Clifford PrimeStart 650 Support and Manuals
Get Help and Manuals for this Clifford item
View All Support Options Below
Free Clifford PrimeStart 650 manuals!
Problems with Clifford PrimeStart 650?
Ask a Question
Free Clifford PrimeStart 650 manuals!
Problems with Clifford PrimeStart 650?
Ask a Question
Popular Clifford PrimeStart 650 Manual Pages
Owners Guide - Page 3
Table of Contents
Important Information 2 Recommended Installation Tools 2 Recommended Procedures 2 Wiring Diagrams 3 Pin Connectors 6
Installation Procedures 8 Control Unit 8 RangeMaster™ Super Heterodyne Receiver Module 8 Wireloom 8 LED Indicator 9 Valet Switch 9 Zone2&#... Table for System Features 25 Programming Table for Remote Controls 26
1
PrimeStart 650 Installation Manual
Owners Guide - Page 4
...clamps without the express approval of Prime Security, Inc. Before installing, discuss the placement of the FCC rules.
This device complies with Part 15 of the LED indicator and valet switch with the vehicle... unit directly to operate this equipment.
2
PrimeStart 650 Installation Manual Turn off dome light or remove dome light fuse to the system without detaching the clamp.
7....
Owners Guide - Page 5
Main Wiring Diagram - 16 Pin
3
PrimeStart 650 Installation Manual
Owners Guide - Page 10
...install a snap
grommet.
8
PrimeStart 650 Installation Manual
Fasten the antenna to
securely fasten the control unit. 2. Plug the wirelooms securely into the control unit WHITE
plug. 2. If an existing grommet is facing downward. Do not mount the control unit near moving parts. 4. Route wires from the vents. 5. Route the antenna cable behind the driver...the end of service. Separate the ...
Owners Guide - Page 11
...sensor harness to the steering column housing or steering column support bracket. LED Indicator 1.
Choose a location for the ... plug. Additional Sensor Input The ORANGE wire is armed.
9
PrimeStart 650 Installation Manual Choose a location that requires a (-) output when the alarm ...pin connector. 2. DO NOT mount the sensor near moving parts or in the direct path of the vehicle. 3. Using...
Owners Guide - Page 12
... monitors the brake light to prevent an unauthorized driver from driving the car and to switch to normal engine operating condition. Set the parking brake. 2. If the parking lights...to "Reverse." 3.
Turn the ignition key to the vehicle's reverse light wire.
10
PrimeStart 650 Installation Manual Parking Lights 1. Brake Lights (Mandatory)
I CAUTION: Some vehicles allow you press the brake...
Owners Guide - Page 14
... will rest at the ignition switch wire harness.
(Continued on next page)
12
PrimeStart 650 Installation Manual If only one of the satellite module 14 ga wires. A few vehicle disarm ...30-amp relays. Accessory Remote Start (-) Input The BLUE/ORANGE wire will show ground only
when the driver door key cylinder is held in the unlock position. Make all wire connections at a neutral state while ...
Owners Guide - Page 15
If additional heater/AC wires are required to installing the starter system. 1. Cut this wire in half. Starter
I WARNING: Review the "...turn the blower switch on . 3. Connect the VIOLET wire to the ignition switch side of the starter wire.
13
PrimeStart 650 Installation Manual Most vehicles have the correct wire. 3. If it will not crank, you have only one onboard 30-amp relay...
Owners Guide - Page 16
... complete remote start wire connection cannot be additional vehicles with the combined neutral safety switch that require the additional relay.
14
PrimeStart 650 Installation Manual There are basically two types of the ignition switch to the neutral safety switch and then to the starter solenoid. A small group of are between ...
Owners Guide - Page 17
...have any questions, please contact the Prime Technical Support Department.
15
PrimeStart 650 Installation Manual If the vehicle starter does not engage, no ... down) the remote start regardless of the make and model of the vehicle
Test Procedure
I CAUTION: Be sure ...shown in the ignition and the driver's door is in the diagram. 7. The wire color codes are required. Activate the remote ...
Owners Guide - Page 19
Door Lock/Unlock The system has onboard door lock relays to lock and unlock all of the doors as well as a two-stage unlock. The diagrams on pages 17-20 will illustrate standard lock/unlock and two-stage unlock.
17
PrimeStart 650 Installation Manual
Owners Guide - Page 23
...The following procedure for tach color code and location information. 1. Use ...PrimeStart 650 Installation Manual Drill a 5/16" mounting hole. 5. If the tach wire is opened . 1. Start the vehicle. If the vehicle is in the remote start will make , model and year. Connect the TAN wire to the vehicle tach wire. Contact Prime Technical Support Department for proper hood clearance. 3. Set...
Owners Guide - Page 24
...the BLACK wire to the alarm module VIOLET wire. 5. Install the 5 amp fuse in the 10 ga RED wire fuse assemblies.
22
PrimeStart 650 Installation Manual Choose a location in the engine compartment away from below...the siren and siren wires cannot be seen or reached from high heat engine
components, moving parts and direct exposure to the other ends of a supplied 20 amp fuse assembly.
2. Connect...
Owners Guide - Page 26
... Valet Mode indicated by turning the ignition key to confirm that you have changed the setting of chirps associated with that feature. 7. Continue flicking the switch on and off, ...on and off. The siren will chirp once each time you wish to program.
24
PrimeStart 650 Installation Manual NOTE: Stop when you wish to program from Protected Valet Mode. Remove the system from ...
Owners Guide - Page 27
...second. Wait 3 seconds, the siren will chirp once for OFF, twice for ON.
25
PrimeStart 650 Installation Manual Wait 3 seconds, the siren will chirp once for 3 seconds, twice for Ignition-Controlled
Door...Controlled
Starting -7°F (-20°C) or -22°F (-30°C)
Security Start Locks™
Factory Setting Passive
OFF ON ON 30 1 Pulse
1 Second
ON 0
Seconds OFF ON - 20 2
Seconds
OFF
...
Clifford PrimeStart 650 Reviews
We have not received any reviews for Clifford yet.