JET Tools GH-1440W-1 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools GH-1440W-1 manuals!
Problems with JET Tools GH-1440W-1?
Ask a Question
Free JET Tools GH-1440W-1 manuals!
Problems with JET Tools GH-1440W-1?
Ask a Question
Popular JET Tools GH-1440W-1 Manual Pages
User Manual - Page 1
M-321810-1 for service parts and electrical diagrams.
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-321810 Revision G2 11/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operation and Maintenance Instructions
Geared Head Lathes
Models GH-1340W, GH-1440W
See manual no.
User Manual - Page 2
... items that are made specifically for further clarification. Limitations on official JET website are not sold in duration based upon the product. (See chart below .
JET reserves the right to Get Technical Support Please contact Technical Service by JPW Industries, Inc. JET® branded products are given as expendable parts or accessories expected to parts, fittings, and accessory...
User Manual - Page 3
...
Page
1.0 Warranty and service ...2 2.0 Table of contents...3 3.0 Safety warnings...4 4.0 Specifications ...5 5.0 Uncrating ...6
5.1 Contents of shipping container ...6 6.0 Installation ...7
6.1 Chuck preparation ... Tailstock off-set ...17 12.6 Tailstock gibs...17 12.7 Headstock alignment ...18 12.8 Removing gap section...18 12.9 Installing gap section...18 12.10 Belt replacement and adjustment......
User Manual - Page 4
... specifically designed...replacement parts when servicing. 25. Make all machine adjustments or maintenance with all loose clothing and confine long hair. Keep the floor around , carrying on how often you do not use extreme caution and replace the guards immediately. 8. Some examples of scrap material, oil and grease. 7. Use the right tool. Read and understand the entire instruction manual...
User Manual - Page 5
...Specifications
GH-1340W-1
GH-1440W-1
GH-1340W-3
GH-1440W...Feed Rod Diameter (in 3/4 3/4
Compound and Carriage: Toolpost Type 4-Way 4-Way Maximum Tool Size (in 5/8 x 5/8 5/8 x 5/8 Maximum Compound Slide Travel (in 3-1/2 ...specifications were current at the time this manual was published, but because of our policy of continuous improvement, JET reserves the right to change specifications...
User Manual - Page 6
5.0 Uncrating
Open shipping crate and check for Cam Locks 1 Tool Post Wrench 1 Instruction Manual 1 Parts List Manual 1 Warranty Card
Figure 1
6 Missing parts, if any, should be reported to your distributor and shipping agent. Failure to comply may cause serious injury!
5.1 Contents of this manual before attempting set-up or operation. Report any shipping material until the Lathe is ...
User Manual - Page 7
.... 6.0 Installation
1. Finish...service the lathe on an adequate work surface.
3. The leveling pads included in the tool box and the leveling screws in the tool box.
2. Cover all parts... thoroughly with a light film of lathe stand. Close the door.
6.1 Chuck preparation (three jaw)
Read and understand all four sides
4. Support...
User Manual - Page 10
...!
Pour three gallons of the machine. Failure to comply may cause serious injury!
Replace the cover.
Fasten coolant door to stand. If the chuck rotates in coolant pump...switch wire from the tailstock. The GH-1340W-3 & GH-1440W-3 Geared Head Lathes are rated at the tailstock end. To switch from 230V to 460V operation (GH-1340W-3 & GH1440W-3 only)
Disconnect the machine from ...
User Manual - Page 12
To set . Secure the steady rest in position.
3. It prevents flexing of the cutting tool. Controls
1. located on and off.
Press and release to prevent premature wear.
The sliding fingers are required as a support for tuning operations on the saddle and follows the movement of play, but not overly tight. Coolant On-Off Switch...
User Manual - Page 15
...19), depending on feed and thread tables (A, Fig. 18). 1. Setting the gears too tight will be changed. 6. The 30T, 32T, ...there is to the chart.
11.3 Change gears replacement
The 25T, 127T, 50T gears are used ...tool box are installed in place temporarily by tightening nut (A & B, Fig. 19). 5. Move the forward/reverse selector (A, Fig. 20) up or down depending on the left end of this manual...
User Manual - Page 21
M-321810-1 Revision H 11/2014
Copyright © 2014 JET JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-321810 for operation and maintenance instructions.
This .pdf document is bookmarked
Parts List and Electrical Diagrams
Geared Head Lathes
Models GH-1340W, GH-1440W
See manual no.
User Manual - Page 22
... Tool Post and Compound Slide Assembly - Exploded View...27 2.12.2 Bed Assembly - Exploded View 35 2.16.2 Thread Dial Assembly - Parts List ...37 2.18.1 Coolant and Work Light Assembly - Parts List ...7 2.3.1 Headstock Assembly III - Parts List 39 2.19.1 Chuck Guard Assembly - Having the Model Number and Serial Number of Contents ...2 2.0 Replacement Parts...2
2.1.1 Headstock...
User Manual - Page 27
...-18 Gear 31T 1 106 GB1096-10X18 Key 10x18 1 107 GH1440W-04-13 Spline Shaft 1 108 GH1440W-04-24 Cover ...1 109 TS-1503081 Hex Socket Cap Screw M6x35 4 157 11-15 Brake Shoe Assembly 1 164 VB-A73 V-Belt (GH-1340W-1/3 & GH-1440W-1 2 VB-A74 V-Belt (GH-1440W-3 2
7
Description
Size
Qty
56 TS-1503031 Hex Socket Cap Screw M6x12...
User Manual - Page 31
... Cap Screw M8x40 2 13 TS-1504051 Hex Socket Cap Screw M8x25 3 14 GH1440W-14 Pin 5x20 2 15 GH1440W-15 Pin 5x28 2 16 05-75 Plug...2 33 GB118-A8X30 Pin A8x30 2 121 GB867-2X4 Rivet 2x4 4 122 GH-1440W-05-12/1.......... Part No.
2.4.2 Gearbox Assembly I - Parts List
Index No. Speed Chart 1
11 Description
Size
Qty
1 05-73...
User Manual - Page 44
... Pan Head Screw M3x6 2 GHW-THA Tool Post Assy. (includes #1 & 2 1 GH1440W-CPA Compound Assy. (includes # 11-39 for 14 1 GH1340W-CPA Compound Assy. (includes # 11-39 for 13 1
24 Parts List
Index No.
Description
Size
Qty
1 07-32 Tool Post 1 2 GB83-10X50 Tool Lock Screw 10x50 8 3 GH1440W-07-20 Handle Hub 1 4 GH1440W-07-21 Handle Shaft 1 5 GB4141...
JET Tools GH-1440W-1 Reviews
We have not received any reviews for JET Tools yet.