Konica Minolta ProJet 660Pro Support and Manuals
Get Help and Manuals for this Konica Minolta item
View All Support Options Below
Free Konica Minolta ProJet 660Pro manuals!
Problems with Konica Minolta ProJet 660Pro?
Ask a Question
Free Konica Minolta ProJet 660Pro manuals!
Problems with Konica Minolta ProJet 660Pro?
Ask a Question
Most Recent Konica Minolta ProJet 660Pro Questions
I Need To Install A Projet660 Tiamat Load Cell Assy
(Posted by camillegibson30 6 months ago)
Popular Konica Minolta ProJet 660Pro Manual Pages
Cube3 User Guide - Page 2
... 3D Printer Properties 4
4 AT A GLANCE 5
5 SPECIFICATIONS AND REQUIREMENTS 6 Weight 6 Software 6 OpenGL Version 6 Windows Requirements 6 MAC OS X Requirements 6 Android 6 iOS 6 Wireless Options 6 USB Mass Storage Device 6 Electrical Requirements 6 Material Storage 6 Dimensions 7
6 UNPACKING AND SETTING UP YOUR CUBE 8 Contents 8 Unpacking and Installing your Cube 8 Initial Setup...
Cube3 User Guide - Page 5
... and it up. With its Terms of Service and Privacy Policy. This document is based on firmware version: v1.07. The 3D Systems logo, 3D Systems, Cube and Cubify are designed to change without notice. Use of the Cubify.com website constitutes acceptance of materials, enjoy the freedom to print in a particular installation.
Operation is connected. -Consult the dealer...
Cube3 User Guide - Page 6
... be instructed to these additional rights. You must contact the 3D Systems' Warranty Hotline for the CubePro 3D printer. This warranty excludes (i) normal consumable or expendable parts (such as Material Cartridges, Print Pads, and Cube Glue), (ii) repairs required during the warranty period because of abnormal use or conditions (such as riots, floods, misuse, neglect or improper service...
Cube3 User Guide - Page 7
... all instructions prior to prevent potential safety problems and ensure
the Cube's appropriate use. Caution: Indicates something may damage the Cube.
THE PRINT JETS BECOME VERY HOT.
WARNING: HAZARDOUS MOVING PARTS. Caution: Indicates a pinch point hazard that could cause loss of data, damage to ensure proper printing and be mindful of print materials, or 3D prints other than 3D Systems...
Cube3 User Guide - Page 8
... printer model and configuration.
3D Systems, Inc.
4 easy to peel off
Cartridge:
1 cartridge prints 13-to two (2) jets*
Maximum Creation Size: 6" x 6" x 6" (152.40 mm x 152.40 mm x 152.40 mm)
Material:
Tough recyclable plastic
Layer Thickness:
.070 mm (70 microns) | .200 mm (200 microns)
Supports:
Fully automated;
3 CUBE 3D PRINTER FEATURES
The print jets heat print materials...
Cube3 User Guide - Page 14
A B
A
3D Systems, Inc.
10 The cable should lock in place. Open the accessories box and unpack the material cartridge(s)*, the USB mass storage device, the power supply and cord, and the bottle of Cube Glue. Connect the power supply cable to the power inlet port (A) on your configuration, you may receive 1 or 2 cartridges with your printer.
9. To...
Cube3 User Guide - Page 21
... tube is tucked under the top of the printer.
17.
NOTE: The print jet will begin to heat. Wait until the dots align. Select the checkmark to continue.
The left cartridge has been installed. Insert the print jet (from the cartridge that will prime melted material into the right print jet opening on top of the...
Cube3 User Guide - Page 30
... continue. Select the checkmark to cool down before continuing.
3D Systems, Inc.
26 NOTE: Once the cartridge has been installed, allow the print jet to complete the procedure. NOTE: As you rotate the print jet, ensure the print jet tube is tucked under the top of the printer.
NOTE: It may become necessary to rotate the cartridge...
Cube3 User Guide - Page 32
... titled Replacing A Material Cartridge for instructions on replacing cartridge. NOTE: If the print file requires ABS material and PLA material is installed, the printer will prompt you to either change the cartridge(s). NOTE: If the file was built with color(s) that match the material type. NOTE: If the print file requires PLA material and ABS material is installed, the printer will...
Cube3 User Guide - Page 35
... raft material, followed by a fine-grade wet and dry sandpaper to achieve a smoother finish. The scraper can be done without a raft, some larger, more complicated parts may differ from the body. Then use fine-grade sandpaper (not included) to finish smoothing the part.
3D Systems, Inc.
31 8 FINISHING YOUR CREATION
REMOVING YOUR CREATION FROM THE PRINT...
Cube3 User Guide - Page 58
... the touchscreen display and select WIFI. Select Settings (B). 3. If the printer is connected to the name of your printer, navigate to that printer. Select the PRINT tab (A). 2. Connecting Cubify To Your Printer Manually 1.
Select Cube Info (C) from the pop out menu. 4. If multiple printers are connected to the Network screen in the Printer Name (D) area, select Enter IP...
Cube3 User Guide - Page 89
... as it moves between the print pad and the left print jet, the gap is installed before attempting to ensure the first layer of the print pad under the left cartridge is correct.
3D Systems, Inc.
85 This can usually be clean and free from print material. Place the gap gauge on the gauge. Manual Gap Adjustment If Auto...
Cube3 User Guide - Page 101
... printed parts to either our USA or Germany location. Cube 3D printers use eco-friendly plastics that comes with each cartridge for each part with near zero waste in the Cubify Sustainability Program.
• Cartridge Recycling: Send your returned plastic parts as a renewable source to manufacture new cartridges, reducing both raw materials consumption and the waste stream.
3D Systems...
Cube3 Quick Start Guide - Page 4
... NOT TOUCH THE PRINT JETS DURING SETUP AND OPERATION. CAUTION: Read and follow all instructions prior to determine when the print jets are cool enough. To ensure safety, please exercise caution when operating your Cube 3D Printer to young children.
observe children closely and intervene as outlined in this document and the Cube User Guide. doing so...
Cube3 Quick Start Guide - Page 18
... the refuse bin.
15 Once the print jet has reached the proper temperature, the printer will begin to continue. 18. NOTE: As you rotate the print jet, ensure the print jet tube is tucked under the top of the printer. Mount a material cartridge on the right side of the printer
and select the checkmark to continue. Select...
Konica Minolta ProJet 660Pro Reviews
We have not received any reviews for Konica Minolta yet.