Makita HM1111C Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita HM1111C manuals!
Problems with Makita HM1111C?
Ask a Question
Free Makita HM1111C manuals!
Problems with Makita HM1111C?
Ask a Question
Popular Makita HM1111C Manual Pages
HM1111C Instruction Manual - Page 2
...properly. Loose clothes, jewellery or long hair can cause you to a rotating part of the power tool may result in the off-position before turning the power... Keep proper footing and balance at all warnings and instructions for carrying, pulling or unplugging the power tool. ENGLISH (Original instructions)
SPECIFICATIONS
Model
HM1111C
HM1101C
Blows per minute
1,100 - 2,650
Overall ...
HM1111C Instruction Manual - Page 3
... for lubricating and changing accessories. 26. Maintain power tools. When using only identical replacement parts. Exposure to carry the current your power tool serviced by insulated gripping surfaces, when performing an operation where the cutting accessory may make exposed metal parts of children and do the job better and safer at the rate for...
HM1111C Instruction Manual - Page 4
...the bit or parts close to ... during extended use ) replace strict adherence
to the table...INSTRUCTIONS. USD203-2
Symbols
The followings show the symbols used for the relationship between the number settings on tool. Operate the tool only when hand-held. 12.
Do not point the tool at no one in
this instruction manual may be sure you have a firm footing. loosen up , hammering...
HM1111C Instruction Manual - Page 5
... not have this does not show trouble. For Model HM1111C only
Side handle (auxiliary handle) For tool with stick type side handle
1. Service
indicator lamp
(red)
2
2
011169...service indicator lamp flickers up , the mains cord or the controller may be shut off and
unplugged before installing the bit. Bit shank 2.
Indicator lamp
1. Then tighten the clamp nut securely. Installing...
HM1111C Instruction Manual - Page 6
...be secured in place by Makita
Authorized or Factory Service Centers only.
6 The bit...desired angle, slide the change the bit angle. OPERATION
Chipping/Scaling/Demolition
011172
To remove the bit, pull the releasing cover down a couple...
CAUTION: • Always be pushed in until it engages.
011171
After installing, always make sure that the tool will not increase the efficiency.
NOTE...
HM1111C Instruction Manual - Page 7
... stated purpose. Black
3
1 2
011178
Disconnect the connector by Makita Authorized or Factory Service Centers, always using Makita replacement parts. CAUTION: • Be careful not to damage the connector or lead
wires especially when installing the handle.
1. Connector 2. To maintain product SAFETY and RELIABILITY, repairs, any other accessories or attachments might present a risk of...
HM1111C Instruction Manual - Page 8
... to state. If inspection shows the trouble is thoroughly inspected and tested before leaving the factory. EN0006-1
8 MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty does not apply where:
repairs have been made to you. Some...
Makita HM1111C Parts Breakdown - Page 2
... SLIDE SLEEVE
035
213606-7 O RING 48
036
318604-7 CYLINDER GUIDE
037
313194-5 RING 39
038
234178-9 COMPRESSION SPRING 40
039
...PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. Model HM1111C Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
286285-4 TOOL HOLDER CAP
002
233948-3 RING SPRING 25
003
257308-5 RING 28
004
450064-8 CHUCK COVER...
Makita HM1111C Parts Breakdown - Page 3
...HOUSING COMPLETE TAPPING SCREW 5X25 FIX GUIDE CUSHION PLATE OIL SEAL 12 BALL...TAPPING SCREW 5X30 PLATE HANDLE BASE DUST COVER SUPPORT DUST COVER HM1111C NAME PLATE TAPPING SCREW 5X25 HANDLE RETAINER HANDLE... PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 0 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 SET 1 PC. 1 PC. 2 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 6 PC. 1 PC. 1 PC. 1 PC...
Makita HM1111C Parts Breakdown - Page 4
... HANDLE 68 COMPLETE INC. 119-121 SIDE HANDLE 68 ASS'Y INC. 117-124 BULL POINT 280 SDS-MAX GREASE VESSEL SET CLOTH PLASTIC CASE COMPLETE LATCH SHAFT HANDLE SPONGE 40-65 HM1111C PLASTIC CASE LABEL
1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC...
Makita HM1111C New Tool Flyer English - Page 1
... start-up reaction for increased user comfort and greater productivity
• Detached rear handle is an internal counterbalance system that greatly reduces vibration for more control and better accuracy
POWER
Powerful 14 AMP motor delivers 12.6 ft.lbs. AVT® Demolition Hammer Accepts SDS-MAX Bits
Model HM1111C
POWERFUL 14 AMP MOTOR DELIVERS 12.6 FT.LBS.
Makita HM1111C New Tool Flyer English - Page 2
...
n L.E.D. AVT® Demolition Hammer, Accepts SDS-MAX Bits
Model HM1111C
FEATURES & BENEFITS
n Powerful 14 AMP motor delivers 12.6 ft.lbs. For a complete listing, please refer to be set at makitatools.com, or call 1-800-4MAKITA. All models and accessories subject to change without prior notice. of impact energy to handle the most demanding applications
n Anti-Vibration Technology is...
Makita HM1111C Reviews
Do you have an experience with the Makita HM1111C that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!