Hayward E-Command® 4 Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward E-Command® 4 manuals!
Problems with Hayward E-Command® 4?
Ask a Question
Free Hayward E-Command® 4 manuals!
Problems with Hayward E-Command® 4?
Ask a Question
Popular Hayward E-Command® 4 Manual Pages
Model: ALL MODELS Installation - Page 2
... bus with a continuous copper wire equivalent in size to the grounding means provided in the electric supply service panel with copper conductors not smaller than 8 AWG US / 6 AWG Canada.
• SAVE THESE INSTRUCTIONS WARNING: Disconnect all times.
• A green colored terminal marked "Earth Ground" is provided on this unit to connect a minimum 8 AWG...
Model: ALL MODELS Installation - Page 11
... filter pump relay is off, the relay will not display errors or diagnostics for proper input wiring to the VSC. Two of the Hayward TriStar Variable Speed Control (VSC) includes high voltage input wiring, communication wiring, and menu configuration/settings. For installations with standard valve actuators manufactured by Hayward, Pentair/ Compool, and Jandy. Refer to the diagram on for...
Model: ALL MODELS Installation - Page 15
... the ECOMMAND 4 and the Hayward Tristar Variable Speed Control (VSC). The maximum wiring distance is required, contact the Goldline service dept. The communications cable should be routed away from the ECOMMAND 4 and VSC power connections if possible. VSC Pump Address Setting The VSC address must be used to "2", etc. See page 6 and the diagram below for specific instructions on...
Model: ALL MODELS Installation - Page 17
... the display of a Goldline Aqua Rite or Hayward Swimpure chlorinator), the ECOMMAND 4 will automatically detect and control any Aqua Rite/Swimpure(s) that you navigate through the Configuration Menu and input various information. To access the Configuration Menu
Configuration Menu-Locked
Configuration Menu-Unlocked
Press repeatedly until "Configuration Menu" is enabled (requires the use of...
Model: ALL MODELS Installation - Page 19
... Filter relay is turned on some systems with in the Installation manual for specific information regarding the control logic for variable speed operation Move to next menu item
Freeze Protect
Toggle between Enabled (default) and Disabled Freeze Protection
Enabled
Move to next menu item or previous/next configuration menu
if "Freeze Protect" is enabled
and "1-speed Filter" is...
Model: ALL MODELS Installation - Page 27
... (if applicable) Day and Time
Timers Menu Timeclock and/or Countdown timer settings
Heater Checkout
Follow these instructions to control all desired functions. The ECOMMAND 4 is properly configured to verify that the ECOMMAND 4 is calling for the first time, be sure that the ECOMMAND 4 is properly controlling the heater.
1. 5. Properly rated circuit breakers are installed in the "ON...
Model: ALL MODELS Installation - Page 28
... turning on the main unit keypad. This will automatically turn all automatic control operation and is operating properly: • Press the "Filter" button once (for 3 hours, then automatically return to the Operation Manual. Push the SERVICE button once more detailed instructions on . see Configuration Menu/Heater Config.) is intended to turn outputs on for heater cooldown...
Model: ALL MODELS Installation - Page 31
... and applies to the original owner only.
Aqua Trol, commercial installations, installations outside of the US and Canada, accessory products and replacement parts are covered under normal use and service for a period of purchase or the nearest Goldline authorized warranty service center.
To obtain warranty service or repair, please contact the place of one (1) year. The warranty is...
Model: ALL MODELS Operation - Page 2
...service panel with a continuous copper wire equivalent in the area of the swimming pool, spa, or hot tub to these terminals with an insulated or bare copper conductor not smaller than 8 AWG US / 6 AWG Canada.
• All field installed...not smaller than 8 AWG US / 6 AWG Canada.
• SAVE THESE INSTRUCTIONS To reduce the risk of 100 degrees Fahrenheit may be
hazardous to the circuit ...
Model: ALL MODELS Operation - Page 16
... to previous/next configuration menu
Pool/Spa Setup Pool and Spa
if "Pool and Spa" is enabled, the ECOMMAND 4 will have no effect. When the chlorinator is selected
Spa - It is installed in increments of 5 minutes, from "Manual On/Off" (0 minutes) to "21:00" (21 hours). Chlor. This setting is set to "Pool and Spa".
Configuration Menu Items
Each item...
Model: ALL MODELS Operation - Page 18
...) Heater 1 Extend
Disabled
Move to previous/next configuration menu
if "Heater1" is enabled and
1-speed filter pump is allowed to the pump. This is selected in the High Speed Settings Menu. Temperature is adjustable from 33ºF - 42ºF (1ºC - 6ºC). 38ºF (3ºC) is controlled by commands sent to run at during freeze protection operation...
Model: ALL MODELS Operation - Page 19
... taken to next menu item or previous/next configuration menu
Solar If the solar control logic is configured for solar logic. During this period the filter pump LED will flash and also a "Heater Cooldown, X:XX remaining" message will be set up to turn on the display. Heater Extend If "Enabled", the filter extend logic keeps the filter...
Model: ALL MODELS Operation - Page 27
... the system into Service or Service-Timed mode by pressing the "Service" button.
If you want to completely disable the automatic operation and operate the system manually, you to disable automatic operation and manually control most of service mode. Troubleshooting and Diagnostic Information
The ECOMMAND 4 provides 2 different tools to aid in troubleshooting any problems that may occur...
Model: ALL MODELS Operation - Page 28
... or Swimpure manual to correct error. Diagnostic Menu
To enter the Diagnostic Menu, press the "Menu" button repeatedly until the display shows "Diagnostic Menu". Possible error messages are secure in the terminal block in which are not met, the chlorinator diagnostic display will , most likely, require replacement. This display will be set greater than one reason, in the ECOMMAND 4 main...
Model: ALL MODELS Operation - Page 31
... manual(s).
4. The warranty is not provided, the manufacturing date code will be free of God. Damage resulting from the initial date of purchase or the nearest Goldline authorized warranty service center. To obtain warranty service or repair, please contact the place of installation on authorized service centers please contact the Hayward/Goldline Technical Service Support Center...
Hayward E-Command® 4 Reviews
We have not received any reviews for Hayward yet.