Hikvision DS-2CD3048G2-LIU Support and Manuals
Get Help and Manuals for this Hikvision item
View All Support Options Below
Free Hikvision DS-2CD3048G2-LIU manuals!
Problems with Hikvision DS-2CD3048G2-LIU?
Ask a Question
Free Hikvision DS-2CD3048G2-LIU manuals!
Problems with Hikvision DS-2CD3048G2-LIU?
Ask a Question
Popular Hikvision DS-2CD3048G2-LIU Manual Pages
Quick Start Guide - Page 11
... wiring of the product cover. A few device components (e.g., electrolytic capacitor) require regular replacement. Contact your dealer or the nearest service center. Time Synchronization Set up device time manually for problems caused by AC mains supply voltage: The equipment must be gained by service persons or by users who have been swallowed or placed inside and outside...
User Manual - Page 13
... 34 5.3.2 Capture Manually ...34 5.3.3 View and Download Picture 35 Chapter 6 Event and Alarm ...36 6.1 Set Motion Detection ...36 6.1.1 Expert Mode ...36 6.1.2 Normal Mode ...37 6.2 Set Video Tampering Alarm 38 6.3 Set Alarm Input ...39 6.4 Set Exception Alarm ...40 6.5 Set Video Quality Diagnosis 40 6.6 Set Audio Exception Detection 41 6.7 Set Defocus Detection ...42 6.8 Set Scene Change...
User Manual - Page 21
... Question
You can go to reset the admin password when access the device via browser. Note When you can set the account security during the recovering operation process.
4 Network Camera User Manual
Operating System
Web Browser
Operation Go to Configuration → Network → Network Service → WebSocket(s) to receive the verification code during the activation.
User Manual - Page 44
For detailed installation, refer to Quick Start
Guide of the device. ● You need to know the correct encryption password of your needs. 5. Go to the device....a Hikvision memory card is detected abnormal. Select the memory card. Steps 1. Click Status Detection to format and set the memory card. Note
If the encryption password is ready for use this memory card, see Set New ...
User Manual - Page 47
...Manual
Mounting Type Select file system protocol according to add a Net HDD. 7. File Path The saving path of the device. Click Test to Configuration → System → System Settings → System Service for embedded multimedia card, is only supported by certain device models...SMB/CIFS is available. 6. Enter user name and password of the network disk. Server Address The IP address ...
User Manual - Page 56
... Start Guide for
setting linkage method. 7. Refer to Set Arming Schedule for setting scheduled time. Make sure the external alarm device is only supported by certain models. Refer to Linkage Method Settings for cable connection.
39 Click Save.
6.3 Set Alarm Input
Alarm signal from the external device triggers the corresponding actions of the current device. Network Camera User Manual...
User Manual - Page 59
... settings, refer to the actual environment. 4.
But the detection accuracy is reduced. 4. Check Enable. 3. Note The function is only supported by certain models. The higher the value is, the more easily the defocus image can trigger the alarm. Note The function is only supported by certain models. Network Camera User Manual
Note The function is only supported...
User Manual - Page 65
... network that the device is connected to should support DHCP (Dynamic Host Configuration Protocol). Route Advertisement The IPv6 address is changed after enabling the function. Network Camera User Manual
Chapter 8 Network Settings
8.1 TCP/IP
TCP/IP settings must be configured simultaneously without conflicting to each other.
Manual You can use SADP to get the device...
User Manual - Page 73
... and other network parameters of routers. For more information, refer to the router user manual.
8.13.3 Set Port Mapping on Router
The following settings are connected to be the same as those on the device. Figure 8-1 Port Mapping on different models of the router. 3. Select the WAN Connection Type. 2.
Click Save. Steps 1. Example When...
User Manual - Page 75
... the settings. Access the camera via SADP Software
This part introduce how to activate the camera before using the service. Enable Hik-Connect Service via web browser. 2. Enter platform access configuration interface.
Note The verification code is required when you add the camera to the troubleshooting. 2. Network Camera User Manual
● Visit https://appstore.hikvision.com/static...
User Manual - Page 81
... models.
64 Manual Settings Check Enable and set Location Upload Interval. Note This function may vary according to Configuration → System → System Settings ...set Location Upload Interval. Enter Configuration → System → System Settings → System Service to external device. Note You should keep the parameters of the device. Network Camera User Manual
9.1.4 Set...
User Manual - Page 86
... list. Select the type of IP address filter. Add Add a new MAC address to IPv4. IP address refers to the list. Check Enable. 3. Click Save.
9.4.2 Set MAC Address Filter
MAC address filter is a tool for access control.
You can access the device. 4.
Edit the IP address filter list. Modify the selected...
User Manual - Page 90
... provide privacy and data integrity between two or more communicating computer applications. Network Camera User Manual
Note ● If you set the reminding day before the expiration day. 1 to 30 days are effective for HTTP(S) and enhanced SDK service. The security risk of device internal information leakage exists when the function is the...
User Manual - Page 96
... Camera User Manual
Figure 10-2 Set Rule 5. If the detection target is used to Linkage Method Settings . 7. For the arming schedule settings, refer to add a rule and set the parameters ...Event and click Next to enable the function. ● For the device supporting HEOP, go to VCA to improve detection accuracy. Set parameters.
Check Enable. 3. Click , click on the live view to ...
User Manual - Page 99
... Next to enable the function. ● For the device supporting HEOP, go to VCA to Set Arming Schedule . For the linkage method settings,
refer to VCA → Set Application → Face Recognition → Rule .
82 Steps 1.
Go to Linkage Method Settings . 7. Note ● For certain device models, you need to enable this function on VCA page...
Hikvision DS-2CD3048G2-LIU Reviews
We have not received any reviews for Hikvision yet.