Makita BFR750Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita BFR750Z manuals!
Problems with Makita BFR750Z?
Ask a Question
Free Makita BFR750Z manuals!
Problems with Makita BFR750Z?
Ask a Question
Popular Makita BFR750Z Manual Pages
Owners Manual - Page 2
.... 11. A wrench or a key left attached to our continuing programme of the power tool may result in the off-position before turning the power tool on invites accidents. 12. Keep children and bystanders away while operating a power tool. ENGLISH
SPECIFICATIONS
Model
BFR540
BFR750
Screw strip
4×25 - 55 (5/32" x 1" x 2-3/16")
4×45 - 75 (5/32" x 1-3/4" x 2-15/16")
No...
Owners Manual - Page 3
... of moving parts, breakage of parts and any other battery packs may
3 Use of children and do not allow persons unfamiliar with water.
Always be extremely hot and could result in the off . ENC007-2
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Any power tool that have the power tool repaired before inserting battery pack. GEB017-1
SPECIFIC SAFETY RULES...
Owners Manual - Page 4
...the label on feeder
box 4. Red part 2. If the cartridge does not slide in loss ... service life.
3. Always insert it all the way until it is not being inserted correctly. See the table below for tool....INSTRUCTIONS. Let a hot battery cartridge cool down before completely
discharged.
Fenestella
008123
2
3
There are 7 positive-lock screw length settings.
Button 3. Installing ...
Owners Manual - Page 5
... set the reversing switch lever to a complete stop . To start the tool, simply pull the switch trigger. For Models BFR540
Number indicated on the label 25 30 35 40 45 50 55
008239
Screw length 25 mm (1") 30 mm (13/16") 35 mm (1-3/8") 40 mm (1-9/16") 45 mm (1-3/4") 50 mm (2") 55 mm (2-3/16")
For Model BFR750...
Owners Manual - Page 6
Reverse button
008128
008286
Folding screw guide
Installing screw strip Insert the screw strip through the feeder box until the first screw reaches the position next to the driving position.
1
1. Feeder box
2. Screw strip
3. Folding the screw guide allows space used for temporarily hooking the tool. Thumb screw
Removing screw strip To remove the screw strip, just pull it in...
Owners Manual - Page 7
.... Both carbon brushes should be used to the limit mark. Loosen the thumb screws which secure the casing. Replace a worn bit or poor fastening may damage the screw heads and cause wear on the tool by pulling the switch trigger. Replacing carbon brushes
1. A screw will damage the driving surface. • Do not apply oil or grease...
Owners Manual - Page 8
...or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Casing
1
2. Carbon brush
cap
1 2
008285
2
006304
Use a screwdriver to remove the carbon brush caps of any assistance for its stated purpose. Front cover 1 2. Recessed part
006816
2
3
Reinstall the front cover and tighten two screws securely. The use accessory or...
Owners Manual - Page 9
... A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. Some states do not allow the exclusion or limitation of normal wear and tear: the tool has been abused, misused or improperly maintained: alterations have other rights which vary from the date of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is...
Flyer (English) - Page 1
... Operation Efficiency and Decreasing Driver Noise
POWER
Powerful, high speed Makita built 4-pole motor handles decking and sub-floor (4,000 RPM)
CONVENIENCE
Collapsible screw guide reduces strip tangling and folds away
for easy storage
CONTROL
Rugged dust-proof autofeed tool design with a silent clutch
for easier operation
PERFORMANCE
Model BFR750 BFR750Z
LXT Li-Ion batteries charge in 30...
Flyer (English) - Page 2
... increasing operation efficiency and decreasing driver noise
I Screw guide prevents screw strip tangling and can fold against the autofeed housing for storing and carrying
I Tool belt hook can be moved to either side of AUTOFEED SCREWDRIVER accessories. 18V LXT LITHIUM-ION CORDLESS AUTOFEED SCREWDRIVER
Model BFR750/BFR750Z
FEATURES & BENEFITS
I Powerful Makita built 4-Pole motor handles decking...
Parts Breakdown - Page 2
... 75 ASS'Y INC. 1-36 SCREW GUIDE SET
Q'ty Unit 1 PC. 1 PC. 1 PC. 0 1 PC. 2 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 3 PC. 1 PC. 1 PC. 0 1 PC. Model BFR750/Z Parts List
A = Standard Equipment...
Parts Breakdown - Page 3
...91
233516-2
92
268188-4
INC. 82 TAPPING SCREW 4X18 HOUSING SET INC. 83 BFR750 NAME PLATE TAPPING SCREW 4X18 DUST COVER PLANE BEARING 14 O RING...TORSION SPRING L RUBBER PIN 4 FRONT COVER TAPPING SCREW 4X18 SCREW GUIDE SET INC. 41 HOUSING SET INC. 43 FLAT WASHER 26 TAPPING SCREW 4X18 GUIDE ATTACHMENT SET INC. 90 GUIDE ATTACHMENT SET INC. 89 TORSION SPRING 4 PIN 2
0 1 PC. 1 SET 0 1 PC. 9 PC. 1 PC....
Parts Breakdown - Page 4
093-1 A A01 A A02 O D01
310282-9 281217-6 B-10475 654510-5 BFR750Z
GUIDE HOOK +BIT 2-182L INSULATED CONNECTOR 5.5-SD TOOL ONLY
2 PC. 1 PC. 1 SET 1 PC.
Makita BFR750Z Reviews
We have not received any reviews for Makita yet.