Harbor Freight Tools 62403 - 6 in. 5.7 Amp Heavy Duty Dual Action Variable Speed Polisher Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 62403 manuals!
Problems with Harbor Freight Tools 62403?
Ask a Question
Free Harbor Freight Tools 62403 manuals!
Problems with Harbor Freight Tools 62403?
Ask a Question
Popular Harbor Freight Tools 62403 Manual Pages
User Manual - Page 1
... and year of this manual and the receipt in any parts are missing or broken,
please call 1-888-866-5797 as soon as possible. Failure to continuing improvements, actual product may not be drawn proportionally. SAVE THIS MANUAL. All rights reserved.
Owner's Manual & Safety Instructions
Save This Manual Keep this manual for assembly and service may differ slightly...
User Manual - Page 2
...Specifications 9 Setup 9 Operation 10
Maintenance 12 Parts List and Diagram 14 Warranty 16
Safety
Setup
Operation
WARNING SYMBOLS AND DEFINITIONS This is used to alert you to your mains-operated (corded) power tool. Save all safety warnings and instructions...
General Power Tool Safety Warnings
Read all warnings and instructions for future reference. Power tools create sparks which ,...
User Manual - Page 3
...area. Do not use a power tool while you are connected and properly used for the specific hazards in a damp location is grounded.
3. A wrench or a key left attached to...Keep your finger on invites accidents.
4. Safety
Setup
Electrical safety
1. Keep proper footing and balance at all times. Never modify the plug in moving parts.
7. Operation
Maintenance
Item 62403
For technical ...
User Manual - Page 4
...are not specifically designed and recommended by a qualified repair person using only identical replacement parts. Use ...instructions, taking into account the working conditions and the work to the maximum speed marked on application, use . Service
Have your application. Read all instructions...for damage or install an undamaged accessory. After inspecting and installing an accessory, ...
User Manual - Page 5
...Setup...arm may make exposed metal parts of work area must be ... harm. If you do this instruction manual cannot cover all possible conditions and...practical ways to secure and support the workpiece to high intensity... contact Harbor Freight Tools for a replacement.
18. Holding the work with...Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.)
25. Prolonged exposure...
User Manual - Page 6
...2. Operation
Maintenance
Page 6
SAVE THESE INSTRUCTIONS. The wheel may cause temporary or ... 1-888-866-5797. Item 62403 Safety
Setup
Kickback and Related Warnings
Kickback is a ...check‑ups to ensure medical problems are taken.
2. Pinching or ... Operations
Do not use this manual. To reduce the risk of...point of work .
7. Safety Warnings Specific for an extended period should not ...
User Manual - Page 7
...the Canadian Standard Association, and the National Electrical Code.
2. The plug must be used in either...Page 7 If damaged, have a proper outlet installed by a service facility before use the tool if the power... will not fit the outlet, have it repaired by a qualified electrician. The green wire ...See Outlets for 2-Prong Plug
1. Safety
Setup
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM...
User Manual - Page 8
...
Setup
Extension Cords
1. Using extension cords with the suffix "W-A" ("W" in good electrical condition. If you must use either a two or three wire extension cord.
2. Make sure the extension cord is acceptable for more than a 16 gauge cord. (See Table A.)
4. Always replace a damaged extension cord or have it repaired by a qualified electrician before set-up...
User Manual - Page 9
...in this manual. The Side Handle may be installed in the ... the parts listed in one hand only or without the Side Handle properly installed.
1....Setup - ASSEMBLY
Installing the Side Handle
TO PREVENT SERIOUS INJURY: Do not operate this product. Tighten securely before set up or use of this tool with one of two positions, on either side of this section.
Safety
Setup
Specifications...
User Manual - Page 10
... or clamps (not included) to prevent movement while working .
5. There must not allow free movement while working.
3. Installing a Threaded Accessory
1. Setup
Operation
Maintenance
Page 10
For technical questions, please call 1-888-866-5797. Safety
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at least 6,400 OPM. • no larger than 6″ (150mm...
User Manual - Page 11
... Allow sufficient time for polishing. Start and stop before setting it down. Allow the tool to come to all ... Remove the Polishing Bonnet from the extension cord.
9.
Polishing Instructions
Safety
Setup
TO PREVENT SERIOUS INJURY: Grip the tool firmly in a ... dirt, oil, grease, etc.
2. Note: The most common error when waxing/polishing a vehicle is free of the vehicle.
15...
User Manual - Page 12
...of this manual must be performed only by a qualified service technician. Release the Trigger to a complete stop .
5. If abnormal noise or vibration occurs, have the problem corrected before setting it must be replaced only by a qualified technician. Operation
Maintenance
Page 12
For technical questions, please call 1-888-866-5797. Safety
Setup
Sanding Instructions
TO PREVENT...
User Manual - Page 13
...service tool.
1. See Extension Cords in .
2.
Motor being reduced by long or small diameter extension cord.
Setup...service. Item 62403
For technical questions, please call 1-888-866-5797. Safety
Troubleshooting
Problem
Tool will not start.
Performance
Carbon brushes worn or damaged. Have qualified technician replace... individually as replacement parts. Accessory damaged...
User Manual - Page 14
...PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 62403 Parts List
Part... Fan Guide Bearing 607 Bushing
Q'ty
1 3 2 6 1 1 3 1 1 1 4 7 1 1 4 1 1 1 1 2 1 1 1 1
Part
25 26...
User Manual - Page 15
Safety
Setup
Assembly Diagram
18 17
45
46
16
19
15
47
20
14
3
21
13
22
23
12
24
11
25
4 2
30 31
26 27
10
32 33
28
9
34
29
8
7
6
5 4
35
3
36
2
37
2
38
1
41 42 43 44
39
40
Operation
Maintenance
Item 62403
For technical questions, please call 1-888-866-5797.
Page 15
Harbor Freight Tools 62403 Reviews
We have not received any reviews for Harbor Freight Tools yet.