Campbell Scientific CS506 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CS506 manuals!
Problems with Campbell Scientific CS506?
Ask a Question
Free Campbell Scientific CS506 manuals!
Problems with Campbell Scientific CS506?
Ask a Question
Popular Campbell Scientific CS506 Manual Pages
CS506 Fuel Moisture Sensor - Page 3
... nature, or shipping damage. Campbell's obligation under normal use and service for installation services performed by Campbell such as programming to customer specifications, electrical connections to products manufactured by Campbell Scientific, Inc. ("Campbell") to be the sole and exclusive remedy under this warranty is part of shipment unless otherwise specified in lieu of removing...
CS506 Fuel Moisture Sensor - Page 4
... site at the customer's expense. Campbell Scientific reserves the right to refuse service on the outside of the problem, an RMA number will be issued. Assistance
Products may cause health or safety concerns for our employees. directly. Affiliate companies handle repairs for customers within three days of Product Cleanliness and Decontamination" form and...
CS506 Fuel Moisture Sensor - Page 5
... links to the printed version of the 26817 fuel moisture/temperature mounting stake.......4
Tables
4-1. Wiring 4 5. CS506 Wiring 4 5-1. Installation 2 4. over duff layer 3
3-2. CS506 Table of Contents
PDF viewers: These page numbers refer to specific sections.
1. mount ~12-in. General Description 1 2. Back view of the 26817 fuel moisture/temperature mounting stake; Datalogger...
CS506 Fuel Moisture Sensor - Page 7
... The CS506 sensor incorporates the same carefully selected USFS standard ponderosa dowels as a wave guide. Second, the dowels are sorted after a 50-minute soak by density to improve ...stainless steel strips pressed into groves in a waterproof epoxy housing. Specifications
The fuel moisture sensor consists of overall measurement error is similar to the same conditions as a sensor. The ...
CS506 Fuel Moisture Sensor - Page 8
... all
range
measurements
0 to 10%
±1.25%
10 to 20%
±2.00%
20 to 30%
±3.40%
30 to 50%
±4.11%
Range:
0-50%
rms error ±0.74% ±0.90% ±1.94% ±2.27%
Power Supply: 5 VDC minimum to 18 VDC maximum
Enable voltage: off at 0 V (4 VDC maximum 18 VDC)
Current...
CS506 Fuel Moisture Sensor - Page 11
... - 73.7974
where θ is the percent of the output signal in microseconds. The CRBasic instruction PeriodAvg is period average in microseconds on .
Datalogger Programming
This section is off. Since fuel moisture does...12 V G SE1 C1
CR10X 12 V G SE1 C1 G
5 For Edlog dataloggers, instruction P27 Period Average may be created using one equation to measure the period of water by ...
CS506 Fuel Moisture Sensor - Page 12
...(PA_uS,1,mV250,1,0,0,100,10,1,0) PortSet (1,0) If PA_uS CS506 Fuel Moisture Sensor
5.1 CR1000 Programming
The following program measures a CS506 fuel moisture sensor using the CRBasic PeriodAvg() instruction.
CS506 Fuel Moisture Sensor - Page 13
of Cycles
5: 1
Timeout (0.01 sec units)
6: 1
Loc [ PA_uS ]
7: 1
Multiplier
8: 0
Offset
4: Do (P86) 1: 51
Set Port 1 Low
5: If (XF) (P89)
1: 1
X Loc [ PA_uS ]
2: 4
<
3: 17.701
F
4: 30
Then Do... (Seconds --) into a
2: 60
Interval (same units as above)
3: 30
Then Do
2: Do (P86) 1: 41
Set Port 1 High
3: Period Average (SE) (P27)
1: 1
Reps
2: 4
200 kHz Max Freq @ 2 V Peak...
CS506 Fuel Moisture Sensor - Page 14
... be changed at least once a year with the new dowel rod. Tighten the screws after replacing the element.
8 CS506 Fuel Moisture Sensor
8: Polynomial (P55)
1: 1
Reps
2: 1
X Loc [ PA_uS...)
1: 0
Minutes (Seconds --) into a
2: 60
Interval (same units as above)
3: 10
Set Output Flag High (Flag 0)
12: Set Active Storage Area (P80)^18555
1: 1
Final Storage Area 1
2: 60
Array ID
13: Real ...
Campbell Scientific CS506 Reviews
We have not received any reviews for Campbell Scientific yet.