Makita XCU06T Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XCU06T manuals!
Problems with Makita XCU06T?
Ask a Question
Free Makita XCU06T manuals!
Problems with Makita XCU06T?
Ask a Question
Popular Makita XCU06T Manual Pages
XCU06T Instruction Manual - Page 2
...3/8″
2 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XCU05
XCU06
Overall length (without guide bar)
256 mm (10-1/8″)
Rated voltage
D.C. 18 V
Net weight
2.8 - 3.3 kg (6.2 - 7.2 lbs)
Standard guide bar length
200 mm (8″)
250 mm (10″)
Recommended guide with 90PX bar length
200 - 250 mm (8″ - 10")
Applicable saw chain type (refer to the...
XCU06T Instruction Manual - Page 6
... positioning of the saw firmly in accordance with the chain cover being installed on ladders or when climbing with the chain saw. Regularly check the functionality of the wind. National regulation may cause chain breakage and/ or kickback.
• Follow the manufacturer's sharpening and maintenance instructions for damage and is made of thick leather are...
XCU06T Instruction Manual - Page 7
... personal injury.
Before using battery.
2.
SAVE THESE INSTRUCTIONS.
It may experience injury to excessive vibration may result in a container with product (gained from repeated use two hands when operating the chain saw chain and guide bar
Wear a helmet, goggles and ear protection. Do not use genuine Makita batteries. Please also observe possibly more detailed national...
XCU06T Instruction Manual - Page 11
...
Release the switch trigger to our authorized service center for proper repairs BEFORE further usage.
Hold the top handle with your right hand, the front handle with your hand. Unlocked position 3. CAUTION: Before installing the battery cartridge into the tool, always check to see that the chain saw comes to an immediate standstill.
3
2
1
2
1
2
3
►...
XCU06T Instruction Manual - Page 14
... bumper
NOTICE: When filling the chain oil for Makita chain saws or equivalent oil available in operation. OPERATION
Lubrication
Saw chain is automatically lubricated when the tool is adequate.
1
2
► 1 . Mineral oil may otherwise be impaired. 5. To install the spike bumper, perform the following steps: 1. NOTICE: Use the saw chain, and guide bar. 2. Tighten the retaining nut...
XCU06T Instruction Manual - Page 15
...parts of the body away from the bottom, the branch may close in and pinch the saw -horse or cradle. When cutting thick branches, first make a shallow undercut and then make the finish cut from the top without a shallow undercut, the branch may cause the guide... use a safe support (saw back a little. NOTICE: Never toss or drop the tool. NOTICE: Do not cover the vents of the chain saw body into ...
XCU06T Instruction Manual - Page 16
... ENGLISH For this presents a risk of kickback. Then attach the guide bar cover. This prevents the bar from the tool. Rest the chain saw and the front one to branches under tension, cut unsupported ...When limbing, support the chain saw off and the battery cartridge is used for cutting, the chain saw may only be deflected away from your direction if the chain becomes trapped....
XCU06T Instruction Manual - Page 17
...;
File and file guiding -
Different cutter lengths prevent the saw chain to one .
- culty, even when heavy pressure is applied; • The cutting edge is as shown in the figure.
► 1 . Use a suitable round file so that the proper sharpening angle is determined by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Diameter of...
XCU06T Instruction Manual - Page 20
... in the instruction manual.
Every 3 month
-
Switch trigger
Inspection.
-
-
-
-
- Annually - Sharpening
-
-
-
-
- Screws Inspection.
-
- Remove
-
-
-
-
- Lock-off lever
Inspection.
-
-
-
-
-
Check at
authorized
service
center.
-
- Saw chain Inspection.
-
-
-
-
-
Guide bar Inspection.
-
-
-
- Instructions for periodic maintenance...
XCU06T Instruction Manual - Page 21
TROUBLESHOOTING
Before asking for repairs, conduct your region for repair. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repair.
Recharge the battery cartridges. Turn on the chain. little use. No oil on the main power switch again. Oil guide groove is dropping.
Adjust the amount of oil delivery with a fully charged one . Battery power is ...
XCU06T Instruction Manual - Page 22
... warranty details set forth at below website for its stated purpose. If you purchase a guide bar of different length from country to country. MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms applicable to this manual. It must fit and fully cover the guide bar on the chain saw...
XCU06T Parts Breakdown - Page 4
...SUPPORT
1
1 38
281222-3 HOOK
1
1 39
183J48-8 HOUSING SET...CHAIN CATCHER
1
1 59
266905-6 H.L. No. XCU06 Tech Bulletin
1 XCU06
UNIT COMPLETE
Products with multiple versions are listed in subsiding order with the newest version on top not indented.
Part No. SOCKET HEAD BOLT M5X12
1
1 60
266388-0 TAPPING SCREW 5X16
1
1 61
266007-8 TAPPING SCREW BIND PT 3X10
1
1 62
347375-9 GUIDE...
XCU06Z Parts Breakdown - Page 4
... HOOK SUPPORT HOOK HOUSING SET DRIVE GEAR STRAIGHT BEVEL GEAR 14 CLAMP SCREW TENSION SLIDE TENSION SLIDE ADJUST SCREW STRAIGHT BEVEL GEAR 14 CLAMP SCREW HOUSING R COVER TAPPING SCREW 4X18 LINK PLATE COMPLETE COMPRESSION SPRING 7 BRAKE BAND BRAKE DRUM COMPLETE O RING 10 SPROCKET 6 SPROCKET 6 STOP RING E-7 GUIDE PLATE L GUIDE PLATE L CHAIN CATCHER H.L. 1 XCU06
UNIT COMPLETE...
XCU06T New Tool Flyer English - Page 1
... 10" Guide Bar (161846-0) • 10" Chain Saw Chain. 3/8", .043" (199075-5) • Bumper Spike (199068-2)
XCU06T
• 10" Guide Bar (161846-0) • 10" Chain Saw Chain. 3/8", .043" (199075-5) • Bumper Spike (199068-2) • 18V LXT® Lithium-Ion Rapid Optimum Charger (DC18RC) • (2) 18V LXT® Lithium-Ion 5.0Ah Battery (BL1850B)
2
3
4
5
All specifications subject...
XCU06Z New Tool Flyers English - Page 1
... 10" Guide Bar (161846-0) • 10" Chain Saw Chain. 3/8", .043" (199075-5) • Bumper Spike (199068-2)
XCU06T
• 10" Guide Bar (161846-0) • 10" Chain Saw Chain. 3/8", .043" (199075-5) • Bumper Spike (199068-2) • 18V LXT® Lithium-Ion Rapid Optimum Charger (DC18RC) • (2) 18V LXT® Lithium-Ion 5.0Ah Battery (BL1850B)
2
3
4
5
All specifications subject...
Makita XCU06T Reviews
We have not received any reviews for Makita yet.