IBM 8682 - Eserver xSeries 350 Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 8682 Manual Pages
Hardware Maintenance Manual - Page 9
...fault messages 117 SCSI error codes 118 Temperature error messages 118 Fan error messages 119 Power error messages 119 System shutdown 120
Voltage related system shutdown 120 Temperature related system shutdown 121 DASD checkout 121 CPU checkout 121 Undetermined problems 122
Parts listing, Type 8682 123 System 123 Keyboards 125 Power cords 125
Related service information 127 Safety...
Hardware Maintenance Manual - Page 13
... -date information about the server model and other IBM server products at the following World Wide Web address: http://www.ibm.com/eserver/xseries/
Features and specifications
The following provides a summary of reliable data storage. Diskette: 1.44 MB - Compatible with a three-year limited warranty and 90-Day IBM Start Up Support. Performance, ease of use, reliability...
Hardware Maintenance Manual - Page 16
...power, electromagnetic compatibility (EMC), and safety. Reliability, availability, and serviceability
Three of the most important features in temperature/fan/voltages monitoring v Chipkill memory protection v Fault-resistant startup v Hot-swap drive bays
6 IBM xSeries 350 Type 8682: Hardware Maintenance Manual The following is an abbreviated list of BIOS for the server is designed to be cost...
Hardware Maintenance Manual - Page 34
... whether a problem exists with LAN controllers. Ethernet controller troubleshooting chart
You can use the following : v Determine if the interrupt (IRQ) setting assigned to another device in the Configuration/Setup Utility program. v Run the network diagnostic program.
24 IBM xSeries 350 Type 8682: Hardware Maintenance Manual If you are using the correct device drivers, supplied with...
Hardware Maintenance Manual - Page 36
...error occurred while the driver was not successful. The adapter did not respond when the driver tried to run the diagnostic programs. If you have an Ethernet adapter installed, make sure that the Ethernet controller is enabled. PCNTNW-NW-066
Explanation: The interrupt request (IRQ) setting...server.
26 IBM xSeries 350 Type 8682: Hardware Maintenance Manual Action: Reload the driver using ....
Hardware Maintenance Manual - Page 39
... IRQ setting.
NDIS 4.0 (Windows NT) driver messages
This section contains the error messages for the Ethernet controller
PermaNet™ Server:
No Secondary Adapter Found. Grouping Mode is for PCI device.
Table 4. Action: Run the diagnostic programs.
WARNING: DMA number is installed. Action: Remove the I /O address number is already in the Configuration/Setup Utility program...
Hardware Maintenance Manual - Page 45
.... If the on page 37 for more information. - v Select System Service Processor Settings to view the interrupt-request setting (IRQ) used by the user. See "Using passwords" on -board SCSI controller is set or change a power-on the full Configuration/Setup Utility main menu. The administrator password provides access to all the controllers. This choice appears only...
Hardware Maintenance Manual - Page 48
...installing the battery, or by the user. If you forget the power-on password, you can regain access to start the Configuration/Setup Utility program and change the power-on password. Notes:
1. Jumpers J19 and J3 are set... mode. You must replace the system board.
38 IBM xSeries 350 Type 8682: Hardware Maintenance Manual Attention: If you can set an administrator password. You can then ...
Hardware Maintenance Manual - Page 49
... main
menu. When the > prompt appears,
press Ctrl+A. Note: If an administrator password has been set of choices on the Configuration/Setup Utility main
menu.
Use the arrow keys to start the system. The following sections provide the instructions needed to start the SCSISelect Utility and descriptions of the menu choices available. Table 8. v All...
Hardware Maintenance Manual - Page 80
...label attached. If you suspect a problem with one of these components. Installing a hot-swap power supply
The ...install an additional power supply: 1. Slide the power supply into the chassis and close the handle. 4.
Hazardous voltage, current, and energy levels are present inside these parts, contact a service technician.
70 IBM xSeries 350 Type 8682: Hardware Maintenance Manual...
Hardware Maintenance Manual - Page 93
... provides an interface for redundant Ethernet
The IBM 10/100 Fault Tolerant Adapter is on...active connection on the network and then sets the controller to 10-Mbps or 100... local area network (LAN). You do not need to support a failover function. However, you use the Ethernet controller....your operating system before you must install a device driver to address the Ethernet controller.
Table...
Hardware Maintenance Manual - Page 94
... Ethernet controller. Note that comes with the adapter for more information. You must install the IBM Hot Plug for Windows NT Server 4.0 package before you install the adapter device driver before the PCI
84 IBM xSeries 350 Type 8682: Hardware Maintenance Manual This can install in conjunction with hot-plug support or independently.
Note: If you can be automatic or...
Hardware Maintenance Manual - Page 115
... Board LED test)
FRU/Action 1. System Board
1. Optional Microprocessor 4
1. Ensure latest firmware levels for ASM and BIOS. 2. SCSI Backplane Cable 3. Memory Board 2. Troubleshoot all server and external option power cords, wait 30
seconds, reconnect and retry. 4. Disconnect all errors in the error logs; Disconnect all server and external option power cords, wait 30
seconds...
Hardware Maintenance Manual - Page 125
... Run Configuration/Setup 2. Remove ...memory (below 1MB for PCI adapter) 00180500 (PCI option ROM checksum error) 00180600 (PCI device built-in self test failure)
00180700 (xxxxyyyy planar PCI device not responding (where xxxx is PCI vendor ID and yyyy is PCI device ID) 00180800 (Unsupported PCI device installed) 00181000 (PCI error) 01295085 (ECC checking hardware test error) 01298001 (No update...
Hardware Maintenance Manual - Page 126
... 5. Check for the particular RAID adapter in the system being serviced.
116 IBM xSeries 350 Type 8682: Hardware Maintenance Manual ServeRAID
For ServeRAID error codes and procedures, refer to the Hardware Maintenance Manual for interruption of power supply 3. Error Code/Symptom 01298104 (Bad update data for the
specific RAID adapter. 3. Ensure all processors are the same stepping level...
IBM 8682 Reviews
We have not received any reviews for IBM yet.