JET Tools J-8201K Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools J-8201K manuals!
Problems with JET Tools J-8201K?
Ask a Question
Free JET Tools J-8201K manuals!
Problems with JET Tools J-8201K?
Ask a Question
JET Tools J-8201K Videos
JET J 8201K 14 Inch 115 Volt Single Phase Vertical MetalWood Bandsaw
Duration: 1:41
Total Views: 979
Duration: 1:41
Total Views: 979
Popular JET Tools J-8201K Manual Pages
User Manual - Page 1
M-414500 Revision C1 03/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
14-inch Vertical Band Saws
Models: J-8201, J-8203, J-8201VS, J-8203VS
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... that you specific legal rights, subject to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of initial purchase when calling. JET reserves the right to provide proof of maintenance. Product Listing with any reason whatsoever. Manual Hoist Accessories;
If a product requires further inspection, the Technical Service representative...
User Manual - Page 3
... Saw Features...8 Setup and Operation ...8
Set-up ...8 Electrical...9
Connecting to 3-phase power ...9 GROUNDING INSTRUCTIONS ...9 Installing Optional Frame Riser ...12 Installing Optional Rip Fence ...12 Operating Controls ...13 START/STOP Switch ...13 Variable Speed Control ...13 Operating Instructions ...13 Saw blades...13 Adjustments ...14 Adjusting Blade Support/Guide Height...14 Adjusting...
User Manual - Page 4
... and understand the Operating Instructions and Parts Manual as well as blades, bits, cutters, and the like. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
7. DON'T FORCE TOOL It will do a job for best results and full benefits from its electrical supply while servicing.
- USE RIGHT TOOL Don't force tool or attachment to...
User Manual - Page 5
..., and any other part that it comes to the following instruction: The installer shall follow local regulations and National Electrical Code, ANSI/NFPA 70 installation requirements.
5 Close the padlock.
4. REDUCE THE RISK OF UNINTENTIONAL STARTING.
ADJUST UPPER BLADE GUIDE TO JUST CLEARWORKPIECE.
25.
B).
3. TURN POWER OFF. Don't leave tool until the blade has stopped.
23...
User Manual - Page 7
... right to 334 SFPM. Specifications
JET's 14-inch Vertical Band Saws are capable of contour cutting, straight cutting and resawing, and these band saws can cut delicate curves in thick or thin stock. Model number J-8201K J-8203K J-8201VS J-8203VS Stock number 414500 414504C 414502 414503
Capacities: Under Guide (in 6 6 6 6 Under Guide with an infinitely variable speed...
User Manual - Page 8
...blade tension and support mechanism adjustment (refer to complete the electrical hookup.
8 Figure 1: Band Saw Features - Prepare for long or heavy stock. Install the applicable fasteners. Connect power to fill the gearbox.)
4. For 3-phase motors, follow the instructions in the base and mark the positions of the saw . The containers have sufficient amount of replaceable parts...
User Manual - Page 10
...-colored rigid ear, lug, and the like the one illustrated in Figure 5B and C, may be used with all local codes and ordinances.
4. Permanently connected tools:
This tool should be installed by qualified service personnel; The temporary adapter should comply with this plug to an outlet having an equipment-grounding conductor.
10 and after reconnection...
User Manual - Page 13
..., such as stainless steel, require the cut can save you time, trouble, and the possibility of dulling and premature discarding of the blade you normally might use of materials. Otherwise, the effect of the blade. Different blade materials and tooth geometry (pitch and set) permit sawing a wide range of the START pushbutton.
Using the correct...
User Manual - Page 15
... time make sure the table is tightened to the desired setting as the knob is parallel with the blade.
5. 4. If the saw must be exactly on the blade
6. Tighten the trunnion attaching bolts. With everything is 90... miter slot to make sure the
15 Adjusting Blade Speed (Models J8201VS/J-8203VS)
See Figure 10. Lock the table lock knobs securely and recheck for various materials.
3.
User Manual - Page 18
... system.
13. Using the micro-adjusting knob, move the lower blade support assembly (Refer to install the blade upside down. After correctly positioning the carbide guide blocks, tighten the set screws securely. Make sure the teeth on the left side of the blade. Also, make sure the blade is possible to Figure 13) forward until they just contact...
User Manual - Page 19
.... 1.
Troubleshooting
Refer to the step-bystep instructions on the branch circuit.
25. Replace the table insert.
22. Plug the electrical cord into power source or close the circuit breaker on blade replacement.
3....on the branch circuit. 19. Adjust the upper carbide blade guides until the level is correctly adjusted. Then tighten the set screws securely.
21. Insert the table pin into a...
User Manual - Page 20
... wheel Drive wheel rubber protectors Drive belts
Reduction gearbox
Blade support bearings Carbide blade guides
Action
Interval
Maintenance
Listen for sound of missing teeth
Whenever operating saw
Replace blade when bent -
replace if damaged or excessively worn
Replace a glazed belt - Watch for signs of lubricant
Monthly
Replace bearing if leakage occurs
Check for cleanliness
Daily...
User Manual - Page 23
Models J-8201 and J-8203
Index No Part No
Description
Size
Qty
1 J-5513834 Closed Stand 1 J-5507565 Closed Stand Assembly w/o Motor 1 2 J-5513835 Door ...Plate 1PH 1 612156 Strain Relief Plate 3PH 1 12 J-5513845 Pulley Cover 1 13 5513846 Knob ...1 15 TS-1523011 Set Screw M6x6 2 16 5784682 Pulley ...1 17 5513859 Key 5x5x40 1 18 TS-1540031 Hex Nut M5 4 19 TS-...
User Manual - Page 26
...33 SB-8MM Steel Ball 8mm 1 34 5783421 Upper Wheel Blade Guard 1 35 5783341 Upper Support Bracket Post 1 36 5783411 Support Bracket 2 37 5783371 Micro Adjustment Nut 2 38 5783321 Upper Spacing Sleeve 2 39 5783391 Carbide Blade Guide 4 40 5783631 Lower Support Bracket Post 1 42 5783591 Bracket Trunnion Support 1 43 5783611 Point...1 44 J-5783451 Table ...1 45 5783471...
JET Tools J-8201K Reviews
We have not received any reviews for JET Tools yet.