Dynex DX-HTVMM1703-C Support and Manuals
Get Help and Manuals for this Dynex item
This item is in your list!
View All Support Options Below
Free Dynex DX-HTVMM1703-C manuals!
Problems with Dynex DX-HTVMM1703-C?
Ask a Question
Free Dynex DX-HTVMM1703-C manuals!
Problems with Dynex DX-HTVMM1703-C?
Ask a Question
Popular Dynex DX-HTVMM1703-C Manual Pages
User Guide - Page 1
Full Motion Mount for TVs 47" - 70"
DX-HTVMM1703-C
For VESA patterns: • 7.9 × 7.9" (200 × 200 mm) • 11.8 × 7.9" (300 × 200 mm) • 11.8 × 11...215; 15.7" (500 × 400 mm) • 23.6 × 15.7" (600 × 400 mm)
For wood-stud or concrete wall installations
USER GUIDE
Before using your new product, please read these instructions to prevent any damage.
User Guide - Page 2
... for TVs 47" - 70"
Safety information and specifications
IMPORTANT SAFETY INSTRUCTIONS - The wall must not exceed 99 lbs. (45 kg). 2 DX-HTVMM1703-C
Full Motion Mount for damage or injury caused by Dynex. to 70 in . Keep these directions, or have doubts about the safety of the installation, contact Customer Service or call :
1-800-305-2204
18.1 in...
User Guide - Page 3
3 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
Tools needed
You will need the following tools to assemble your new TV wall mount:
Phillips screwdriver
Edge-...
User Guide - Page 4
4 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
TV Hardware Bag
Label A1 A2 A3
Hardware M4 × 12 mm screw
M4 × 30 mm screw ...
User Guide - Page 5
... part of the back of your TV. Determine whether your TV has a flat back or an irregular or obstructed back
1 Carefully place your TV screen face-down on the back of your TV. You do not block any jacks. 5 DX-HTVMM1703-C
Full Motion Mount for instructions....top stand attached, remove the stand. See the documentation that came with your TV for TVs 47" - 70"
Installation instructions
STEP 1 -
User Guide - Page 6
... or obstructed TV back, also use M4 or M5 screws, select the M 4/M5 washer (A12) or if you encounter resistance, stop immediately and contact customer service. 6 DX-HTVMM1703-C
Full Motion Mount for your TV. Option 2: Attaching the mounting hardware to TVs with an irregular/obstructed back: M4 X 30 mm screws (A2) M5 X 30...
User Guide - Page 7
... the TV. 3 Tighten the screws until they are snug against the TV brackets.
Do not over tighten. 7 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 3 - A12 or A13 A1/A3/ A5 or A8...
TV brackets (2)
Magnetic removable bubble level
Phillips screwdriver Make sure that the brackets are level. 2 Install washers (A12 or A13) and screws (A1, A3, A5, or A8) into the holes in the back of the...
User Guide - Page 8
... (4) or
or
A4 (4) or
A6 (4)
A7 (4)
or
or
or
A9 (4)
A10 (4)
Washers or
A12 (4)
A13 (4)
Spacers
A11 (4)
TV brackets (2)
Magnetic removable bubble level
Phillips screwdriver 8 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 3 -
User Guide - Page 9
... the middle of the wall plate on the back of the TV should also be offset .8 in the wall:
1 Measure the distance from the ground. 9 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 4 - Before you drill holes in . Keep in . This is b.
3 Add a + b. This measurement is normally 40 to the...
User Guide - Page 10
Make sure that the template is level. 10 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 5 - CAUTION: DO NOT over-tighten the lag bolts (B1).
*...edge stud
finder
Magnetic removable bubble level
Drill
Socket wrench
3/16 in . (16 mm).
1 Locate the stud. Option 1: Installing on the wall mount with the pilot holes, insert the lag bolts (B1) through the lag bolt washers (B3), then...
User Guide - Page 11
...concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm). * Minimum horizontal spacing between blocks. 11 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 5 - Concrete wall
3/8 in. (10 mm)
Magnetic removable bubble level...level. Make sure that the anchors are firm against the wall plate. Option 2: Installing on the wall mount with the anchors, insert the lag bolts (B1) through ...
User Guide - Page 12
... securely locked onto the wall plate. You will need
Phillips screwdriver HEAVY! Safety bolt
You'll need assistance with a Phillips screw driver.
CAUTION: Do not release the TV until the safety bolts click into place, then tighten the bolts with this step. 12 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 6 -
User Guide - Page 13
Popper button
Cables
13 DX-HTVMM1703-C
Full Motion Mount for attached devices along the mounting arm, then snap the popper buttons over the cables to hold them in place. Manage cables
• Thread cables for TVs 47" - 70"
STEP 7 -
User Guide - Page 14
... side. 3 To tilt of the TV up or down, hold the top and bottom of the TV, then tilt the TV forward or backward. 14 DX-HTVMM1703-C
Full Motion Mount for TVs 47" - 70"
STEP 8 -
User Guide - Page 15
... China
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. 1-800-305-2204 www.dynexproducts.com DYNEX is printed on the web site. 15 DX-HTVMM1703...
Dynex DX-HTVMM1703-C Reviews
Do you have an experience with the Dynex DX-HTVMM1703-C that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dynex yet.
Earn 750 points for your review!