Cub Cadet 3X 26 inch Support and Manuals
Get Help and Manuals for this Cub Cadet item
View All Support Options Below
Free Cub Cadet 3X 26 inch manuals!
Problems with Cub Cadet 3X 26 inch?
Ask a Question
Free Cub Cadet 3X 26 inch manuals!
Problems with Cub Cadet 3X 26 inch?
Ask a Question
Popular Cub Cadet 3X 26 inch Manual Pages
Operation Manual - Page 1
... INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. NOTE: This Operator's Manual covers several models.
Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting
Operator's Manual
Snow Thrower
2-Stage and 3-Stage (300, 500, 600 & 800 Series)
Table of Contents
Safe Operation Practices 2 Assembly & Set-Up 5 Controls & Operation 18
Product Care 23 Parts...
Operation Manual - Page 3
... and remain behind and use your snow-throwing pattern to a complete stop the engine. "Use of engine governor. Replace if necessary.
13.
Do not operate on slippery surfaces. SHUT THE ENGINE OFF!
2.
Do not change the engine governor setting or over-speed the engine. Maintain or replace safety and instruction labels, as a water heater, furnace...
Operation Manual - Page 5
... www.opei. Review this product. Contents of printing. It instructs you for various models.
If applicable, the power testing information used to establish the power rating of product specifications for purchasing this manual frequently to provide excellent performance when properly operated and maintained.
Assembly & Set-Up
2
Thank You
Thank you how to safely and easily...
Operation Manual - Page 11
... way into pinion gear. See Figure 2-28. See Figure 2-30. Support rear of the chute directional control rod.
2.
Figure 2-26
1. Insert chute control rod into chute control head as far into chute...(d) and bow-tie cotter pin (e) from chute support bracket. Place chute onto chute base and ensure chute control rod is positioned under handle panel. Install hex screw (c) removed in Step 1, but do ...
Operation Manual - Page 12
...assembly. See Figure 2-36.
3. See Figure 2-37.
(a)
(b)
Figure 2-37
12
Section 2 - Refer to Set-Up (page 14)
Figure 2-34
1. 7. Overhead Chute Control (w/ Flex Shaft & Steel Chute)
(a)
Figure ... (a) removed in Step 1. STOP
Continue to Service section for Chute Control Rod adjustments.
8.
Secure chute control head to chute support bracket with wing nut (b), clevis pin (d), and...
Operation Manual - Page 14
...through the wire guide below the chute control head.
NOTE: For smoothest operation, cables should all be to Service section for manual movement of chute...Set-Up (page 14)
The E-Z Chute™ does not require any installation. Chute control cables are routed through a single wire guide (a) on top of the engine and/ or through the wire guides will depend on page 18.
Locate cable guide...
Operation Manual - Page 15
... wing knob. On units with manual chute tilt, including E-Z Chute™, the distance snow is fastened to the top of...Cutters (If Equipped)
The drift cutters are mounted inverted at the factory set roughly 1/8" below the shave plate. See Figure 2-52.
(b) (a)
...
Chute Assembly
NOTE: For models with 2-Way/4-Way or Electric Chute Directional Control and/or models with carriage bolts (a) and...
Operation Manual - Page 16
...Manual...57.
8. On E-Z Chute™ models, loosen the rear hex screw on ...Reinstall and tighten the carriage bolts (b) and hex nuts (c) all instructions below. Refer to stop before releasing auger control lever. Confirm that ...shown in position for ALL moving parts to Controls & Operation section (page... In a well-ventilated area, start the snow thrower engine.
Do not attempt to front ...
Operation Manual - Page 17
...& Oil
Refer to Figure 2-60 inset.
5. Assembly & Set-Up
17 Retighten upper hex screw. 5. If necessary repeat Steps 2-4 to the Engine
Operator's Manual. 2.
Figure 2-61
4. NOTE: If excessive slack is ...tests failed, the drive cable is released and in need of adjustment. 1. Drive Control (Models with out Hydro Transmission) (If Equipped)
NOTE: Drive control on shift rod and pull it...
Operation Manual - Page 19
...follow all instructions carefully and perform all adjustments to cover the vent hole when pushing, forces fuel directly into the auger housing. Not all snow thrower models and the snow thrower ... engaged, the augers rotate and draw snow into the engine's carburetor to aid in this manual are applicable to your Engine Operator's Manual for normal snow conditions. Headlight (Single or Double) ...
Operation Manual - Page 20
...Refer to disengage the augers.
Figure 3-5
*On select models, the drive control lever also locks the auger control lever... and the augers will result in the Assembly & Set-Up section prior to disengage the drive.
2-Way Chute...snow thrower in which snow is thrown, squeeze button on the left side of the upper handle, the drive control bail is used to the left. Read and follow all instructions...
Operation Manual - Page 23
... Manual. Engine running on select models) have two wear edges. Stale fuel.
• Fill tank with clean-out tool. Carburetor out of Blowing It
1. Engine over-governed.
• Contact an authorized Service Center. Excessive Vibration
1. Check for information regarding tire pressure. Repair as instructed in CHOKE position.
• Move choke to RUN position. If the problem...
Operation Manual - Page 25
...instructions on adjusting chute assembly/E-Z Chute™. Service
Auger Belt Replacement (500, 600 and 800 Series)
To remove and replace... auger belt, proceed as follows: 1. Remove plastic belt cover on adjusting shift rod.
Figure 4-10 NOTE: On models...If chute fails to Assembly & Set-up with second hole in &#...
Operation Manual - Page 26
... run until it aside and save.
(a)
(c)
(b)
Figure 4-15 4. Remove the belt.
7. Replace auger belt by following instructions in Assembly & Set-Up section (page 16). Drive Belt Replacement (500, 600 and 800 Series)
NOTE: See your authorized service dealer to prevent accidental starting.
3. Drive Belt Replacement (300 Series)
1. Remove the auger belt as a belt keeper and unhook...
Operation Manual - Page 27
... serviceable.
See Figure 4-20.
See Figure 4-22. Perform Drive Control Lever test shown on the snow thrower
10. Tighten each screw only one rotation before carefully sliding friction wheel assembly off shaft. Section 4 - Reinstall the flange lock nut. Reassemble the belt cover on page 17.
Follow the instructions below. Do not attempt to replace...
Cub Cadet 3X 26 inch Reviews
We have not received any reviews for Cub Cadet yet.