it is facing up .
Completing a Stacked Configuration 15
Refer to the OmniSwitch 6800 Series Hardware Users Guide. The wide portion of the connector...
Getting Started Guide - Page 22
...For additional supported cabling patterns, refer to the OmniSwitch 6800 Series Hardware Users Guide.
5 To provide added resiliency and redundancy, you must install the redundant stacking cable to the bottom switch. Connect the
redundant cable now. 4 Repeat this procedure until all switches in the stack are connected (see illustrations a, b, and c below shows one supported stacking cable pattern...
Getting Started Guide - Page 23
6 Once all stacking cable connectors are connected, the next step is to connect all switches in the stack are inserted, tighten
the captive screws at the left- Be sure not to "Connections and Cabling" on page 18 for more information. Tightening Stacking Connector Captive Screws 7 Now that all required network and management cables. and right-hand sides of...
Getting Started Guide - Page 24
... a serial connection to the switch and is properly set up and all required hardware components are installed, you should be connected to the OmniSwitch 6800 Series Hardware Users Guide.
18 Connections and Cabling
October 2006 For information on page 20 for more information.
Refer to "Booting Stacked Configurations" on modifying these settings, refer to primary management module...
Getting Started Guide - Page 26
... in the OmniSwitch 6800 Series Hardware Users Guide. Allow a few moments for
switches operating in the stack. ondary, and idle roles is to manually power on the stack.
Booting Stacked Configurations
Once the switches have been attached, the next step is provided in the stack to "OmniSwitch 6800 Series Rear Panel" on the switch's front panel. For more information. Important...
Getting Started Guide - Page 30
... the switch can support any remote login sessions, a valid IP address must be configured. For example:
-> ip interface remote address 172.22.120.1 vlan 1
24 Your First Login Session
October 2006
registered in the setup process. Assigning an IP Address to the Switch or Stack
Assigning an IP address to your OmniSwitch 6800/ 6850/9000 Switch Management Guide...
Getting Started Guide - Page 31
... by the user. All other switches in the stack.
For more information on OmniSwitch 6800 Series switches. As a result, users who know the correct user login and password will exist on the stack's primary switch
You are not required to manually assign the IP address to each switch in the stack whenever either of your OmniSwitch 6800/ 6850/9000 Switch Management Guide. This way...
Getting Started Guide - Page 66
... Users Guide
Complete technical specifications and procedures for all OmniSwitch 6800 Series hardware, including chassis, power supplies, fans, combo ports, stacking procedures, optional backup power supplies, etc.
• OmniSwitch CLI Reference Guide
Complete reference to -MIB variable mappings.
• OmniSwitch 6800/6850/9000 Switch Management Guide
Includes procedures for readying a switch...
Alcatel OS6850-48L Reviews
We have not received any reviews for Alcatel yet.