Fluke 726/FPC Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 726/FPC manuals!
Problems with Fluke 726/FPC?
Ask a Question
Free Fluke 726/FPC manuals!
Problems with Fluke 726/FPC?
Ask a Question
Popular Fluke 726/FPC Manual Pages
Product Manual - Page 1
All product names are trademarks of their respective companies.
®
726
Multifunction Process Calibrator
Users Manual
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 All rights reserved. September 2005
© 2005 Fluke Corporation.
Product Manual - Page 2
... which is returned to that service center, with its functional specifications for 90 days and that software will be error free or operate without interruption. The warranty period is three years and begins on non-defective media. Parts, product repairs, and services are warranted for repair in one country is purchased through a Fluke authorized sales outlet or Buyer...
Product Manual - Page 4
to 20 mA 30 Simulating a 4- 726 Users Manual
HART Resistor ON/OFF 16 Getting Started ...16
Voltage ...38 Setting 0 % and 100 % Output Parameters 41 % Error Functionality 41 Stepping and Ramping the Output 41 Manually Stepping the mA Output 42 Auto Ramping the Output 42 Storing and Recalling Setups 42 Store a Setup ...42 Recall a Setup ...43
ii
MyFlukeStore Shop for Fluke products ...
Product Manual - Page 6
726 Users Manual
Index
Loop Power Supply 64 Pulse Read and Pulse Source 64 Pressure Measurement 64 General Specifications 65
iv
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 10
...physical parameters. See Table 1.
Multifunction Process Calibrator
Introduction
The Fluke 726 Multifunction Process Calibrator (referred to measure and source volts, ...setups. • Manual and automatic stepping and ramping.
• Stores and recalls calibration screens. • Control the Calibrator remotely from a PC running a
terminal emulator program.
1
MyFlukeStore Shop for Fluke...
Product Manual - Page 13
...test leads, disconnect the live test lead. 726 Users Manual
XW Warning
To avoid possible electric shock ...use the Calibrator if it operates abnormally. Replace damaged test leads before connecting the live test...serviced.
• Do not operate the Calibrator around explosive gas, vapor, or dust.
4
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 When in the Users Manual...
Product Manual - Page 15
726 Users Manual
AC72 Alligator Clips
TL75 Test Lead Set
Stackable ...Test Leads
FREQ
TC
RTD
PULSE
CONFIG SELECTION
SAVE RECALL
ENTER
EXIT CONFIG 100%
25%
TRIGGER/STOP
25%
Return to
0%
Recall
mA+SOURCE
/
30V MAX MEASURE
ALL
TERMINALS
3W
V Hz
MEASURE
TC
V mA
mA- RTD
LOOP
4W
COM
COM
Figure 1.
Standard Equipment
bec01f.eps
6
MyFlukeStore Shop for Fluke...
Product Manual - Page 21
... 2-, 3-, and 4-wire selections. 726 Users Manual
Table 4. Moves through MEASURE and... SOURCE modes in the lower display. P
M
Cycles the Calibrator through the configuration menus. Key Functions (cont.)
No
Name
Description
Cycles through the memory locations of Calibrator setups. Inserts a 250 Ω resistor when in 25 % steps
Used for Fluke...
Product Manual - Page 23
...Fluke products online at: www.
.com 1.888.610.7664 Press C until Contst Adjust appears on /off To enter the configuration menus, press C. Press G/EXIT CONFIG to save the setting.
14
726 PRECISION CALIBRATOR
1 3
%Error... S to adjust the contrast up and down. 3. 726 Users Manual
Configuration Menus
Use the configuration menus to set or change these parameters of the Calibrator: • ...
Product Manual - Page 25
... the setting.
Voltage to Voltage Test
To perform a voltage-to
select dc voltage (upper display). Press l to -voltage test:
1. Press and hold G to turn on the Calibrator. Press X to increase the output to change. Connect the Calibrator's voltage output to select dc voltage sourcing. 5. Press Y and Z to select a digit to 5 V. 726 Users Manual...
Product Manual - Page 37
...be applied with specified materials. 726 Users Manual
• Never apply pressure above... pressure. The threads on the pressure module or the pressure module instruction sheet for Fluke products online at: www.
.com 1.888.610.7664 Continue pressing... in Figure 13. Refer to the right of 700PA3 is attached and sets its range accordingly.
3. This can also apply a pressure within range ...
Product Manual - Page 49
Connections for Sourcing Pressure
bec47f.eps
40
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 726 Users Manual
726 PRECISION CALIBRATOR
Measure mA Source Pressure 24 V Loop Power Enabled
Hand Pump
%Error
V mA LOOP
ZERO 3 Seconds
OPEN/CLOSE SWITCH TEST
MEAS SOURCE
HART V mA
TC
RTD
FREQ PULSE
CONFIG SELECTION
SAVE RECALL...
Product Manual - Page 51
... battery condition or a battery change does not jeopardize the stored settings.
When L is pressed, the Calibrator produces a repeating 0 % - 100 % - 0 % ramp in a choice of the display changes to select the desired memory location (at each step. 726 Users Manual
Manually Stepping the mA Output
To manually step current output: • Use H or I to step the current...
Product Manual - Page 52
... 1.888.610.7664 Push S again to recall the setup from the proper memory location. Push S to RECL SETUP.
3. A low battery condition or a battery change...following procedure, refer to change does not jeopardize the stored settings. Push S to store the measurement and return the
unit ...changes to 40 data samples can be recalled for Fluke products online at the top of the display) flashes...
Product Manual - Page 53
....610.7664
726 Users Manual
Memory Locations Save Data Mode Indicator
S A V E D A T A
Data Point
1
bec46f.eps
Figure 19. Push Z to see the next saved measurement, 2 of counts is not relevant.
Push Y or Z to show RECL SETUP and RECALL DATA. 2. The data saved in this mode since ramping or stepping during a pulse train is set the...
Fluke 726/FPC Reviews
Do you have an experience with the Fluke 726/FPC that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!